Samsung DLP TV HL-S5087W User Manual

English - 101
Setting up Your PC Software (Based on Windows XP)
The Windows display-settings for a typical computer are shown below. But the actual screens on your
PC will probably be different, depending upon your particular version of Windows and your particular
video card. But even if your actual screens look different, the same, basic set-up information will apply
in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.)
1. Right click the mouse on the Windows Desktop,...

PC Display
English - 102
NOTES
•The Modes Table conforms to the regulations of IBM/VESA and is prepared based on analog input
standards.
•The optimal resolution is 1920 x 1080 @ 60Hz.
•The optimal timing per each mode is the Vertical Frequency 60Hz. 
•Resolutions other than the resolutions above are not supported in PC mode.
Resolution
640 x 350
640 x 480
640 x 480
800 x 600
1024 x 768
1152 x 864
1280 x 960
1280 x 1024
1600 x 1200
1920 x 1200RB
Vertical Frequency [Hz]
70.086
59.94
72.809
75
60.317...

English - 103
Adjusting the Picture Quality
The purpose of picture quality adjustment is to remove or reduce picture noise. If the noise is not
removed by fine tuning alone, then do the frequency adjustments to the utmost and fine tune again.
After the noise has been reduced, re-adjust the picture so that it is aligned to the center of screen.
1Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the œor √button to select
“Setup”, then press the ENTER 
button.
3
Press the …or †button to...

PC Display
English - 104
Changing the Picture Position
After connecting the TV to your PC, adjust the position of the picture if it is not well-aligned.
1
Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the œor √button to select
“Setup”, then press the ENTER 
button.
3
Press the …or †button to select
“PC”, then press the ENTER button.
4
Press the …or †button to select
“Position”, then press the ENTER 
button.
5
Adjust the position of picture
by pressing the …/†/œ/√
button. 
Press...

1
Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the œor √button to select
“Setup”, then press the ENTER 
button.
3
Press the …or †button to select
“PC”, then press the ENTER button.
4
Press the …or †button to select
“Auto Adjustment”, then press the
ENTER button.
The picture quality and position are
automatically adjusted, and the
picture returns to original view
a few seconds later.
Select “Return” by pressing the 
…or † button, then press the ENTER
button to return to the...

PC Display
English - 106
Changing the Picture Size (PC Mode)
You can select the picture size which best corresponds to your viewing requirements.
1
Press the SOURCE button to select “PC”.
2
Press the MENU button. 
Press the œor √button to select
“Picture”, then press the ENTER 
button.
Press the …or †button to select
“Size”, then press the ENTER button.
3
Press the …or †button to select the
screen format you want, then press
the ENTER button.
Select “Return” by pressing the …or † button, then press the...

English - 107
Viewing the Current Resolution
You can get the resolution information of your PC.
1
Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the œor √button to select
“Setup”, then press the ENTER 
button.
3
Press the …or †button to select
“PC”, then press the ENTER button.
The resolution information is
displayed on the screen.
Select “Return” by pressing the 
…or † button, then press the ENTER
button to return to the previous menu.
Press the EXIT button to exit.
NOTE
•To...

PC Display
English - 108
Initializing the Picture Settings
You can replace all picture settings with the factory default values.
1
Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the œor √button to select
“Setup”, then press the ENTER 
button.
3
Press the …or †button to select
“PC”, then press the ENTER button.
4
Press the …or †button to select
“Image Reset”, then press the ENTER
button.
The picture settings are replaced with
the factory default values.
Select “Return” by pressing...

WISELINK
BP68-00588A-00Eng(100~109)  3/3/06  10:58 AM  Page 109 

WISELINK
English - 110
Using the WISELINK Function 
This function enables you to view and listen to photo (JPEG) and audio files (MP3)saved on a USB
Mass Storage Class (MSC) device.
Press the power button on the
remote control or front panel.
Connect a USB device containing
JPEG and/or MP3 files to the
WISELINK jack (USB jack) on the
side of the TV first.
TV Side Panel
NOTES
•If you enter the WISELINK mode with no USB device connected. “There is no device connected”
message will appear. In this case,...