Samsung CLP 610ND User Manual

							
iv
Canadian Radio Interference Regulations
This digital apparatus does not exceed the Class B limits for radio noise 
emissions from digital apparatus as  set out in the interference-causing 
equipment standard entitled  “Digital Apparatus”, ICES-003 of the Industry 
and Science Canada.
Cet appareil numérique respecte les limites de bruits radioélectriques 
applicables aux appareils numériques de  Classe B prescrites dans la norme 
sur le matériel brouilleur: “Appareils Numériques”, ICES-003 édictée par 
l’Industrie et Sciences Canada.
Declaration of  Conformity (European Countries)
Approvals and Certifications
The CE marking applied to this product symbolizes 
Samsung Electronics Co., Ltd.  Declaration of Conformity 
with the following applicable  93/68/EEC Directives of the 
European Union as of the dates indicated:
January 1, 1995: Council Directive 73/23/ EEC Approximation of the laws of 
the member states related to low voltage equipment.
January 1, 1996: Council Directive  89/336/EEC (92/31/EEC), approximation 
of the laws of the Member States re lated to electromagnetic compatibility.
March 9, 1999: Council Directiv e 1999/5/EC on radio equipment and 
telecommunications terminal equipment  and the mutual recognition of their 
conformity.
A full declaration, defining the relev ant Directives and referenced standards 
can be obtained from your Samsung Elec tronics Co., Ltd. representative.
Replacing the Fitted Plug (for UK Only)
Important
The mains lead for this machine is fitted with a standard (BS 1363) 13 amp 
plug and has a 13 amp fuse. When you change or examine the fuse, you 
must re-fit the correct 13 amp fuse. Y ou then need to replace the fuse cover. 
If you have lost the fuse cover, do not use the plug until you have another fuse 
cover. 
Please contact the people from you purchased the machine.
The 13 amp plug is the most widely used type in the UK and should be 
suitable. However, some buildings  (mainly old ones) do not have normal 13 
amp plug sockets. You need to buy a su itable plug adaptor. Do not remove 
the moulded plug.
Warning
If you cut off the moulded plug, get rid of it straight away.
You cannot rewire the plug and you may receive an electric shock if you 
plug it into a socket.
Important warning: You must earth this machine.
The wires in the mains lead have the following color code:
• Green and Yellow:  Earth
• Blue: Neutral
•Brown: Live
If the wires in the mains lead do not ma tch the colors marked in your plug, do 
the following:
You must connect the green and yellow wire  to the pin marked by the letter 
“E” or by the safety ‘Earth symbol’ or colored green and yellow or green.
You must connect the blue wire to the pi n which is marked with the letter “N” 
or colored black.
You must connect the brown wire to the pin which is marked with the letter “L” 
or colored red.
You must have a 13 amp fuse in the pl ug, adaptor, or at the distribution board.
OpenSSL License
Copyright (c) 1998-2001 The OpenSSL Project. All rights reserved.
Redistribution and use in source an d binary forms, with or without 
modification, are permitt ed provided that the following conditions are met:
Redistributions of source code must reta in the above copyright notice, this list 
of conditions and the  following disclaimer. 
Redistributions in binary form must r eproduce the above copyright notice, this 
list of conditions and the following di sclaimer in the documentation and/or 
other materials provided  with the distribution.
All advertising materials m entioning features or use of this software must 
display the following acknowledgment : This product includes software 
developed by the OpenSSL Project for us e in the OpenSSL Toolkit. (http://
www.openssl.org/)
The names OpenSSL Toolkit and Open SSL Project must not be used to 
endorse or promote products derived from this software without
prior written permission. For writt en permission, please contact openssl-
[email protected].
Products derived from this software may not be called OpenSSL nor may 
OpenSSL appear in their names without  prior written permission of the 
OpenSSL Project.
Redistributions of any form whats oever must retain the following 
acknowledgment: This product incl udes software developed by the 
OpenSSL Project for use in the Open SSL Toolkit (http://www.openssl.org/)
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT ``AS IS 
AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT 
NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY 
AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO 
EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE 
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, 
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT 
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; 
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE 
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS 
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH 
DAMAGE.
This product includes cryptographic software written by Eric 
Young([email protected]). This product includes software written by Tim 
Hudson ([email protected]).
Downloaded From ManualsPrinter.com Manuals 
						

							
v
Original SSLeay License
Copyright (C) 1995-1998 Eric Young ([email protected]) All rights 
reserved.
This package is an SSL implementation written by Eric Young 
([email protected]). The implementation was written so as to conform with 
Netscapes SSL.
This library is free for commercial and non-commercial use as long as the 
following conditions are aheared to. The  following conditions apply to all code 
found in this distribution, be  it the RC4, RSA, lhash, DES, etc., code; not just 
the SSL code. The SSL documentation  included with this distribution is 
covered by the same copyright terms except that the holder is Tim Hudson 
([email protected]). Copyright remains Eric Youngs, and as such any 
Copyright notices in the code are not to  be removed. If this package is used 
in a product, Eric Young should be given at tribution as the author of the parts 
of the library used. This can be in t he form of a textual message at program 
startup or in documentation (online or  textual) provided with the package.
Redistribution and use in source and  binary forms, with or without 
modification, are permitted provided t hat the following conditions are met:
Redistributions of source code must reta in the copyright notice, this list of 
conditions and the fo llowing disclaimer.
Redistributions in binary form must r eproduce the above copyright notice, this 
list of conditions and the following  disclaimer in the documentation and/or 
other materials provided  with the distribution.
All advertising materials m entioning features or use of this software must 
display the following acknowledgement: This product includes cryptographic 
software written by Eric Young ([email protected]) The word 
cryptographic can be left out if the  rouines from the library being used are 
not cryptographic related:-). 
If you include any Windows specific c ode (or a derivative thereof) from the 
apps directory (application code) y ou must include an acknowledgement: 
This product includes software written by Tim Hudson ([email protected])
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ``AS IS AND ANY 
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED 
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS 
FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN NO EVENT SHALL 
THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, 
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR 
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON 
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 
LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF 
ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
The licence and distribution terms for  any publically available version or 
derivative of this code cannot be changed.  i.e. this code cannot simply be 
copied and put under another  distribution licence [including the GNU Public 
Licence.]
Downloaded From ManualsPrinter.com Manuals 
						

							
1.1   
1 Introduction
Thank you for purchasing this Samsung color printer. 
This chapter includes:
• Special features
• Machine overview
• Control panel overview
• Understanding the Status LED
• Understanding the menu map
Note
Some features are optional . Check the specifications 
sections. (See Specific ations on page 10.1.)
Special features
Your new machine is equipped with special features.
Print with excellent quality and speed
• You can print in a full range of colors using cyan, magenta, yellow, and black.
• You can print up to 2400 x 600 dpi effective output. See 
Software section.
• Your machine prints A4-sized paper at up to 20 ppma  
(CLP-610 series), 24 ppm (C LP-660 series) and letter-
sized paper at up to 21 ppm (CLP-610 series), 25 ppm 
(CLP-660 series).
Handle different paper options with flexibility •The multi-purpose tray  supports letterhead, 
envelopes, labels, custom-s ized media, postcards, and 
heavy paper. The  multi-purpose tray  holds up to 100 
sheets of plain paper for the CLP-610ND and CLP-660 
series.
•The  250-sheet tray 1  and 500-sheet optional tray  
support plain paper in various sizes. 
Create professional documents •Print Watermarks . You can customize your documents 
with words, such as “Confidential”. See 
Software 
section.
•Print  Posters . The text and pictures of each page of 
your document are magnified and printed across the 
sheet of paper and can then be taped together to form 
a poster. See 
Software section.
• You can use preprinted forms and letterhead with plain  paper. See 
Software section.
Save time and money
Expand your machine’s capacity
* Zoran IPS Emulation compatible with PostScript 3 
© Copyright 1995-2005, Zoran Corporation. All rights 
reserved. Zoran, the Zoran logo, IPS/PS3, and 
OneImage are trademarks of Zoran Corporation.
* 136 PS3 fonts
Contains UFST and MicroType from Monotype Imaging Inc.
Print in various environments • To save paper, you can print multiple pages on one 
single sheet of paper.
• This machine automatically  conserves electricity by 
substantially reducing power consumption when not in 
use.
• To save paper, you can print on both sides of the paper  (double-sided printing). Th is feature is supported 
depending on the models. See 
Software section.
• Your machine has an extra memory slot to expand their  memory. (Page 8.1)
• Zoran IPS Emulation* compatible with  PostScript 3 
Emulation * (PS) enables PS printing. 
• You can print with  Windows 2000/XP/2003/Vista  as 
well as  Linux and Macintosh  systems.
• Your machine is equipped with a  USB interface and a 
network  interface.
a. pages per minute
b. images per minute
Downloaded From ManualsPrinter.com Manuals 
						

							
1.2   
Machine overview
These are the main components of your machine.
Front view 
• The figure above shows your machine with the availabl e accessories. (See page 8.1 for more information)
• The symbol 
* denotes an optional device.
Note 
• All illustrations on this user’s guide may differ from your machine depending on its options or models.
• The surface of the output tray may become  hot if you print a large number of pages at once. Make sure that you do not touch the surface, and do 
not allow children near it.
1output tray7multi-purpose tray
2output support8tray 1
3control panel9optional tray*
4front cover10 paper level indicator
5front cover handle11multi-purpose tray paper width guides
6multi-purpose tray handle
Downloaded From ManualsPrinter.com Manuals 
						

							
1.3   
Rear view 
• The figure above shows your machine with the available accessories.
• The symbol * denotes an optional device.
1
USB port5power switch
2network port6power receptacle
315-pin Optional tray connection*7control board cover  (Memory module, see page 9.1 for 
more information)
4 handle  (Use these handles to move your machine.)
Downloaded From ManualsPrinter.com Manuals 
						

							
1.4   
Control panel overview
1
Display : Shows the current status and prompts during an 
operation.5 Left/right arrow : Navigates available values by moving to the next 
or previous options.
2 Toner colors : The toner colors shown below the LCD display work 
together with the display messages.  See Status LED with the toner 
cartridge messages on page 1.5.6 OK: Confirms the selection on the display.
3Status: Shows the status of your machine. (See Understanding the 
Status LED on page 1.5 for more information.)7 Back: Sends you back to the upper menu level.
4
Menu : Enters Menu mode and scrolls through the available menus. 
(See Understanding the Status LED on page 1.5 for more 
information.)8 Stop: Stops an operation at any time. 
Downloaded From ManualsPrinter.com Manuals 
						

							
1.5   
Understanding the Status LED
The color of the  Status LED indicates the mach ines current status.
Note 
Always check the message on the di splay to solve the problem. 
The instruction in the Troubleshooting section will guide you to 
operate the machine properly. See page 7.1 for more 
information.
StatusDescription
Off • The machine is powered off.
Green Blinking • When the green LED slowly blinks, the  machine is receiving data from the computer.
• When the green LED blinks rapidly, the 
machine is printing data. 
On • The machine is powered on and can be used. • The machine is in power save mode. When data is received, it switches to the ready mode 
automatically.
Red Blinking • A minor error has occurred and the machine  is waiting for the error to be cleared. Check 
the display message, and solve the problem 
referring to Understanding display 
messages on page 7.7. 
• The toner cartridge is low. Order a new toner  cartridge, see Ordering supplies and 
accessories on page 8.1. You can 
temporarily improve print quality by 
redistributing the toner. See Replacing the 
toner cartridge on page 6.4.
On • A problem has occurred such as a paper jam,  opened cover or no paper in the tray, so that 
the machine can not continue the job. Check 
the message on the display, and refer to 
Understanding display messages on page 7.7 
to solve the problem.
• The toner cartridge is empty, exhausted, or 
needs to be changed. See Understanding 
display messages on page 7.7.
Status LED with the toner cartridge messages
The status of toner cartridges is indicated by the status LED and the LCD 
display. If the toner cartridge is low or needs to be changed, the status 
LED turns red and the display show s the message. However the arrow 
mark (or marks) shows which color toner is of concern or may be installed 
with a new cartridge. 
Example: 
The above example shows the magenta  toner cartridge status indicated 
by the arrow. Check the message to find out what the problem is and how 
to solve it. See page 7.7 to browse the detailed information on error 
messages.
Downloaded From ManualsPrinter.com Manuals 
						

							
1.6   
Understanding the menu map
The control panel provides access to various menus to set up the 
machine or to use the machines functions. Refer to the following 
diagram. 
Accessing menus
The next steps show how to print the menu map of this machine, and they 
are the general way to select menus and configure your machine.
1 Make sure your machine is properly connected with all the 
necessary cables, and turn on the machine.
2 Press  Menu on the control panel, until  you see the menu (ex. 
Information) you want on the bottom line of the display.
3 Press  OK to access the menu.
4 Press left/right arrow  until the menu item (ex.  Menu Map) you want 
displays on the bottom line.
5 Press the  OK button to confirm the selected item.
Note 
If the menu item has sub  menus, repeat steps 4 and 5.
6 Press left/right arro w until the menu item (ex. Print?) you want 
displays on the bottom line.
7 Press  OK to process your selection,  save your input or selection.
An asterisk (*) appears next to the selection on the display, 
indicating that it is now the default.
8 To exit the menu, press  Back repeatedly, or  Stop.
Note 
• If no key is pressed within one minute, the machine 
automatically return s to ready mode.
• The print settings made from the printer driver on a connected  computer override the se ttings on the control panel.
Menu overview
Information
Menu Map
Configuration
Demo Page
PCL Font List
PS Font List
Layout
Orientation
Simplex Margin
Duplex
Duplex Margin
System Setup
Language
Power Save
Auto Continue
Altitude Adj.
Auto CR
Job Timeout
Maintenance
Clear Setting
Emulation
Emulation Type
Setup
Network
TCP/IP
Ethernet Speed
Clear Setting
Network Info.
Color
Custom Color
Auto Color Reg.
Graphic
Resolution
Paper
Copies
Paper Size
Paper Type
Paper Source
Tra y  C h a i n i n g
Downloaded From ManualsPrinter.com Manuals 
						

							
1.7   
Description on each menu
The following tables provide the information on each menu.
Note 
The symbol * denotes an optional menu depending on 
machines.
Information 
Layout 
MenuDescription
Menu Map You can print the menu map which shows the 
layout and current settings of this machine.
Configuration You can print the machines current 
configuration. 
Demo Page The demo page is a sample of the machine’s 
imaging capabilities.
PCL Font List * You can print the PCL font list.
PS Font List * You can print the PS font list.
MenuDescription
Orientation This menu allows you to select the direction in 
which information is printed on a page. 
Landscape and Portrait  are selectable. 
Simplex Margin Set the margin of print materials for one-sided 
printing. You can increase or decrease the value 
in 1 mm (or inch) increments.
•To p  M a r g i n : Set the top margin.
• Left Margin : Set the left margin.
LandscapePortrait
Paper 
Duplex* To print on both sides of paper, choose the 
binding edge as follows.
•Long Edge : Flip on the long edge.
• Short Edge : Flip on the short edge.
Select  Off to print on one side of the paper.
Duplex Margin * In this menu, you can set the margins for double-
sided printing. You can increase or decrease the 
value in 0.1 mm increments.
•To p  M a r g i n : Set the top margin.
• Left Margin : Set the left margin.
• Short Binding : Set the bottom margin of the 
back of the page for short binding.
• Long Binding : Set the right margin of the 
back of the page for long binding.
MenuDescription
Copies You can select the maximum amount of copies.
Paper Size You can select the default paper size. (See page 
3.5 for more information)
Paper Type You can select the default paper type for the 
print media.
MenuDescription
Long Edge in the 
Landscape orientationLong Edge in the 
Portrait orientation
Short Edge in the 
Landscape orientationShort Edge in the 
Portrait orientation
Downloaded From ManualsPrinter.com Manuals 
						

							
1.8   
Graphic 
System Setup 
Paper Source You can select the tray to process the print job. If 
you select Auto, your machine supplies the 
paper from the multi-pur pose tray first, then the 
tray 1, and tray 2 for the last. So if any tray is 
empty, then the machine tries to search the 
paper from the next available tray. (See page 3.5 
for more information)
Tray Chaining When you select any  other value except Auto 
from  Paper Source  and the selected tray is 
empty, you can set the machine to automatically 
print from other trays.
If this menu item is set to  Off, the machine does 
not print until you insert paper into the specified 
tray.
MenuDescription
Resolution You can select the default resolution. If the 
resolution is high, the clarity of the printouts is 
sharper, but the print time may take longer.
•Draft : If the printer language is PCL and your 
print jobs are text, select this option for the 
best speed and printing quality. This option is 
available only with PCL driver.
• Normal : If your print jobs are mostly text, 
select this option for the highest quality output.
• Best : select this option when your job contains 
bitmapped images, such as scanned photos or 
certain business graphics, that will benefit 
from enhanced line screening.
MenuDescription
Language The language setting for the display on the 
control panel determines the language of the text 
that appears on the control panel display and for 
printing information. (See page 3.4 for more 
information)
Power Save When the machine does not receive data for an 
extended period of time, power consumption is 
automatically lowered. You can set how long the 
machine waits before going to power save. (See 
page 3.5 for more information)
MenuDescription
Emulation 
Auto Continue This item determines whether or not the machine 
continues printing when it detects paper that is 
not matched to your paper setting.
•Off : If a paper mismatch occurs, the message 
remains on the display and the machine 
remains off-line until you insert the correct 
paper.
• On : If the paper is mismatched, an error 
message displays. The machine goes off-line 
for 30 seconds then automatically clears the 
message and continues printing.
Altitude Adj. You can optimize the print quality according to 
your altitude.
Auto CR This option allows you to append the required 
carriage return to each line feed, which is useful 
to the Unix user or DOS user.
Refer to the following samples:
Job Timeout You can set the amount of time a single print job 
is active before it must print. The machine 
handles incoming data as a single job, if it comes 
in within the specified time. When an error 
occurs while processing data from the computer 
and the data flow stops, the machine waits the 
specified amount of time and then cancels 
printing if data flow does not resume. (See page 
3.4 for more information)
Maintenance This menu allows you to maintain consumables 
within the machine and check supplies life. You 
can clean fuser components. (See page 6.1 for 
more information)
Clear Setting This menu item allows you to restore the 
printers factory default settings.
MenuDescription
Emulation Type You can select the machine language. If the 
languages from the computer and the machine 
are different, the printing quality can not be 
confirmed. It is recommended to set this menu to 
Auto to switch the proper language.
MenuDescription
LF LF+CR
  AA
     BB
         CC  AA
 BB
 CC
Downloaded From ManualsPrinter.com Manuals