Samsung HL-S5086W DLP TV User Manual

							Connecting a DVD Player
The rear panel jacks on your TV make it easy to connect a DVD player to your TV.
Connecting to Y, PB, PR
1
Connect a set of audio
cables between the 
COMPONENT (1 or 2)
AUDIO (L, R) IN jacks on 
the TV and the AUDIO OUT
jacks on the DVD player.
2
To enable Component video
viewing, connect a set of 
video cables between the 
COMPONENT (1 or 2) 
VIDEO (Y, P
B, PR) IN jacks 
on  the TV and VIDEO 
(Y/P
B/PRor Y/CB/CR) OUT 
jacks on the DVD player.  
Connecting to Audio and Video Jacks
1
Connect a set of audio
cables between the AUDIO
IN (1 or 2) jacks on the TV
and the AUDIO OUT jacks
on the DVD player.
2
Connect a video cable
between the VIDEO IN (1 
or 2) jack on the TV and the
VIDEO OUT jack on the 
DVD player.
NOTES
•Component Video separates
the video into Y(Luminance
(Brightness)), P
B(Blue) and PR
(Red) for enhanced video
quality.
•Please be sure to match the
color coded input terminals
and cable jacks.
DVD Player
Incoming
Cable or 
Antenna
TV Rear Panel
DVD Player
Incoming
Cable or 
AntennaTV Rear Panel
1
1
2
2
English - 21
BP68-00586A-00Eng(016~025)  2/13/06  2:17 PM  Page 21 
						

							Connecting a DTV Set-Top Box
Connecting to Y, PB, PR
1
Connect a set of audio
cables between the 
COMPONENT (1 or 2) 
AUDIO (L, R) IN jacks on 
the TV and the AUDIO OUT 
jacks on the Set-Top Box.
2
Connect a set of video
cables between the 
COMPONENT (1 or 2) 
VIDEO (Y, P
B, PR) IN jacks 
on the TV and VIDEO 
(Y/P
B/PRor Y/CB/CR) OUT 
jacks on the Set-Top Box.
NOTE
•Please be sure to match the
color coded input terminals
and cable jacks.
Connections
English - 22
TV Rear Panel
DTV Set-Top Box
Incoming
Cable or 
Antenna
12
Connecting to HDMI (High Definition Multimedia Interface)
1
Connect an HDMI cable
between the HDMI IN 1
jack on the TV and the HDMI
OUT jack on the Set-Top Box.
NOTE
•Make sure the HDMI/DVI
source’s power is on, or you
will be unable to select it in the
TV menu’s source list.
TV Rear Panel
DTV Set-Top Box Incoming
Cable or 
Antenna
1
BP68-00586A-00Eng(016~025)  2/13/06  2:17 PM  Page 22 
						

							English - 23
Connecting to DVI (Digital Visual Interface)
1
Connect a set of audio
cables between the DVI
AUDIO (L, R) IN jacks on the
TV and the AUDIO OUT
jacks on the Set-Top Box.
2
Connect an HDMI/DVI cable
between the HDMI 2/DVI IN
jack on the TV and the DVI
OUT jack on the Set-Top Box.
NOTES
•Make sure the DVI source’s
power is on, or you will be
unable to select it in the
TV menus source list.
•The HDMI/DVI IN jack is not 
compatible with PC.
Connecting a Digital Audio System
There are many types of digital audio systems on the market today.
A simplified illustration of an audio system is shown below. 
For more information, see your audio system owner’s manual.
1
If your audio system has an
optical digital audio input,
connect to the DIGITAL
AUDIO OUT (OPTICAL) jack
on the TV.
NOTE
•OPTICAL: converts the electric
signal into an optical light
signal, and transmits it through
glass fibers.
•When a Digital audio system is
connected to the Digital Audio
Out (Optical) terminal:
Decrease the gain (volume) of
the TV, and adjust the volume
level with the audio systems
volume control.
TV Rear Panel
DTV Set-Top Box
Incoming
Cable or 
Antenna
12
TV Rear Panel
Audio System
1
BP68-00586A-00Eng(016~025)  2/16/06  11:04 AM  Page 23 
						

							Connecting to an Analog Amplifier
1
The AV OUT (AUDIO L/R)
terminals cannot be used for 
external speakers. 
You must hook them up to an
amplifier.
When an audio amplifier is 
connected to the AV OUT 
(AUDIO L/R) terminals: 
Decrease the gain (volume) 
of the audio amplifier, and
adjust the volume level with
the volume control on the TV.
NOTE
•If using the HDMI/DVI, PC, or
Component input on the TV, the
audio output signal is available
only when the TV’s Internal Mute
is set to on.   
(Refer to page 79)
Connections
English - 24
TV Rear Panel
Amplifier
1
Internal Speakers Audio Out (Optical, L/R Out)
RF AV, S-Video
Component, PC, HDMIRF AV, S-VideoComponent, PC, HDMI
Internal Mute OffSpeaker Output Speaker Output Speaker OutputSound Output Sound Output Sound Output 
Internal Mute OnInactive Inactive Inactive Sound Output Sound Output Sound Output
Video No OutInactive Inactive Inactive Inactive Inactive Inactive
When “Internal mute” is set to “On”, Sound menus except “Multi-Track Options” and “Digital Output”
cannot be adjusted.
BP68-00586A-00Eng(016~025)  2/23/06  1:40 PM  Page 24 
						

							Operation
BP68-00586A-00Eng(016~025)  2/13/06  2:17 PM  Page 25 
						

							Turning the TV On and Off
Press the POWER button on the remote control.
You can also use the POWER button on the front panel.
Plug & Play Feature
When the TV is initially powered On, basic customer settings proceed automatically and subsequently:
Setting the language, checking the antenna input, memorizing the channels, and setting the time.
NOTE
•The Plug & Play function operates after plugging in the TV for the first time.
English - 26
Operation
1
Press the POWER button on the remote
control. The message “Menu language,
Channels and Time will be set.” is 
displayed.
Press the ENTER button, then the 
Language menu is displayed.
2
Press the ENTER button to enter the 
language. Press the …or †button to
select language, then press the ENTER
button. “Selects the antenna to execute
the Auto Program Function.” menu is 
automatically displayed.
3
Press the …or †button to memorize 
the channels of the selected connection. 
Press the ENTER button to select “Start”.
Continued...
Plug & Play
Skip
Select the language of the OSD.
Language
English
Español
Français
Plug & Play
EnterSkip
Air
Cable
Air+Cable Selects the antenna to execute the
Auto Program function.StartStart
Start
Move
EnterMove
•If the antenna is connected to ANT 1
IN (CABLE), select “Cable” and if it 
is connected to ANT 2 IN (AIR), 
select “Air”.
•If both ANT 1 IN and ANT 2 IN are
connected, select the “Air + Cable”. •The Language menu will automatically
appear after several seconds, even if
the ENTER button is not pressed.
•The message to check the connected
status of the antenna is displayed.
Menu language, Channels and
Time will be set.i
Start
BP68-00586A-00Eng(026~047)  2/13/06  2:18 PM  Page 26 
						

							English - 27
4
Press the ENTER button to start the auto
program. By default, the cable TV system
is set to “STD”.
If you want to select another type of 
cable system, press the œbutton and 
use the …or †button to select 
“STD”, “HRC” or “IRC”. 
Press the ENTER button.
5
The TV will begin memorizing all of the
available channels. 
After all the available channels are
stored, the Auto program menu 
reappears. Press the ENTER button at 
any time to interrupt the memorization
process. 
Press the ENTER button, then the menu 
to set the clock mode is automatically 
displayed.
6
Press the ENTER button to select “Clock
Mode”.
Press the …or † button to select “Auto”
or “Manual”, then press the ENTER 
button.
Continued...
Plug & Play
EnterSkip
Selects a cable signal type for your
location.
Move
StartHRC
IRC
Auto Program
Skip
Auto Program is incomplete.
14 channels are memorized.
Air : 9     Cable : 5
Plug & Play
Sets the current time manually or automatically.
Clock Mode
•
STD, HRC, and IRC identify various
types of cable TV systems. Contact
your local cable company to identify
the type of cable system that exists in
your particular area. At this point the
signal source has been selected. 
EnterSkipMove
Auto Program
EnterSkip
Auto program in progress.
Cable 26
37%Stop
Auto
Manual
STD
BP68-00586A-00Eng(026~047)  2/13/06  2:18 PM  Page 27 
						

							Option 1: Setting the Clock Automatically
If you set “Clock Mode” to “Auto” in step 6, follow the instructions below.
7
Press the ENTER button to select
“DST”(Daylight Saving Time).
Press the …or †button to select “Off” or
“On”, then press the ENTER button.
8
Press the …or †button to select time
zone, then press the ENTER button.
Press the …or †button to highlight the
time zone for your local area (and to
move the highlight to the appropriate time
zone on the map of the United States),
then press the ENTER button.
9
The message “Enjoy your watching.” is 
displayed. When you have finished, 
press the ENTER button.
Operation
•When you set up Auto Time, the set time may
not be correct depending on the broadcasting
station and signal. If there is a difference
between the real time and set time, please set
the time manually.
Plug & Play
EnterSkip
Select the time zone where you locate.
Move
Newfoundland
Atlantic
Eastern
Central
Mountain
Pacific
Alaska
Hawaii
Plug & Play
Set to daylight saving time.
DST
Enjoy your watching.i
OK
Option 2: Setting the Clock Manually
If you set “Clock Mode” to “Manual” in step 6, follow the instructions below.
7
Press the œor √button to move to
“Month”, “Day”, “Year”, “Hour”,
“Minute”, or “am/pm”. 
Set the clock you want by pressing 
the …or † button, then press the 
ENTER button.
8
The message “Enjoy your watching.” is 
displayed. When you have finished, 
press the ENTER button.
Plug & Play
Enter the current date and time.
HourMinute am/pm-- -- --
MonthDay       Year▲--------▼
AdjustSkipMove
Enjoy your watching.i
OK
•You can set the month, day,
year, hour and minute directly
by pressing the number buttons
on the remote control.
English - 28
EnterSkipMove
Enter
Off
On
BP68-00586A-00Eng(026~047)  2/13/06  2:18 PM  Page 28 
						

							English - 29
Viewing the Menus and On-Screen Displays
The on-screen menu system allows you to control the settings of your TV. Access the on-screen menu 
system by pressing the MENU button on the remote control. Once the on-screen menu appears, use
the …/†/œ/√/ENTER buttons on your remote control to select menu items and make adjustments. 
You can also view the on-screen menu system and make some adjustments using the TV’s front panel 
buttons.
Viewing the Menus
1
Press the MENU button.
The main menu is displayed.
There are five menu groups:
“Input”, “Picture”, “Sound”,
“Channel”, and “Setup”.
2
Press the …or †button to
select an item you want 
in the menu. 
Press the œ, √or ENTER 
button to display, change, 
or use the selected items.
Use the ENTER button to
enter items in the menu.
3
Press the EXIT button to exit.
Viewing the Display
Press the INFO button on the
remote control. 
The TV displays the current 
channel, the status of certain 
picture and sound settings and 
the current time.
The information displayed varies
according to the selected source.Air 3
Picture Mode
Sound Mode
MTS
Caption
V-Chip
12:00 am: Standard
: Custom
: Mono
: Off 
: Off
Picture
Mode : Standard√Size : 16:9√Digital NR : On√DNIe : On√My Color Control√Film Mode : Off√
MoveEnterReturn
Input
Source List : TV√Edit Name√WISELINK√
MoveEnterExit
Mono
BP68-00586A-00Eng(026~047)  2/13/06  2:18 PM  Page 29 
						

							English - 30
Operation
Selecting a Menu Language
1
Press the MENU button. 
Press the …or †button to
select “Setup”, then press the
ENTER button.
2
Press the ENTER button to
select “Language”.
Press the …or †button to
select “English”, “Español” 
or “Français”, then press the
ENTER button.
Press the EXIT button to exit.
Setup
Language : English√Time√Game Mode : Off√V-Chip√Caption√Menu Transparency: Medium√Blue Screen : Off√
MoveEnterReturn
Setup
Language: English
Time
Game Mode : Off
V-Chip
Caption
Menu Transparency: Medium
Blue Screen : Off
MoveEnterReturn
† More
† More
English
Español
Français
BP68-00586A-00Eng(026~047)  2/13/06  2:18 PM  Page 30