Samsung DLPTV HL-P5085W HL-P5685W User Manual

Adjusting the Picture Quality
The purpose of picture quality adjustment is to remove or reduce picture noise. If the noise is not
removed by fine tuning alone, then do the frequency adjustments to the utmost and fine tune
again. After the noise has been reduced, re-adjust the picture so that it is aligned on the center of
screen.
English - 81
1
Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the 
…or †button to
select “Setup”, then press the
ENTER button.
3
Press the …or †button...

Changing the Picture Position
After connecting the TV to your PC, adjust the position of picture if it is not well-aligned.
English - 82
PC Display
1
Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the 
…or †button to
select “Setup”, then press the
ENTER button.
3
Press the …or †button to
select “PC”, then press the
ENTER button.
4
Press the …or †button to
select “Position”, then press
the ENTER button.
5
Adjust the position of the
picture by pressing the
…/†/œ/√button.
Press the...

English - 83
Adjusting the Picture Quality and Position Automatically
This feature allows the TV to self-adjust to the incoming video signal. The values of fine, coarse
and position are adjusted automatically.
1
Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the 
…or †button to
select “Setup”, then press the
ENTER button.
3
Press the …or †button to
select “PC”, then press the
ENTER button.
4
Press the …or †button to
select “Auto Adjustment”,
then press the ENTER button.
The...

Initializing the Picture Settings
You can replace all picture settings with the factory default values.
English - 84
PC Display
1
Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the 
…or †button to
select “Setup”, then press the
ENTER button.
3
Press the …or †button to
select “PC”, then press the
ENTER button.
4
Press the …or †button to
select “Recall”, then press
the ENTER button.
The picture settings are
replaced with the factory
default values.
Press the EXIT button to exit....

English - 85
Changing the Picture Size (PC Mode)
You can select the picture size which best corresponds to your viewing requirements.
1
Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the 
…or †button to
select “Picture”, then press
the ENTER button.
Press the 
…or †button to
select “Size”, then press the
ENTER button.
3
Press the œor √button to
select the screen format you
want, then press the ENTER
button.
Press the EXIT button to exit.
Alternate method
Press the P.SIZE button on...

SAMSUNG
BP68-00352A-00(78~91)  6/18/04  4:29 PM  Page 86 

Appendix
BP68-00352A-00(78~91)  6/18/04  4:29 PM  Page 87 

Troubleshooting 
If the TV seems to have a problem, first try this list of possible problems and solutions. If none of
these troubleshooting tips apply, then call your nearest Samsung authorized service center.
English - 88
Appendix
Possible Solution
Try another channel.
Adjust the antenna.
Check all wire connections.
Try another channel.
Adjust the antenna.
Make sure the MUTE button is off.
Try another channel.
Press the SOURCE button.
Make sure the TV is plugged in.
Check the antenna connections.
Make...

Replacing the Lamp
• Why do I need to replace the lamp?
The lamp used in a projection TV has a limited lifespan. For the best screen quality it needs to
be replaced periodically. After replacing the lamp, the screen quality will be bright and clear
as new.
•Check before lamp replacement 
1. The lamp must be the same code number and type. 
2. The lamp type is indicated on the right side of the TV. It is also indicated on the lamp case. 
3. After checking the code number for the lamp, give the code number...

English - 90
Appendix
• For replacement, you will need a 5.91 Inches-long Phillips screwdriver and a pair of gloves.
NOTES
•Be sure the replacement Lamp is the same type.
•After replacing the lamp, align the lamp cover with the groove and secure the screws. 
•The TV will not turn on if the lamp cover is not correctly closed (as this will activate the
protective circuit).
1
Unplug TV, then remove the 7
screws.
2
Remove the rear cover.
3
Remove the 2 press-pin
screws the Lamp.
4
Separate the Lamp from the...