Samsung CLP 660ND User Manual

8.1   
8 Ordering supplies and 
accessories
This chapter provides information on purchasing cartridges and 
accessories available for your machine.
This chapter includes:
• Supplies
• Accessories
• How to purchase
Supplies
When the toner runs out, you can order the following type of toner 
cartridge for your machine:
Caution
When you purchase a new toner ca rtridge or supplies, you must 
purchase them in the same country you have purchased your 
machine. Otherwise, the toner cartridge or supplies will...

9.1   
9 Installing accessories
Your machine is a full-featured mode l that has been optimized to meet 
most of your printing needs. Recognizing that each user may have 
different requirements, however,  Samsung makes several accessories 
available to enhance your machine’s capabilities.
This chapter includes:
• Precautions to take when installing accessories
• Installing a memory module
Precautions to take when installing accessories
• Disconnect the power cord
Never remove the control board cover...

9.2   
6 Replace the control board cover and fasten the cover with the 
screw.
7 Reconnect the power cord and printer cable, and turn the machine 
on.
Note
To release the memory module, pull the two tabs on the 
sides of the slot outwards, then the module springs out. 
Activating the added memory in the PS printer 
properties
After installing the memory module, you need to select it in the printer 
properties of the PostScript printer driv er in order to use it. This activation 
is needed only the...

10.1   
10 Specifications
This chapter includes:
• CLP-610 Series
• CLP-660 Series
Note
The numbers herein is subject to change according to its install 
environment.
CLP-610 Series
ItemSpecifications and Description
Printing speed
aUp to 20 ppmb (A4), 21 ppm (Letter)
Duplex printing 
speed
Up to 9.86 ipmc (A4, Letter)
Printing resolution
Max. 2,400 x 600 dpi effective output
Warm-up time
Less than 40 seconds
First print out time
20 seconds (from Ready mode)
Consumables life
Standard yield 
toner...

10.2   
CLP-660 Series
Note
The symbol * denotes an optional feature depending on 
machines.   
a. Printing speed: it will be affected by operating system used, computing 
performance, application software, connec ting method, media type, media size, 
and job complexity.
b. ppm: page per minute.
c. ipm: image per minute.
d. Declared yield value in accordance with ISO/IEC 19798.
e. It varies depending on the product configuration.
f. Noise Level: sound pressure level, ISO 7779.
ItemSpecifications and...

10.3   
a. Printing speed: it will be affected by operating system used, computing 
performance, application software, connecting method, media type, media 
size, and job complexity.
b. ppm: page per minute.
c. ipm: image per minute.
d. Declared yield value in accordance with ISO/IEC 19798.
e. It varies depending on the product configuration.
f. Noise Level: sound pressure level, ISO 7779.
Downloaded From ManualsPrinter.com Manuals 

11.1   
11 Glossary
BOOTP
It stands for Bootstrap Protocol, a  network protocol used by a network 
client to obtain its IP address automatically. This is usually done in the 
bootstrap process of computers or  operating systems running on them. 
The BOOTP servers assign the IP address from a pool of addresses to 
each client. 
Control Panel
A control panel is a flat area where co ntrol or monitoring instruments are 
displayed. They are typically found  in top or front of the machine. 
Coverage
This is...

11.2   
ISO
The International Organization for Standardization (ISO) is an 
international standard-setting body  composed of representatives from 
national standards bodies. It produces world-wide industrial and 
commercial standards.
LED
A light-emitting diode (LED) is a semiconductor device that indicates the 
status of a machine. 
Print Media
Media such as papers, envelopes, labels, and transparencies which can 
be used on a printer, a scanner, a fax or, a copier. 
OPC Drum
A mechanism that makes a...

1
B
Back 1.4
C
cleaninginside 6.1
outside 6.1
control panel 1.2, 1.4
D
default settings loading paper 3.5
tray setting 3.5
Display 1.4
driver
feature 2.1
installation 3.3
E
energy saver 3.5
error message 7.7
F
front cover 1.2
front cover handle 1.2
J
jamclearing paper from the tray1 7.1
tips for avoiding paper jams 7.1
L
language 3.4
LEDStatus 1.5
Left/right arrows 1.4
Linux problems 7.16
requirements 2.2
M
Macintoshproblems 7.16
requirements 2.2
Maintenance 6.1
maintenance parts 6.7
toner cartridge...

2
U
USBport 1.3
W
Windows
problems 7.15
requirements 2.2
Downloaded From ManualsPrinter.com Manuals