Samsung Hp-p5031 Plasma Display Owners Instructions

1 
The wall mount comes packaged in 3 parts. These parts must be assembled together.
Please tighten the captive screw in the direction of the arrow after assembling 
the bracket. Install the Wall Mount Bracket after the screws are securely inserted 
into the wall.
2 
After installing the Wall Mount  Bracket,
assemble the support bars and hinges 
(as illustrated) using screws provided. 
(12 screws(
@) are provided. For safety
reasons, make sure all 12 screws are 
firmly attached.)
11
How to assemble the...

1 
Remove the screws from the back of the PDP.
2 
Connect insulation holders to screws (see the illustration below).
• If you are uncertain about installation, hire a specialist to install the wall mount bracket.
• Be sure to check that the insulation holders are completely secured on both the left
and right side after hanging the PDP on the wall mount bracket.
• Be careful to avoid getting your fingers caught during installation.
• Make sure the wall attachment panels are tightened. Otherwise the PDP...

13
Note
•Contact an authorized technician when installing the wall attachment panel.
•After hanging the PDP panel on the wall attachment panel, make sure that the Insulation 
holders are completely hung. 
•Be careful not to get your fingers caught during installation.
•Make sure the wall attachment panel brackets are tightened. Otherwise, the PDP panel may 
fall down.
•Please secure the mounting bracket on the wall surface after setting its angle at 0°.
How to Adjust Mounting Angle
Notice  Notice :...

Connecting Speakers
14
1 
Remove the screws on the rear of the PDP.
2 
Hang the two “T” shaped hangers on the square holes on the rear of the PDP.
3 
Tighten the PDP and the speaker bracket using the screws removed from the PDP.
➤ ➤When moving your PDP, do NOT hold the speaker connected to your PDP. It may damage the bracket
clamping the speaker and your PDP together and result in a drop of your PDP and a risk of personal
damage and injury.
BN68-00714A-00_002~25  2004.5.6  11:52 AM  Page 14 

15
Connect the speaker audio cable to the external speaker output jack on the rear of the PDP matching the
“+” and “-” ends of the cable with the diagram on the PDP.
➤ ➤The speakers MUST have to a power handling capability of 10 watts minimum (impedance 8Ω).
When you connect the speaker wire to the external speaker out connector, first bind the speaker wire round the ferrite core to secure it.
Ferrite Cores
The ferrite cores are used to attenuate undesired signals.
When connecting cables, attach one of...

16
How to assemble the Stand-Base
1 
Assemble two support pins with the stand base and firmly secure both sides of the 
support pins using 8 screws provided.
2 
Assemble the PDP with the stand and firmly secure the PDP using 4 screws provided.
➤ ➤Two or more people should carry the PDP. Never lay the PDP on the floor because of possible damage
to the screen. Always store the PDP upright.
BN68-00714A-00_002~25  2004.5.6  11:53 AM  Page 16 

PLASMA DISPLAY PANEL
Connections
Connecting VHF and UHF Antennas ..............................................18
Connecting Cable TV ....................................................................19
Connecting a VCR ........................................................................21
Connecting a Camcorder ..............................................................22
Connecting a DVD Player ..............................................................23
Connecting a DTV Receiver...

Connecting VHF and UHF Antennas
18
Antennas with 75-ohm Round Leads
If your antenna looks like this:  it has 75-ohm round leads.  
1
Plug the antenna lead into the VHF/UHF terminal 
on the PDP.
Use the Antenna Cable, an accessory included 
in the product package. 
BN68-00714A-00_002~25  2004.5.6  11:53 AM  Page 18 

19
Connecting Cable TV
You can connect different cable systems to your PDP, including cable without a cable box, 
and cable with a cable box that descrambles some or all channels.
Cable without a Cable Box
1 
Plug the incoming cable into the VHF/UHF terminal on
the PDP.
Use the Antenna Cable, an accessory included 
in the product package.
Cable with a Cable Box that Descrambles All Channels
1 
Find the cable connected to the ANTENNA OUT 
terminal on your cable box. This terminal might be 
labeled ANT...

20
Cable with a Cable Box that Descrambles Some (But Not All) Channels
To complete this connection you will need a two-way splitter, an RF (A/B) switch, and four coaxial
cables (which you can buy from your Samsung dealer or any electronics store).
1
Find and disconnect the cable that is 
connected to the ANTENNA IN terminal of
your cable box. 
This terminal might be labeled ANT IN, 
VHF IN or simply, IN. Connect this 
cable to a two-way splitter.
2
Connect a coaxial cable between an 
OUTPUT terminal of...