Samsung CLP 550 User Manual

SETUP GUIDE9
English
6Hold the handle on the imaging unit with the green roller 
facing you. Align the imaging unit with the slots in your 
printer so that the colors on both sides of the imaging unit 
slide into the corresponding colors of the slots.
CAUTION: Insert the imaging unit carefully so as not to scratch 
and damage the surface of the green roller.
7Slide the imaging unit down into the printer until it cannot 
be pushed in any further and fold the handle down. 
CAUTION: To prevent damage, do...

SETUP GUIDE12
14Firmly push the lock levers on each side towards the top 
cover, as shown below, to lock the transfer belt into place.
CAUTION: If you open the left cover for a few minutes, the 
imaging unit can be exposed to light. This causes damage to the 
imaging unit.
15After making sure that the left cover is open, close the top 
cover. Make sure that it is securely latched.
CAUTION: Do not try to close the left cover with the top cover 
open. This may cause damage to the printer....

SETUP GUIDE9
English
6Hold the handle on the imaging unit with the green roller 
facing you. Align the imaging unit with the slots in your 
printer so that the colors on both sides of the imaging unit 
slide into the corresponding colors of the slots.
CAUTION: Insert the imaging unit carefully so as not to scratch 
and damage the surface of the green roller.
7Slide the imaging unit down into the printer until it cannot 
be pushed in any further and fold the handle down. 
CAUTION: To prevent damage, do...

SETUP GUIDE14
19On the right hand side of the toner cartridge slot is a label 
that identifies which color cartridge to fit into each slot.
20Holding each toner cartridge, insert them into their 
corresponding positions shown in order of Cyan, Magenta, 
Yellow and then Black. Using both hands, grip the cartridge 
to insert into the slot. Then hold the handle to slide the 
cartridge in.
When the toner cartridges are correctly installed the yellow 
and black cartridges are not fully inserted. These will be...

SETUP GUIDE9
English
6Hold the handle on the imaging unit with the green roller 
facing you. Align the imaging unit with the slots in your 
printer so that the colors on both sides of the imaging unit 
slide into the corresponding colors of the slots.
CAUTION: Insert the imaging unit carefully so as not to scratch 
and damage the surface of the green roller.
7Slide the imaging unit down into the printer until it cannot 
be pushed in any further and fold the handle down. 
CAUTION: To prevent damage, do...

SETUP GUIDE16
Step 4. Loading Paper
The tray (Tray 1) can hold a maximum of 250 sheets of plain 
paper. You can use A4 and letter-sized paper.
To load paper:
1Pull the tray out of the printer.
2Push down on the metal plate until it locks into position.
3Flex the paper sheets back and forth to separate the pages 
and then fan them while holding one edge. Tap the edges of 
the stack on a flat surface to even it up.
%ownloadedd/romd“anuals@rinterbcomd“anuals 

SETUP GUIDE9
English
6Hold the handle on the imaging unit with the green roller 
facing you. Align the imaging unit with the slots in your 
printer so that the colors on both sides of the imaging unit 
slide into the corresponding colors of the slots.
CAUTION: Insert the imaging unit carefully so as not to scratch 
and damage the surface of the green roller.
7Slide the imaging unit down into the printer until it cannot 
be pushed in any further and fold the handle down. 
CAUTION: To prevent damage, do...

SETUP GUIDE18
6Pinch the paper guide as shown and move it towards the 
paper until it lightly touches the side of the stack. Do not 
press the guide too tightly against the edge of the paper as 
the guide may bend the paper. 
NOTE: If you want to change the paper size in the tray, refer to 
the User’s Guide of your printer supplied in the CD-ROM.
7Slide the tray back into the printer.
NOTES: 
• Do not push the width guide far enough to cause the material to 
warp. 
• If you do not adjust the width guide,...

SETUP GUIDE9
English
6Hold the handle on the imaging unit with the green roller 
facing you. Align the imaging unit with the slots in your 
printer so that the colors on both sides of the imaging unit 
slide into the corresponding colors of the slots.
CAUTION: Insert the imaging unit carefully so as not to scratch 
and damage the surface of the green roller.
7Slide the imaging unit down into the printer until it cannot 
be pushed in any further and fold the handle down. 
CAUTION: To prevent damage, do...

SETUP GUIDE20
Using a Parallel Cable
NOTES: 
• The parallel port may not be available depending on your 
country.
• To connect the printer to the parallel port of the computer 
requires a certified parallel cable. You need to buy a IEEE1284 
compliant cable that is within 3m in length.
1Make sure that both the printer and the computer are 
turned off.
2Plug the parallel printer cable into the connector on the 
back of the printer. 
Push the metal clips down to fit inside the notches on the 
cable plug....