Samsung Hp-p5031 Plasma Display Owners Instructions

							1 
The wall mount comes packaged in 3 parts. These parts must be assembled together.
Please tighten the captive screw in the direction of the arrow after assembling 
the bracket. Install the Wall Mount Bracket after the screws are securely inserted 
into the wall.
2 
After installing the Wall Mount  Bracket,
assemble the support bars and hinges 
(as illustrated) using screws provided. 
(12 screws(
@) are provided. For safety
reasons, make sure all 12 screws are 
firmly attached.)
11
How to assemble the Wall Mount Bracket
ASSY-HINGE (LEFT)
Separate ASSY-HINGE 
into Left and Right.Wall Mount Bracket
Wall Mount Bracket
Support Bars
Support BarsCaptive Screws
ASSY-HINGE
(RIGHT)
ASSY-HINGE
(LEFT)
ASSY-HINGE
(RIGHT)
3 
After securing the screws, be sure that
every part is firmly attached (as shown 
in the illustration).
ASSY-
HINGE
(LEFT)
ASSY-HINGE
(RIGHT)
BN68-00714A-00_002~25  2004.5.6  11:52 AM  Page 11 
						

							1 
Remove the screws from the back of the PDP.
2 
Connect insulation holders to screws (see the illustration below).
• If you are uncertain about installation, hire a specialist to install the wall mount bracket.
• Be sure to check that the insulation holders are completely secured on both the left
and right side after hanging the PDP on the wall mount bracket.
• Be careful to avoid getting your fingers caught during installation.
• Make sure the wall attachment panels are tightened. Otherwise the PDP may fall.
Note
•A 5 inch gap is needed between the back of the Plasma TV and the wall.
Wall Installation Instructions
12
Fixing the PDP panel to the wall attachment panel bracket
3 
Tighten the screws of the insulation
holders to the back of the PDP.
4 
Put the 4 insulation holders on the PDP
in the grooves of the wall mount 
bracket and pull down on the PDP (Œ) 
to secure it to the wall mount bracket 
(´). Tighten the screws as shown (ˇ) 
so that the PDP cannot be separated 
from wall mount bracket.
PDP panel
Wall attachment panel
bracketWall
Œ
´ˇ
BN68-00714A-00_002~25  2004.5.6  11:52 AM  Page 12 
						

							13
Note
•Contact an authorized technician when installing the wall attachment panel.
•After hanging the PDP panel on the wall attachment panel, make sure that the Insulation 
holders are completely hung. 
•Be careful not to get your fingers caught during installation.
•Make sure the wall attachment panel brackets are tightened. Otherwise, the PDP panel may 
fall down.
•Please secure the mounting bracket on the wall surface after setting its angle at 0°.
How to Adjust Mounting Angle
Notice  Notice : Please secure the mounting bracket on the wall surface after setting its angle at 0°.
Factory default How to Adjust Mounting Angle
Please tighten the captive screw in the direction
of the arrow after assembling the bracket.Hold onto the middle of the PDP to adjust 
the angle (not the sides of the PDP).
1
Secure the SET to the wall mount bracket.
(Please refer to the following instructions.)
2
Set the angle by pulling the upper end of the SET attached 
to bracket in the direction of the arrow. 
3
The angle can be adjusted from 0° to 15° by ±2°.
Change Angle
1
Be sure to remove the safety pins underneath the PDP.
(Caution: If the safety pins are not removed, the angle cannot 
be adjusted.) Any attempt to do so may cause damage to the PDP.
2
Hold onto the bottom of the PDP and pull forward fully as 
directed by the arrow(as illustrated) to adjust the angle. 
(0°~20° by 2°). Insert the Safety Pins to the front guide 
holes on both sides as illustrated in figure 
´.
3
Viewing the PDP after connecting the external devices.
Remove the Safety Pins to adjust the angle to 0°, and then 
secure the Safety Pins again. (Warning: For safety, be sure to 
secure the PDP using the safety pins. If the safety pins are not 
used, the PDP may fall, causing serious injury.)
Connecting External Devices to the PDP
BN68-00714A-00_002~25  2004.5.6  11:52 AM  Page 13 
						

							Connecting Speakers
14
1 
Remove the screws on the rear of the PDP.
2 
Hang the two “T” shaped hangers on the square holes on the rear of the PDP.
3 
Tighten the PDP and the speaker bracket using the screws removed from the PDP.
➤ ➤When moving your PDP, do NOT hold the speaker connected to your PDP. It may damage the bracket
clamping the speaker and your PDP together and result in a drop of your PDP and a risk of personal
damage and injury.
BN68-00714A-00_002~25  2004.5.6  11:52 AM  Page 14 
						

							15
Connect the speaker audio cable to the external speaker output jack on the rear of the PDP matching the
“+” and “-” ends of the cable with the diagram on the PDP.
➤ ➤The speakers MUST have to a power handling capability of 10 watts minimum (impedance 8Ω).
When you connect the speaker wire to the external speaker out connector, first bind the speaker wire round the ferrite core to secure it.
Ferrite Cores
The ferrite cores are used to attenuate undesired signals.
When connecting cables, attach one of these ferrite cores to the cable
near the connector.
BN68-00714A-00_002~25  2004.5.6  11:52 AM  Page 15 
						

							16
How to assemble the Stand-Base
1 
Assemble two support pins with the stand base and firmly secure both sides of the 
support pins using 8 screws provided.
2 
Assemble the PDP with the stand and firmly secure the PDP using 4 screws provided.
➤ ➤Two or more people should carry the PDP. Never lay the PDP on the floor because of possible damage
to the screen. Always store the PDP upright.
BN68-00714A-00_002~25  2004.5.6  11:53 AM  Page 16 
						

							PLASMA DISPLAY PANEL
Connections
Connecting VHF and UHF Antennas ..............................................18
Connecting Cable TV ....................................................................19
Connecting a VCR ........................................................................21
Connecting a Camcorder ..............................................................22
Connecting a DVD Player ..............................................................23
Connecting a DTV Receiver ..........................................................24
BN68-00714A-00_002~25  2004.5.6  11:53 AM  Page 17 
						

							Connecting VHF and UHF Antennas
18
Antennas with 75-ohm Round Leads
If your antenna looks like this:  it has 75-ohm round leads.  
1
Plug the antenna lead into the VHF/UHF terminal 
on the PDP.
Use the Antenna Cable, an accessory included 
in the product package. 
BN68-00714A-00_002~25  2004.5.6  11:53 AM  Page 18 
						

							19
Connecting Cable TV
You can connect different cable systems to your PDP, including cable without a cable box, 
and cable with a cable box that descrambles some or all channels.
Cable without a Cable Box
1 
Plug the incoming cable into the VHF/UHF terminal on
the PDP.
Use the Antenna Cable, an accessory included 
in the product package.
Cable with a Cable Box that Descrambles All Channels
1 
Find the cable connected to the ANTENNA OUT 
terminal on your cable box. This terminal might be 
labeled ANT OUT, VHF OUT or simply OUT.
2 
Connect the cable to the VHF/UHF terminal on the
PDP. 
Use the Antenna Cable, an accessory included 
in the product package. 
BN68-00714A-00_002~25  2004.5.6  11:53 AM  Page 19 
						

							20
Cable with a Cable Box that Descrambles Some (But Not All) Channels
To complete this connection you will need a two-way splitter, an RF (A/B) switch, and four coaxial
cables (which you can buy from your Samsung dealer or any electronics store).
1
Find and disconnect the cable that is 
connected to the ANTENNA IN terminal of
your cable box. 
This terminal might be labeled ANT IN, 
VHF IN or simply, IN. Connect this 
cable to a two-way splitter.
2
Connect a coaxial cable between an 
OUTPUT terminal of the splitter and the 
IN terminal of the cable box.
3
Connect a coaxial cable between the
ANTENNA OUT terminal of the cable box 
and the B-IN terminal of the A/B switch.
4
Connect a coaxial cable between the
ANTENNA OUT terminal of the cable box 
and the B-IN terminal of the A/B switch.
5
Connect the last coaxial cable between the
OUT terminal of the RF (A/B) switch and 
the VHF/UHF terminal on the PDP.
After youve made this connection, set the A/B switch to the A position for normal viewing. 
Set the A/B switch to the B position to view scrambled channels. (When you set the A/B switch 
to B, you will need to tune your Set-Top Box to the cable boxs output channel, which is usually
channel 3 or 4.)
BN68-00714A-00_002~25  2004.5.6  11:53 AM  Page 20