Samsung CLP 650N User Manual

Solving Problems
7.15
Engine Fuser
Low Heat ErrorThe temperature in 
the fuser is abnormally 
low. Unplug the power cord and 
plug it in again. If the problem 
persists, call for service.
Engine Fuser
Over Heat Error The temperature in 
the fuser is abnormally 
high. Unplug the power cord and 
plug it in again. If the problem 
persists, call for service.
Engine Fuser
Inverter Error A problem has 
occurred in the Fuser 
in the printer. Unplug the power cord and 
plug it in again. If the problem 
persists,...

Solving Problems
7.16
Press 
Continue ButtonThe printer is waiting 
for the user’s action 
before printing from 
the Multi-purpose Tray 
using the manual feed 
mode. Load a sheet of print material 
and press the 
On Line/
Continue
 button. You need to 
press the button for each page.
Ready [Color]
Low Toner The corresponding 
toner cartridge in your 
printer is low on toner. Redistribute the toner in the 
corresponding toner cartridge, 
referring to page 6.2.
Ready
IP Conflict The IP address of the...

Solving Problems
7.17
Common Windows Problems
NOTE: Refer to the Microsoft Windows 98SE/Me/NT 4.0/2000/
2003/XP User’s Guide that came with your PC for further 
information on Windows error messages.
Common Macintosh Problems
ProblemPossible Cause and Solution
“File in Use” message 
appears during 
installation. Exit all software applications. Remove all software 
from the StartUp Group, then restart Windows. 
Reinstall the printer driver.
“Error Writing to LPTx” 
message appears. • Ensure that all...

Solving Problems
7.18
Common Linux Problems
“Limit Check 
Error” message 
appears.The print job was too 
complex.
You might need to reduce the 
complexity of the page or 
install more memory.
MessageStatusDo this...
ProblemPossible Cause and Solution
I can’t change settings 
in the configuration 
tool.You need to have administrator privileges to be able 
to change global settings.
I am using the KDE 
desktop but the 
configuration tool and 
LLPR won’t start. You may not have the GTK libraries installed....

Solving Problems
7.19
How do I specify the 
IP address of my SMB 
server?It can be specified in the “Add Printer” dialogue of 
the configuration tool, if you don’t use the CUPS 
printing system. Unfortunately, CUPS currently 
doesn’t allow you to specify the IP address of SMB 
printers, so you will have to be able to browse the 
resource with SAMBA in order to be able to print.
Some documents 
come out as white 
pages when printing. Some versions of CUPS, especially those shipped 
with Mandrake Linux...

Using Your Printer on a Network (CLP-650N only)
8.1
8Using Your Printer on a 
Network (CLP-650N only)
If you work in a networked environment, the printer can be 
shared by other users on the network.
This chapter includes:
• About Sharing the Printer on a Network
• Setting Up a Network-Connected Printer
About Sharing the Printer on a 
Network
If you work in a networked environment, you can connect your 
printer to the network.
Locally-Shared Printer
You can connect the printer directly to a selected...

Using Your Printer on a Network (CLP-650N only)
8.2
Printing a Network Configuration Page
The Network Configuration page shows how the network 
interface card on your printer is configured. The default settings 
which are suitable for most applications are enabled. 
1In ready mode, press the Menu button ( ) until you see 
“Network” on the bottom line of the display.
2Press the Enter button ( ) to access the menu.
3Press the scroll button (  or  ) until “Print Net CFG” 
displays on the bottom line.
4Press...

Using Your Printer on a Network (CLP-650N only)
8.3
13Repeat step 12 to complete the address from the 1st byte 
to the 4th byte.
14To select other parameters, such as the Subnet Mask or 
Gateway, press the scroll button (  or  ). Press the 
Enter button ( ).
15Repeat steps 12 through 13 to configure the other TCP/IP 
parameters.
16Press the On Line/Continue button ( ) to return to 
ready mode.
Dynamic Addressing (BOOTP/DHCP)
To assign the TCP/IP address automatically by the server, take 
the following...

Using Your Printer on a Network (CLP-650N only)
8.4
12Press the scroll button (  or  ) until you see the 
desired frame type and press the 
Enter button ( ). 
13Press the On Line/Continue button ( ) to return to 
ready mode.
Restoring the Network Configuration
You can return the network configuration to its default settings.
1In ready mode, press the Menu button ( ) until you see 
“Network” on the bottom line of the display.
2Press the Enter button ( ) to access the menu.
3Press the scroll button (  or...

Installing Printer Options
9.1
9Installing Printer 
Options
Your printer is a full-featured laser printer that has been 
optimized to meet most of your printing needs. Recognizing 
that each user may have different requirements, however, 
Samsung makes several options available to enhance the 
printer’s capabilities.
This chapter includes:
• Precautions When Installing Printer Options
• Installing an Optional Paper Tray
• Installing a memory DIMM
Precautions When Installing 
Printer Options
DISCONNECT...