Samsung Hp-p5031 Plasma Display Owners Instructions

							71
LNA (Low Noise Amplifier)
If the TV is operating in a weak-signal area, sometimes the LNA function can improve the
reception (a low-noise preamplifier boosts the incoming signal).
1
Press the MENU button. Press the ▲or ▼button to
select “Channel”, then press the ENTER button.
2 
Press the ▲or ▼button to select “LNA”, then press
the ENTER button.
3
Press the ▲or ▼button to select “On”, then press
the ENTER button.
• Pressing the 
▲or ▼button will alternate between
“On” and “Off”.
4 
Press the MENU button to exit.
Air/CATV : Air√Auto Program√Add/Delete√Fine Tune√LNA : Off√Scan√
ChannelTV
MoveEnterReturn
Air/CATV : Air
Auto Program
Add/Delete
Fine Tune
LNA :Off
Scan
ChannelTV
MoveEnterReturn
Air/CATV : Air
Auto Program
Add/Delete
Fine Tune
LNA :Off
Scan
ChannelTV
MoveEnterReturn
Off
On
Off
On
BN68-00714A-00_068~83  2004.5.6  1:9 PM  Page 71 
						

							BN68-00714A-00_068~83  2004.5.6  1:9 PM  Page 72 
						

							PLASMA DISPLAY PANEL
Connecting a PC and Operation
Connecting a PC ..........................................................................74
Adjusting the PC Screen................................................................78
Changing the Position of the Image ................................................79
Picture Quality Adjustment ............................................................80
Information ..................................................................................83
BN68-00714A-00_068~83  2004.5.6  1:9 PM  Page 73 
						

							Connecting a PC
Connection to a Macintosh computer may require an adapter.
74
Connecting a PC (15p D-SUB) to the PDP
Connecting a PC (DVI) to the PDP
Audio Cable
Audio CablePC Cable
DVI CablePower Plug
DVI jack(The actual configuration on
your PC may be different,
depending on the model.)
PDP
PC
or
Use a DVI-D 
connection cable.
(sold separately)
Connect a PC cable between the PC Output jack on the PC and the RGB input jack on the PDP.
Connect a Audio cable between the Audio jack on the PC and the Audio input jacks (PC INPUT) on the PDP.
1
2
Connect a DVI cable between the PC DVI jack on the PC and the DVI-D input jack on the PDP.
Connect a Audio cable between the Audio jack on the PC and the Audio L/R input (DVI INPUT) jacks on
the PDP.1
2
To watch the PC screen:
1. Turn on your PDP.
2. Press the SOURCE button on the remote control or SOURCE button on the front panel
to select “PC”.
3. Turn on your PC and check for PC system requirements. (Refer to pages 76 and 77 for PC 
system requirements.)
4. Adjust the PC screen. (Refer to pages 78 and 80.)
BN68-00714A-00_068~83  2004.5.6  1:9 PM  Page 74 
						

							75
Pin Configuration
D-Sub CableDVI-D Cable (Digital-Only Connector)
• 15Pin Signal Cable (based on protruded pin)
Setting up Your PDP (Plug and Play)
Our adoption of the new VESAPlug and Play solution eliminates complicated and time consuming
setup. It allows you to install your monitor in a Plug and Play compatible system, without the usual
setup hassles and confusion. Your PC system can easily identify and configure itself for use with your
display. This monitor automatically tells the PC system its Extended Display Identification data (EDID)
using Display Data Channel (DDC) protocols.  
BN68-00714A-00_068~83  2004.5.6  1:9 PM  Page 75 
						

							76
How to Set up Your PC Software (Windows only)
The Windows display-settings for a typical computer are shown below. However, the actual screens
on your PC will probably be different, depending upon your particular version of Windows and your
particular video card. Even if your actual screens look different, the same, basic set-up information will
apply in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.)
On the windows screen, select in the following
sequence : Start 
➝ Settings ➝ Control Panel.
When the control panel screen appears, click on
“Display” and a display dialog-box will appear.
Select the “Settings” tab in the display dialog-
box.
The two key variables that apply to the PDP-PC 
interface are “resolution” and “colors”. 
The correct settings for these two variables are:
•Size (sometimes called “resolution”)  
:1024 x 768 pixels.
•  Color: “32-bit” color 
Shown at left is a typical screen for “Display”
dialog box. 
If a vertical-frequency option exists on your 
display settings dialog box, the correct value is
“60” or “60 Hz”. Otherwise, just click “OK” 
and exit the dialog box.
Continued...
BN68-00714A-00_068~83  2004.5.6  1:9 PM  Page 76 
						

							77
Notes: 
Both screen position and size will vary, depending on the type of PC monitor and its resolution. 
The table below shows all of the display modes that are supported:
•The interlace mode is not supported.
•The PDP operates abnormally if a non-standard video format is selected.
•The table above conforms to IBM/VESA regulations and is based on using the Analog Input.
•“1280 x 1024” is not available in DVI mode.
Notes: 
•When this PDP is used as a PC display, 32-bit color is supported.
•Depending on the manufacturer, your PC display screen might appear different.
(and depending on your particular version of Windows.) 
Check your PC instruction book for information about connecting your PC to a PDP.
•If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 48.4kHZ 
(horizontal).
•In some cases, abnormal signals (such as stripes) might appear on the screen when the PC power 
is turned off (or if the PC is disconnected). If so, press the SOURCE button on the remote control 
or SOURCE button on the front panel to enter the VIDEO mode. Also, make sure that the PC is 
connected.
•Connect only a PC monitor to the monitor output port while viewing the PC screen. (Otherwise, 
random signals might appear).
Video Signal
IBM PC / AT
CompatibleResolution
(Dot X Line)Vertical
Frequency(Hz)
720 X 400
640 X 480
800 X 600
1024 X 768
1280 X 102470.087
59.940
72.809
75.000
85.008
56.250
60.317
72.188
75.000
85.061
60.004
70.069
75.029
84.997
60.020Horizontal
Frequency(KHz)
31.469
31.469
37.861
37.5
43.269
35.156
37.897
48.077
46.875
53.674
48.363
56.476
60.023
68.677
63.981Vertical
Polarity
P
N
N
N
N
N/P
P
P
P
P
N
N
P
P
PHorizontal
Polarity
N
N
N
N
N
N/P
P
P
P
P
N
N
P
P
P
BN68-00714A-00_068~83  2004.5.6  1:9 PM  Page 77 
						

							Adjusting the PC Screen
78
Adjusting the R.G.B
Preset: 
•Press the SOURCE button to select “PC”.
1 
Press the MENU button. Press the ▲or ▼button to
select “Picture”, then press the ENTER button.
2
Press the ▲or ▼button to select “Color Control”,
then press the ENTER button. 
The “Color Control” is available only when 
the “Color Tone” is set to Custom and a PC is 
connected.    
3
Press the ▲or ▼button to select the item you want
to change, then press the ENTER button. 
Press the 
œ or√button to change the value of the 
item, using the on-screen gauge as your guide.
4
Press the MENU button to exit.
Mode : Custom√Custom√Color Tone : Normal√Color Control√Film Mode : Off√Size : 16:9√PIP√
† More
PictureTV
MoveEnterReturn
R50
G50
B50
Color ControlTV
MoveEnterReturn
R50
BN68-00714A-00_068~83  2004.5.6  1:9 PM  Page 78 
						

							79
Changing the Position of the Image
After connecting the PDP to your PC, adjust the position of the screen if it is not well-aligned.
Preset: 
•Press the SOURCE button to select “PC.”
1 
Press the MENU button. Press the ▲or ▼button to
select “Setup”, then press the ENTER button. 
2
Press the ▲or ▼button to select “PC”, then press
the ENTER button. 
3 
Press the ▲or ▼button to select “Position”, then
press the ENTER button.
4 
Adjust the position of screen by pressing the 
▲/ ▼/ œ /√button.
5 
Press the MENU button to exit.
Language : English√
Time√
Caption√
Digital NR : On√
V-Chip√
Miscellaneous√
PC√
Color Weakness : Off√
SetupTV
MoveEnterReturn
Image Lock√
Position√
Information√
Auto Adjustment√
PCTV
MoveEnterReturn
PositionTV
MoveMoveReturn
PositionTV
MoveMoveReturn
BN68-00714A-00_068~83  2004.5.6  1:9 PM  Page 79 
						

							80
Picture Quality Adjustment
Picture Automatic Adjustment 
Preset: 
•Press the SOURCE button to select “PC”.
1 
Press the MENU button. Press the ▲or ▼button to
select “Setup”, then press the ENTER button.
2 
Press the ▲or ▼button to select “PC”, then press
the ENTER button.
3
Press the ▲or ▼button to select 
“Auto Adjustment”, then press the ENTER button.
The message “Auto Adjustment in progress.” 
appears on the screen and the picture adjustments 
are automatically activated.
4 
Press the MENU button to exit.
Air 11
Language : English√
Time√
Caption√
Digital NR : On√
V-Chip√
Miscellaneous√
PC√
Color Weakness : Off√
SetupTV
MoveEnterReturn
Image Lock√
Position√
Information√
Auto Adjustment√
PCTV
MoveEnterReturn
Auto Adjustment in progress.
Auto AdjustmentTV
BN68-00714A-00_068~83  2004.5.6  1:9 PM  Page 80