Samsung Dcs 400si Lcd24b, Lcd12b, Std24b, Basic 12b, 7b Keyset User Guide

Reply by speaking in the direction of the microphone in the AOM unit.
Adjust the volume with the VO L keys on the AOM unit.
Press the SPK or the MONITOR key on the AOM to disconnect the an-
nouncing party.
NOTES:
1. Executive off-hook voice announce can only be accomplished when an AOM
is attached to your phone.
2. If the MUTE key on the AOM is lit, you must press the AOM’s SPK key to
answer the OHVA call.OHVA BLOCKYour keyset can be programmed with an OHVA Block (BLOCK) key. Pressing
this key will...

Redial the new passcode to verify. If successful, you will hear two beeps.
Four beeps indicate an incorrect code. Reenter the code again.
Press TRSF to store the new passcode.SET ANSWER MODEYou can receive internal calls in one of three modes (see 
Answering Intercom
Calls
 under 
Intercom Calls
 for descriptions):
While on-hook, press TRSF and then dial 103.
Dial 0 for Ringing, 1 for Auto Answer or 2 for Voice Announce.
Press TRSF to store your selection.
NOTE: When your keyset is programmed for...

DISPLAY FEATURES
INTERACTIVE DISPLAY KEYSThe three keys below the display are substitutes for dedicated feature keys and
access codes. Pressing one of these keys has the same effect as pressing a
programmable key. These keys are called soft keys as their functions are not
fixed. They change to present you with the best options for that call condition.
The use of soft keys allows the programmable keys to be used for more DSS
and speed dial keys.
The SCROLL key is used to display options available to the...

CALL DURATION TIMERThe system can be set to automatically time outside calls. A few seconds after
you dial a telephone number, the timer appears in the display. It appears imme-
diately for incoming calls. The call timer continues for the duration of the call.
Call duration times are displayed in minutes and seconds. If a call lasts longer
than 60 minutes, the timer restarts.
You can press the TIMER key to manually begin timing a call. Press it again to
stop timing. If you press it while the automatic...

Press TRSF and then dial 106.
Dial the speed dial bin number 00–49.
Write your message using the procedure described in 
Alarm Reminder Mes-
sages
.
Press the TRSF key to store the speed dial name.
Repeat for each speed dial bin if necessary.
STATION NAMESYou can assign an 11 character name to your keyset. This allows other display
keyset users to call you using the directory dial feature.
To program a station name:
Press TRSF and then dial 104.
Enter the 11 character name using the procedure...

WHAT IS ANI?ANI (Automatic Number Identification) is a feature offered by some telephone
service providers that provides the calling party’s telephone number. This ser-
vice is only available on E&M Tie Lines on a T1, digital trunk. ANI is similar to
Caller Identification (CID) but the format and information of the calling person is
different. CID uses FSK signalling and ANI uses DTMF signalling. Usually, with
ANI, a calling party’s identity is the Listed Directory Number (LDN) unless a
separate...

48 NOTES:
1. If you are on an intercom call or you have Automatic Hold turned off, you
must finish the existing call or place it on hold before inquiring.
2. If you inquire about an outgoing call, you will receive a [call no longer avail-
able] display.REVIEWING PAST CID/ANI CALLSThis feature allows you to review CID information for calls sent to your keyset.
This list can contain 10–50 calls in a last-in, first-out basis. The list includes
calls that you answered and calls that rang your keyset but that...

The example on the following page will better demonstrate how to use Text
Messaging. In this example station 205 is making an off hook voice announce-
ment to station 205 who after hearing the announcement will respond with a text
message.
STATION 201: LINDA STATION 205: JOHN
received a call on line 702 is talking on line 701
Talking on line 702
 702:         01:15 701:         05:25
 CONF   PAGE   MUTE
Press TRANSFER
 Transfer:
 RETURN
Dial 205
 205:busy
   OHVA     CAMP ON
   OHVA to 205    OHVA from...

PERSONAL SPEED DIAL NUMBERS
CODE NAMETELEPHONE NUMBER
00 _________________________ _________________________
01 _________________________ _________________________
02 _________________________ _________________________
03 _________________________ _________________________
04 _________________________ _________________________
05 _________________________ _________________________
06 _________________________ _________________________
07 _________________________ _________________________
08...

S
YSTEM
 A
CCESS
 C
ODES
PAGING ZONES
 - Dial 55 plus
0 ALL INTERNAL ZONES
1 ____________________
2 ____________________
3 ____________________
4 ____________________
5 ____________________
6 ____________________
7 ____________________
8 ____________________
9 ALL EXTERNAL ZONES
✱ALL PAGE
FEATURE ACCESS CODE10  +  xxx PICK UP A PARKED CALL
12  +  xxx PICK UP A HELD CALL
13 DOOR LOCK RELEASE
16 + xxx SPEED DIALING
17 SAVE AND REDIAL NUMBER
18 NEW CALL (RECALL)
19 LAST NUMBER REDIAL
400 CANCEL DO NOT...