Samsung Hp-p5031 Plasma Display Owners Instructions
Have a look at the manual Samsung Hp-p5031 Plasma Display Owners Instructions online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1705 Samsung manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
31 Selecting the Video Signal-source Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the PDP (i.e., an antenna or a cable system). 1 Press the MENU button. Press the ▲or ▼button to select “Channel”, then press the ENTER button. 2 Press the ENTER button to select “Air/CATV”. 3 Press the ▲or ▼button to select “Air”, “STD”, “HRC” or “IRC”, then press the ENTER button. • If you are connected to an antenna, leave “Air” displayed. If you connected cable, press the ▲or ▼button to the display the type of cable system: “STD”, “HRC” or “IRC”. (If you are not sure which type of cable system you have, contact your cable company). 4 Press the MENU button to exit. Note •STD, HRC and IRC identify various types of cable TV systems. Contact your local cable company to identify the type of cable system that exists in your particular area. At this point the signal source has been selected. Proceed to “Storing Channels in Memory” (Next page). Memorizing the Channels Your PDP can memorize and store all of the available channels for both “off-air” (antenna) and cable channels. After the available channels are memorized, use the CH and CH buttons to scan through the channels. This eliminates the need to change channels by entering the channel digits. There are three steps for memorizing channels: selecting a broadcast source, memorizing the channels (automatic) and adding and deleting channels (manual). Air/CATV : Air√ Auto Program√ Add/Delete√ Fine Tune√ LNA : On√ Scan√ Channel TV MoveEnterReturn Air/CATV :Air Auto Program Add/Delete Fine Tune LNA : On Scan Channel TV MoveEnterReturn Air STD HRC IRC Air/CATV :Air Auto Program Add/Delete Fine Tune LNA : On Scan Channel TV MoveEnterReturn Air STD HRC IRC BN68-00714A-00_026~67 2004.5.6 11:56 AM Page 31
32 Storing Channels in Memory (Automatic Method) 1 First, select the correct signal source (Air, STD, HRC and IRC). See steps on previous page. Press the MENU button. Press the ▲or ▼button to select “Channel”, then press the ENTER button. 2 Press the ▲or ▼button to select “Auto Program”, then press the ENTER button. 3 Press the ENTER button. The PDP will begin memorizing all of the available channels. After all the available channels are stored, the Auto pro gram menu reappears. Press the ENTER button to stop. 4 Press the MENU button to exit. Note •The PDP automatically cycles through all of the available channels and stores them in memory. This takes about one to two minutes. ➤ ➤Quick way to access the Automatic Channel Setting: Just press the “AUTO PROG.” button on the remote control. Air/CATV : Air√ Auto Program√ Add/Delete√ Fine Tune√ LNA : On√ Scan√ Channel TV MoveEnterReturn Air/CATV : Air√ Auto Program√ Add/Delete√ Fine Tune√ LNA : On√ Scan√ Channel TV MoveEnterReturn Auto Program EnterReturn Start BN68-00714A-00_026~67 2004.5.6 11:56 AM Page 32
33 Adding and Erasing Channels (Manual Method) First, press the CH or CH button or the number buttons to select the channel you want to add or delete. 1 Press the MENU button. Press the ▲or ▼button to select “Channel”, then press the ENTER button. 2 Press the ▲or ▼button to select “Add/Delete”, then press the ENTER button. Repeatedly pressing ENTER button will alternate between “Add” and “Delete”. Press the CH or CH button to change channels you want to add or delete. 3 Press the MENU button to exit. Note •You can view any channel (including an erased channel) by using the number buttons on the remote control. Air/CATV : Air√ Auto Program√ Add/Delete√ Fine Tune√ LNA : On√ Scan√ Channel TV MoveEnterReturn Air/CATV : Air√ Auto Program√ Add/Delete√ Fine Tune√ LNA : On√ Scan√ Channel TV MoveEnterReturn Add/Delete EnterReturn Air 4 Deleted Add Change ➤ ➤Quick way to access the Adding and Erasing Channels : Just press the “ADD/DEL” button on the remote control. BN68-00714A-00_026~67 2004.5.6 11:56 AM Page 33
34 To View Memorized Channels (PIP Mode) 1 Press the MENU button. Press the ▲or ▼button to select “Channel”, then press the ENTER button. 2 Press the ▲or ▼button to select “Scan”, then press the ENTER button. Only the memorized channels are chosen. 3 Press the MENU button to stop. Air/CATV : Air√ Auto Program√ Add/Delete√ Fine Tune√ LNA : On√ Scan√ Channel TV MoveEnterReturn Scan Return Air 4 ➤ ➤When Channel scan starts, PIP mode will be activated automatically. The screen will remain in PIP mode when the SCAN has finished. Press the PIP button to exit PIP mode. BN68-00714A-00_026~67 2004.5.6 11:56 AM Page 34
35 Changing Channels Using the Channel Buttons Press the CH or CH button to change channels. When you press the CH or CH button, the PDP changes channels in sequence. You will see all the channels that the PDP has memorized. (The PDP must have memorized at least three channels.) You will not see channels that were either erased or not memorized. Directly Accessing Channels Press the number buttons to go directly to a channel. For example, to select channel 27, press “2” then “7”. The TV will change channels when you press the second number. When you use the number buttons, you can directly select channels that were either erased or not memorized. To change to single-digit channels (0~9) faster, press “0” before the single digit. (For channel “4” press “0”, then “4”). Using the PRE-CH button to select the previous channel Press the PRE-CH button. The TV will switch to the last channel viewed. To quickly switch between two channels that are far apart, tune to one channel, then use the number button to select the second channel. Then, use the PRE-CH button to quickly alternate between them. Adjusting the Volume Using the Volume Buttons Press the VOL + or VOL – button to increase or decrease the volume. Using Mute Using the MUTE Buttons At any time, you can temporarily cut off the sound using the MUTE button. 1 Press the MUTE button and the sound cuts off. The word “Mute” will appear in the lower-left corner of the screen. 2 To turn mute off, press the MUTE button again, or simply press the VOL + or VOL – button. Mute
36 Setting Up Your Remote Control This PDPs remote control can operate almost any VCR, cable box or DVD. After it has been set up properly, your remote control can operate in four different modes :TV , VCR, Cable, DVD or STB. Pressing the corresponding button on the remote control allows you to switch between these modes, and control whichever piece of equipment you choose. Note : ●The remote control may not be compatible with all DVD Players, VCRs, Cable boxes. ●The remote control can only operate STB made by Samsung. Setting Up the Remote to Operate Your VCR, Cable box or DVD player 1 Turn off your VCR. (or Cable box, DVD player) 2 Press the MODE button. The Mode is changed whenever MODE button is pressed. 3 Press the SET button on your TVs remote control. 4 Using the number buttons on your remote control, enter three digits of the VCR (or Cable box, DVD player) code listed on page 37 of this manual for your brand of VCR (or CATV, DVD). Make sure you enter three digits of the code, even if the first digit is a 0. (If more than one code is listed, try the first one.) 5 Press the POWER button on the remote control. Your VCR (or CATV, DVD) should turn on if your remote is set up correctly. If your VCR (or CATV, DVD) does not turn on after setup, repeat steps 2, 3, and 4, but try one of the other codes listed for your brand of VCR (or CATV, DVD). If no other codes are listed, try each code, 000 through 089 (or Cable box: 000 through 077, DVD player: 000 through 008). Notes •When your remote control is in “VCR” mode, the VCR control buttons (STOP, REW, PLAY/PAUSE, FF) still operate your VCR. •When your remote control is in “CATV” or “DVD” mode, the VCR control buttons (STOP, REW, PLAY/PAUSE, FF) still operate your VCR. •You do not need to program the remote for Samsung STBs as the codes are pre-programmed. BN68-00714A-00_026~67 2004.5.6 11:56 AM Page 36
37 Remote Control Codes VCR Codes Cable Box Codes DVD Codes BN68-00714A-00_026~67 2004.5.6 11:56 AM Page 37
38 Setting the Signal Source 1 Press the MENU button. Press the ENTER button to select “Input”. 2 Press the ENTER button to select “Source List”. 3 Press the ▲or ▼button to select signal source, then press the ENTER button. 4 Press the MENU button to exit. Notes •When you connect equipment to the PDP, you can choose between the following sets of jacks: AV1, AV2, S-Video, Component1, Component2, PC or DVI on the PDP’s rear panel. Viewing an External Signal Source Use the remote control to switch between viewing signals from connected equipment, such as VCRs, DVD, Set-Top box and the TV source (broadcast or cable). Source List : TV√ Edit Name√ Input TV MoveEnterReturn TV AV1- - - -AV2- - - -S-Video- - - -Component1- - - -Component2- - - -PC- - - -DVI- - - - Source List TV MoveEnterReturn TV AV1VCR AV2 - - - -S-Video- - - - Component1- - - -Component2- - - -PC- - - - DVI- - - - Source List TV MoveEnterReturn ➤ ➤Quick way to access viewing an external signal source : Just press the “SOURCE” button on the remote control. BN68-00714A-00_026~67 2004.5.6 11:56 AM Page 38
Assigning Names to External input mode 1 Press the MENU button. Press the ENTER button to select “Input”. 2 Press the ▲or ▼button to select “Edit Name”, then press the ENTER button. 3 Press the ENTER button. Press the ▲or ▼button to select external device, then press the ENTER button. • You can select the VCR, DVD, Cable STB, HD STB, Satellite STB, AV Receiver, DVD Receiver, Game, Camcorder, DVD Combo, DHR or PC. • Set other signal sources (AV2, S-Video, Component1, Component2, PC or DVI) using the same method as listed above. 4 Press the MENU button to exit. Notes •DHR : DVD HDD Recorder 39 Edit Name Source List : TV√ Edit Name√ Input TV MoveEnterReturn Edit Name AV1 :- - - -√ AV2 :- - - -√ S-Video :- - - -√ Component1 :- - - -√ Component2 :- - - -√ PC :- - - -√ DVI :- - - -√ Edit Name TV MoveEnterReturn AV1 :- - - -√ AV2 :- - - -√ S-Video :- - - -√ Component1 :- - - -√ Component2 : PC : - - - -√ DVI : Edit Name TV MoveEnterReturn - - - - VCR DVD Cable STB HD STB Satellite STB † BN68-00714A-00_026~67 2004.5.6 11:56 AM Page 39