Samsung CLX 6250FX User Manual

Basic setup_ 3
Correcting numbers or names
If you make a mistake while entering a number or name, press the left/right 
arrow button to delete the last digit or character. Then enter the correct 
number or character.
Inserting a pause
With some telephone systems, you must dial an access code (9, for 
example) and listen for a second dial tone. In such cases, you must insert a 
pause in the telephone number. You can insert a pause while you are 
setting up speed dial numbers.
To insert a pause, press...

Basic setup_ 4
4.Press the up/down arrow to highlight Paper Size and press OK.
5.Press the up/down arrow to select the paper tray you want and press 
OK.
6.Press the up/down arrow to select the paper size you want.
7.Press OK to save the selection.
8.Press Stop/Clear to return to ready mode.
Setting the paper type
1.Press Menu on the control panel.
2.Press the up/down arrow to highlight System Setup and press OK.
3.Press the up/down arrow to highlight Paper Setup and press OK.
4.Press the up/down arrow...

Media and tray_ 1
1.media and tray
This chapter provides information on how to l oad originals and print media into your machine.
This chapter includes:
•Preparing originals
• Loading originals
• Selecting print media
• Changing the tray size •
Loading paper in the tray
• Printing on special media
• Setting the paper size and type
• Selecting an output location
  
Preparing originals
•Do not load paper smaller than 142 x 148  mm (5.6 x 5.8  inches) or 
large
r than 216 x 356  mm (8.5 x 14  inches). 
• Do...

Media and tray_ 2
 
•Be careful not to break the scanner glass. You may get hurt.
• Do
 not put hands while closing the scanner lid. The scanner lid 
may fall on your hands and get hurt.
• Do
 not look the light from inside of the scanner while copying or 
scanning. It is harmful to eyes.
In the document feeder
Using the document feeder, you can load up to 40  sheets of paper (80  g/m2, 
20  lb bond) for one job. 
1. Fle
x or fan the edge of the paper  stack to separate the pages before 
loading...

Media and tray_ 3
Changing the tray size
The tray is preset to Letter or A4 size, depending on your country. To 
change the size, you need to adjust the paper guides.
1Tray extend lever
2Paper length guide
3Paper width guide
1. Hold the tray with one hand, and wit h the other hand squeeze and slide 
the paper length guide to locate them in the correct paper size slot 
marked at the bottom of the tray.
2. Flex or fan the edge of the paper  stack to separate the pages before 
loading papers.
3. After...

Media and tray_ 4
Paper quantity indicator shows the  amount of paper in the tray. 
1Full
2Empty
4. When you print a document, set the paper type and size for the tray.
For information about setting the paper type and size on the control 
pan
 el (See  Setting the paper size and type on page  7 ).
 •If you experience problems with p aper feeding, check whether the 
paper meets the media specific ation. Then, try placing one 
sheet at a time in the  multi-purpose tray (See  Print media 
specifications on...

Media and tray_ 5
5.When you print a document, set the paper type and size for the 
multi-purpose tray.
For information about setting the pa per typ
 e and size on the control 
panel (See  Setting the paper size and type on page  7 ).
 The settings made from the machine driver override the 
settings on the control panel.
a) T
o print in application, open an  application and start the print 
menu.
b) Open  Printing
  Preferences (See  Opening printing 
preferences on page  2).
c)Pr
ess the  Paper tab in...

Media and tray_ 6
1 Acceptable
2 Unacceptable
• Envelopes with a peel-off adhesive strip  or with more than one flap that 
folds over to seal must use adhesives compatible with the machine’s 
fusing temperature about 170°C (338 °F) for 0.1 second. The extra flaps 
and strips might cause wrinkling,  creasing, or jams and may even 
damage the fuser.
• For the best print qual
 ity, position margins no closer than 15  mm from 
th
e edges of the envelope.
• Avo
id printing over the area where the envelope’s...

Media and tray_ 7
machine’s fusing temperature for 0.1 second. Check your machine’s 
specification to view the fusing  temperature about 170°C(338 °F). 
• Used pa
 per ink must be non-flammabl e and should not adversely affect 
machine rollers.
• Before you loa
 d used paper, verify that the ink on the paper is dry. 
During the fusing process, wet ink can come off used paper, reducing 
print quality.
Photo
• Make sure not to use the inkjet phot o paper with this machine. It could 
cause damage to the...

Media and tray_ 8
For Letter-sized paper
Pull out the output support to the location indicated LTR as shown, and 
unfold the extension.
For A4- or Lega l-sized paper
Pull out the output support to the location indicated A4, LGL as shown, and 
unfold the extension.
Downloaded From ManualsPrinter.com Manuals