Samsung H 264 Manual

							REMOTE OPERATION 
36 
Full Function Version 
 
Main Button Overview 
Button 
Function Description 
Simplified Full 
Function 
  Address Book Click to show the predefined IP address(es). You 
can add, remove or search the IP address to log 
in the DVR remotely. 
  Miscellaneous 
Control 
Remote 
Config Click to go into the detailed 
DVR setting. 
 Record 
Setting Click to go to the detailed 
record setting. 
Custom 
Setting Click to choose the language of 
this program. The language 
change will take effect when 
this program is closed and 
executed again. 
  Log Click to view all event and recording logs, search 
the desired log(s) by date, or playback the  
						

							REMOTE OPERATION 
37 
Button 
Function Description 
Simplified Full 
Function 
recording of the selected log. 
 /   /  Record /   
Record Stop Click to start / stop the manual recording.   
  Snapshot Click to take a snapshot of the current view. The 
snapshot will be saved in the path you specified in 
“Record Setting”.   
  
Information Click to show the current network connection 
details.  
  DVR Control Click to go to the DVR control panel to operate 
the DVR remotely. 
6.1.3. General Operation 
Record
 
To record remotely at the same time for any event or alarm at the DVR side, click “” 
or “
” → “” to go to the “Record Setting” page.   
 
In the “Record Setting” page, you can set the following items: 
‧Record type 
‧Hard disk overwriting  
						

							REMOTE OPERATION 
38 
‧Pre- / post-alarm record 
‧Record time setting 
‧Record path 
If “Manual” is checked, click “
” or “” on the main control panel to start the 
manual recording immediately, and the recordings will be saved in the specified location.   
If “Motion” and / or “Alarm” are checked, the recording function will also be enabled at the 
remote side when any event is triggered at the DVR side, and the recordings will be 
saved in the specified location. 
Playback 
To play a recording, click “” or “”, and select the “Record” tab or “Backup” tab. A 
list of all the recordings will be shown by defaults, and you can also sort out the logs you 
want to speed up the search time.   
 
To immediately play a recording, select a log from the list, and click “Play”, or 
double-click the selected log.   
Network Backup 
Click “” → “”, or click “” to go into the “Backup” page as follows, and you 
can select a specific time range or event to make a video backup remotely.    
						

							REMOTE OPERATION 
39 
The file(s) you backup will be from the currently selected IP address. 
 
Function Description 
HDD Number / Channel  Specify the hard disk (HDD Number) and channel number 
(Channel) within which have the video data you need. 
Download by Time  Specify the time range within which has the video data you want in 
the “Start Time” and “End Time” columns.   
Download by Event  Select an event log from the event list. This list shows all logs in the 
specified DVR from the latest to the earliest. 
‧To quickly find the events you need, check or uncheck the event 
type “System” / “Manual” / “Alarm” / “Motion”, and select the log you 
want. 
‧To view the earlier or later logs that are not shown in the current 
page, click “Prev. Page” or “Next Page”.   
‧To refresh the event list, click “Reload”.   
File Path  Assign the location where the backup files are saved. 
Simultaneous Playback  To view the backup images simultaneously when the download 
process is in progress, select the checkbox “Simultaneous 
Playback”. You will see the backup images while the images are 
being downloaded to the PC or notebook. 
To simply backup images without previewing, deselect the 
checkbox “Simultaneous Playback”. You will only see a message 
box indicating the total time needed, the current status and the 
saving location. 
Download / Cancel  Click “Download” to start or “Cancel” to discard the video backup. 
  
						

							REMOTE OPERATION 
40 
Firmware Upgrade 
This function is used to grade your DVR for function scalability.   
Note: Before using this function, make sure you have the correct upgrade files 
provided by your installer or distributor. 
Step1: Click  “”, and select the IP address of your device in the address book.   
Step2: Click  “
” to show the upgrade page, “Update Server”. 
 
Step3: Click “Add” to browse to the upgrade files. 
 
Step4: Click “Upgrade Firmware” to start firmware upgrade. 
Note: It takes a few minutes to finish the upgrade process. Do not disconnect the 
power during firmware upgrade, or the upgrade may be failed. The device 
will reboot after the upgrade.  
Step5: Select the IP address of the device and click “” again to check if the 
firmware is upgraded. 
  
						

							REMOTE OPERATION 
41 
6.1.4. E-Map 
Video Viewer is also a Central Management System (CMS) software, which allows 
network device control & management for up to 16 devices simultaneously.   
Note: Before using this function, make sure Video Viewer is connected to all the 
devices (up to 16) you want to monitor. 
E-Map is ONLY available when the control panel is switch to the full function version.   
How to Add an E-Map Group 
STEP1: In the simplified version, click “” to switch the control panel to the full function 
version, and click “
” to enter the E-Map page as follows. 
Note: To know where the buttons are, please refer to “Simplified Version (Default) 
at page 35, and “Full Function Version” at page 36. 
 
STEP2: Right-click to show the shortcut menu on the top-left panel, and select the 
E-Map group you want to add. There are three E-Map groups you can add: 
Google E-MAP, Single E-MAP, and Building E-MAP.  
						

							REMOTE OPERATION 
42 
 
 
  
						

							REMOTE OPERATION 
43 
STEP3: When the E-Map group is created, you will see the tree on the top-left panel, 
showing all the devices you’ve added to this group.   
 
Icon Description 
 The connected device is camera. When it’s selected, it will become red. 
 The connected device is DVR. When it’s selected, it will become red. 
 For any motion or alarm event, it will appear on the screen to catch your 
attention.  
To know what’s happening quickly, double-click the device icon on the 
E-Map to show the live view. 
How to Edit / Remove an Existing E-Map Group 
¾  For Google E-Map Group 
Right-click on the group name to show the shortcut menu list, and select “Edit 
E-MAP” or “Remove E-MAP” as needed. 
You can also add a single E-Map group (Add Single E-MAP) or Building 
E-Map group (Add Building E-MAP) into the existing Google E-Map group.  
						

							REMOTE OPERATION 
44 
 
¾  For Single E-Map Group 
Right-click on the group name to show the shortcut menu list, and select “Edit 
E-MAP” or “Remove E-MAP” as needed. 
  
						

							REMOTE OPERATION 
45 
¾  For Building E-Map Group 
Right-click on the group name to show the shortcut menu list, and select “Edit 
Building E-MAP” or “Remove E-MAP” as needed. 
 
To edit or remove a certain level of the building E-Map group, right click on the 
level name, and select “Edit E-MAP” or “Remove E-MAP” as needed.