Samsung CLP 325 User Manual

							Regulatory information_ 11
regulatory information
This machine is designed for a normal work environment and certified with several regulatory statements.
Laser Safety Statement
The printer is certified in the U.S. to c onform to the requirements of DHHS 21 CFR, chapter 1 Subchapter J for Class I(1) laser  products, and 
elsewhere is certified as a Class I laser product conforming  to the requirements of IEC 60825-1:1993 + A1:1997 + A2:2001.
Class I laser products are not considered  to be 
 hazardous. The laser system and printer are designed  so there is never any human access to 
laser radiation above a Class I level during normal operati on, user maintenance or prescribed service condition.
• Wav
elenght : 800 nm
• Beam d
 ivergence
- Paraller : 12 deg
 rees
- Perp
endicular : 30 degrees
• Ma
ximum power or energy output : 5 mW
WARNING 
Never operate or service the printer with t he protective cover removed from Laser/Sca nner assembly. The reflected beam, although invisible, 
can damage your eyes.
When using this product, these basic safety precautions should al ways 
 be followed to reduce risk of fire, electric shock, and injury to persons:
Ozone Safety
During normal operation, this machine produces ozone. The ozone  produced does not present a hazard to the operator. However, it is 
advisable that the machine be operated in a well ventilated area.
If you need additional information about ozone, contact your local Samsung dealer.
Downloaded From ManualsPrinter.com Manuals 
						

							Regulatory information_ 12
Power Saver
This printer contains advanced energy conservation technology th at reduces power consumption when it is not in active use.
When the printer does not receive data for an extended perio d of 
 time, power consumption is automatically lowered. 
ENERGY STAR and the ENERGY STAR  ma
 rk are registered U.S. marks. 
For more information on the ENERGY STAR  progra
 m see http://www.energystar.gov.
Recycling
Recycle or dispose of the packaging material for this product in an environmentally responsible manner.
China only
Correct Disposal of This Product (Waste  Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product, accessories or literature i ndicates that the product and its electronic accessories (e.g. ch arger, headset, 
USB cable) should not be disposed of with other household wastes  at the end of its working life. To prevent possible harm to th e environment 
or human health from  uncontrolled waste dis posal, separate this from ot her types of wastes and recycle it responsibly to promot e the 
sustainable reuse of material resources. 
Household users should contact either the re ta
 iler where they purchased this product, or their local government office, for details of where and 
how they can take this item for environmentally safe recycling. 
Business users should contact their supplier and check the terms and  con
 ditions of the purchase contract. This product should not be mixed 
with other commercial wastes for disposal.
Radio Frequency Emissions
FCC Information to the User
This device complies with Part 15 of  the FCC Rules. Operation is subject to the following two conditions: 
• Thi
s device may not cause harmful interference, and
•This 
device must accept  any interference received, including inte rference that may cause undesired operation.
This equipment has been tested and found to comply with the limit s fo
 r a Class B digital device, pursuant to Part 15 of the FCC Rules. These 
limits are designed to provide reasonable protection against harmf ul interference in a residential installation. This equipment generates, uses 
and can radiate radio frequency energy and, if  not installed and used in accordance with the instructions, may cause harmful interference to 
radio communications. However, there is no  guarantee that interference will not occur in a particular installation. If this equ ipment does cause 
harmful interference to radio or television reception, which can  be determined by turning the equipment off and on, the user is encouraged to 
try to correct the interference by one or more of the following measures:
Downloaded From ManualsPrinter.com Manuals 
						

							Regulatory information_ 13
•Reorient or relocate the receiving antenna.
• Incre
ase the separation between the equipment and receiver.
•Conn
ect the equipment into an outlet on a circuit diff erent from that to which the receiver is connected.
• Consul
t the dealer or experienced radio TV technician for help.
 Change or modifications not expressly approv ed by the manufacturer responsible for compliance could void the users authority to 
operate the equipment.
Canadian Radio Interference Regulations
This digital apparatus does not exceed the Class B limits for radi o noise emissions from digital apparatus as set out in the interference-causing 
equipment standard entitled “Digital Apparatus” , ICES-003 of the Industry and Science Canada.
Cet appareil numérique respecte les limites de bruits radioélectri
 ques applicables aux appareils numériques de Classe B prescrites dans la 
norme sur le matériel brouilleur: “Appareils Numériques”, ICES-003 édictée  par l’Industrie et Sciences Canada.
United states of america
Federal Communications Commission (FCC)
Intentional emitter per FCC Part 15
Low power, Radio LAN type devices (radio frequency (RF) wireless co mmunication devices), operating in the 2.4 GHz/5 GHz Band, may be 
present (embedded) in your printer system. Th is section is only applicable if these devices are present. Refer to the system la bel to verify the 
presence of wireless devices.
Wireless devices that may be in your system are only qualified for  use in the United
  States of America if an FCC ID number is o n the system 
label.
The FCC has set a general guideline of 20 cm (8 inches) separa ti
 on between the device and the body, for use of a wireless device near the 
body (this does not include extremities). This device should be  used more than 20 cm (8 inches) from the body when wireless dev ices are on. 
The power output of the wireless device (or de vices), which may be embedded in your printer, is well below the RF exposure limits as set by 
the FCC.
This transmitter must not be collocated or operatio n
  in conjunction with any other antenna or transmitter.
Operation of this device is subject to the following two condit i
 ons: (1) This device may not cause harmful interference, and (2 ) this device must 
accept any interference received, including interference  that may cause undesired operation of the device.
 
Wireless devices are not user serviceable. Do not modify them  in any way. Modification to a wireless device will void the autho rization to 
use it. Contact manufacturer for service.
FCC Statement for Wireless LAN use:
 
While installing and operating this transmitter and antenna combin ation the radio frequency exposure limit of 1m W/cm2 may be 
exceeded at distances close to the antenna installed. Therefore,  the user must maintain a minimum distance of 20cm from the ant enna at 
all times. This device cannot be colocated wi th another transmitter and transmitting antenna.
Turkey only
Russia only
Downloaded From ManualsPrinter.com Manuals 
						

							Regulatory information_ 14
Germany only
Replacing the Fitted Plug (for UK Only)
Important
The mains lead for this machine is fitted with a standard (BS 1363)  13 amp plug and has a 13 amp fuse. When you change or examine the 
fuse, you must re-fit the correct 13 amp fuse. You then need to  replace the fuse cover. If you have lost the fuse cover, do not use the plug until 
you have another  fuse cover. 
Contact the people from you purchased the machine.
The 13 amp plug is the most widely used type in the UK and should  be suitabl
 e. However, some buildings (mainly old ones) do not have normal 
13 amp plug sockets. You need to buy a suitable plug adaptor. Do not remove the moulded plug.
 
If you cut off the moulded plug,  get rid of it straight away.
You cannot rewire the plug and you may receive an  electric shock if 
 you plug it into a socket.
Important warning: 
You must earth this machine.
The wires in the mains lead have the following color code:
•G
reen and Yellow:  Earth
• Blue:  Neutral
• Brow
n:  Live
If the wires in the mains lead do not match the colors marked in your plug, do the following:
You must connect the green and yellow wire to the pin marked by the 
 letter “E” or by the safety ‘Earth symbol’ or colored green and yellow or 
green.
You must connect the blue wire to the pin whic h
  is marked with the letter “N” or colored black.
You must connect the brown wire to the pin wh ich is marked with th
 e letter “L” or colored red.
You must have a 13 amp fuse in the plug,  
 adaptor, or at the distribution board.
Declaration of Conformity (European Countries)
Approvals and Certifications
The CE marking applied to this product symbolizes Samsung Electron ics Co., Ltd. Declaration of Conformity with the following applicable 
93/68/EEC Directives of the European  Union as of the dates indicated:
CLP-320 Series:  Low Voltage Directive (2006/95/EC ), Directive (200
 4/108/EC)
CLP-325W(K):  R&TTE Directive (1999/5/EC)
The declaration of conformity may be consulted at www.samsung.com/printer , go to Support > Download center and enter your printer (MFP) 
name to browse the EuDoC. 
January 1, 1995:  Council Directive 2006/95/EC Approximation of the laws of  
 the member states related to low voltage equipment.
January 1, 1996:  Council Directive 2004/108/EC (92/31/EEC),  app
 roximation of the laws of the Member States related to electromagnetic 
compatibility.
March 9, 1999:  Council Directive 1999/5/EC on radio equipment and telecommu n
 ications terminal equipment and the mutual recognition of 
their conformity. A full declaration, defining the relevant Direc tives and referenced standards can be obtained from your Samsu ng Electronics 
Co., Ltd. representative.
Downloaded From ManualsPrinter.com Manuals 
						

							Regulatory information_ 15
European Radio Approval Information (for products fitted with EU-approved radio devices)
Low power, Radio LAN type devices (radio frequency (RF) wireless co mmunication devices), operating in the 2.4 GHz/5 GHz band, may be 
present (embedded) in your printer system wh ich is intended for home or office use. This section is only applicable if these de vices are present. 
Refer to the system label to verify  the presence of wireless devices.
Wireless devices that may be in your system are only qualified fo r use in the Europe
 an Union or associated areas if a CE mark  
with 
 a Notified Body Registration Number an d the Alert Symbol is on the system label.
The power output of the wireless device or devices that may be embed
 ded in you printer is well below the RF exposure limits as set by the 
European Commission through the R&TTE directive.
European States qualified under wireless approvals:
EU
Austria, Belgium, Cyprus, Czech Republic,  Den
 mark, Estonia, Finland, France (with frequency restrictions), Germany, Greece, Hun gary, 
Ireland, Italy, Latvia,  Lithuania, Luxembourg, Malta, The  Netherlands, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden and  the U.K.
EEA/EFTA countries
Iceland, Liechtenstein, Norway and Switzerland
European States with restrictions on use:
EU
In France, the frequency range is restricted to 2446.5-2483.5 MH z for 
 devices above 10 mW transmitting power such as wireless
EEA/EFTA countries
No limitations at this time
Regulatory Compliance Statements
Wireless Guidance
Low power, Radio LAN type devices (radio frequency (RF) wireless co mmunication devices), operating in the 2.4 GHz/5 GHz Band, may be 
present (embedded) in your printer system. Th e following section is a general overview of considerations while operating a wire less device.
Additional limitations, cautions, and concer ns for 
 specific countries are listed in the specific country sections (or country g roup sections). The 
wireless devices in your system are only qu alified for use in the countries identified by the Radio  Approval Marks on the syste m rating label. If 
the country you will be using the wireless device in, is not li sted, contact your local Radio Approval agency for requirements. Wireless devices 
are closely regulated and use may not be allowed.
The power output of the wireless device or devices that may be em b
 edded in your printer is well below the RF exposure limits as known at this 
time. Because the wireless devices (which may be embedded into  your printer) emit less energy than is allowed in radio frequency safety 
standards and recommendations, manufacturer be lieves these devices are safe for use. Regardless of the power levels, care shoul d be taken 
to minimize human contact during normal operation.
As a general guideline, a separation of 20 cm (8 inches) betw e
 en the wireless device and the body, for use of a wireless device  near the body 
(this does not include extremities) is typical. This device should  be used more than 20 cm (8 inches) from the body when wirele ss devices are 
on and transmitting.
This transmitter must not be collocated or operatio n
  in conjunction with any other antenna or transmitter.
Some circumstances require restrictions on wireless device s. 
 Examples of common restrictions are listed below:
Radio frequency wireless communication can interfere with equipment on commercial aircraft. Current aviation regulations requir e wireless 
devices to be turned off while traveling in an airplane. IEEE 802.11  (also known as wireless Ethernet) and Bluetooth communication devices 
are examples of devices that  provide wireless communication.
In environments where the risk of interference to other devices or  services is harmful or perceived as harmful, the option to use a wireless 
device may be restricted or eliminated. Airports, Hospitals,  and Oxygen or flammable gas laden atmospheres are limited examples  where use 
of wireless devices may be restricted or eliminated. When in envi ronments where you are uncertain of the sanction to use wireless devices, 
ask the applicable authority fo r authorization prior to use or turning on the wireless device.
Every country has different rest rictions on the use of wireless devices. Since your system  is equipped with a wireless device, when traveling 
between countries with your  system, check with the local Radio Approval authorit ies prior to any move or trip for any restrictions on the use of 
a wireless device in the destination country.
If your system came equipped with an internal embedded wireless de vice, do not operate the wireless device unless all covers and shields are 
in place and the system is fully assembled.
Wireless devices are not user serviceable. Do  not modify them in any way. Modification to a wireless device will void the autho rization to use it. 
Contact manufacturer for service.
Downloaded From ManualsPrinter.com Manuals 
						

							Regulatory information_ 16
OpenSSL License
Copyright (c) 1998-2001 The OpenSSL Project. All rights reserved.
Redistribution and use in source and binary forms, with or wi th
 out modification, are permitted provided that the following cond itions are met:
1. Redi
stributions of source code must retain the above copyright  notice, this list of conditions and the following disclaimer.
2. Redi
stributions in binary form must reproduce the above copyrigh t notice, this list of conditions and the following disclaimer in the 
documentation and/or other materials provided with the distribution.
3. All advertising materials mentio n
 ing features or use of this software must di splay the following acknowledgment: This product  includes 
software developed by the OpenSSL Project for use  i
 n the OpenSSL Toolkit (http://www.openssl.org/).
4. The names OpenSSL Toolkit and OpenSSL Proj ect must not be
  used to endorse or promote products derived from this software wi thout 
Prior written permission. For  written permission, please contact [email protected].
5. Pro
ducts derived from this software may not be called OpenSSL  nor may OpenSSL appear in their names without prior written 
permission of the OpenSSL Project.
6. Redistributions of any form whatsoever must retain the following  ackno
 wledgment: This product includes software developed by the 
OpenSSL Project for use in the Open SSL
  Toolkit (http://www.openssl.org/).
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT AS  IS AND A
 NY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, 
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHA NTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE 
DISCLAIMED. IN NO EVENT SHALL THE Op enSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, 
INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BU T NOT LIMITED TO, PROCUREMENT OF 
SUBSTITUTE GOODS OR SERVICES;  LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERR UPTION) HOWEVER CAUSED AND 
ON ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NE GLIGENCE OR OTHERWISE) 
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE , EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
This product includes cryptographic software written by Eric Youn g (e
 [email protected]). This product includes software written by Tim 
Hudson ([email protected]).
Original SSLeay License
Copyright (C) 1995-1998 Eric Young (eay @cryptsoft.com) All rights reserved.
This package is an SSL implementation writte n by 
 Eric Young ([email protected]). The implementation was written so as to confor m with 
Netscapes SSL.
This library is free for commercial and non-commercial use  as lo
 ng as the following conditions are adhered to. The following conditions apply to 
all code found in this distribution, be it  the RC4, RSA, lhash, DES, etc., code; not  just the SSL code. The SSL documentation i ncluded with this 
distribution is covered by the same copyright terms except that  the holder is Tim Hudson ([email protected]). Copyright remains  Eric Youngs, 
and as such any Copyright notices in the code are not to be removed. If this package is used in a product, Eric Young should be  given 
attribution as the author of the parts of  the library used. This can be in the form  of a textual message at program startup or  in documentation 
(online or textual) provided with the package.
Redistribution and use in source and binary forms, with or wi th
 out modification, are permitted provided that the following cond itions are met:
1. Redi
stributions of source code must reta in the copyright notice, this list of conditions and the following disclaimer.
2. Redi
stributions in binary form must reproduce the above copyrigh t notice, this list of conditions and the following disclaimer in the 
documentation and/or other materials provided with the distribution.
3. Al
l advertising materials mentio ning features or use of this software must di splay the following acknowledgement: This product  includes 
cryptographic software written by Eric Young ([email protected])  The word cryptographic can be left out if the routines from the library 
being used are not cryptographic related.
4. If 
you include any Windows specific code (or a derivative thereo f) from the apps directory (application code) you must include an 
acknowledgement: This product includes software  written by Tim Hudson ([email protected]).
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG AS IS A ND ANY 
 EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT 
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN 
NO EVENT SHALL THE AUTHOR OR CONTRI BUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, 
OR CONSEQUENTIAL DAMAGES (INCLUDING , BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; 
Only use drivers approved for the country in which the device will
 be
  used. See the manufacturer System Restoration Kit, or con tact 
manufacturer Technical Support for additional information.
Downloaded From ManualsPrinter.com Manuals 
						

							Regulatory information_ 17
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, 
WHETHER IN CONTRACT, STRICT LIABILITY,  OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF 
THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
The licence and distribution terms for any publicly available vers ion
  or derivative of this code cannot be changed. i.e. this code cannot simply 
be copied and put under another distribution  licence [including the GNU Public Licence.
China only
Downloaded From ManualsPrinter.com Manuals 
						

							Regulatory information_ 18
Downloaded From ManualsPrinter.com Manuals 
						

							About this user’s guide_ 19
about this user’s guide
This user’s guide provides information about basic understanding of the machine as  well as detailed explanation on each 
step during actual usage. It is a valuable  resource for both novice and professional  users for the proper installation and 
use of the machine.
 • Read the safety information before using the machine.
• If you have
  a problem using the machine,  refer to the troubleshooting chapter (See  Troubleshooting on page 75 ).
• Te
rms used in this user’s guide are explained in the glossary chapter (See  Glossary on page 96 ).
• Il
lustrations in this user’s guide may differ from  your machine depending on its options or models.
• Th
e procedures in this user’s gui de are mainly based on Windows XP.
Convention
Some terms in this guide are used interchangeably as below.
•Documen
 t is synonymous with original.
• Paper is synonymou
 s with media or print media.
• M
achine refers to printer or MFP.
The following table offers the conventions of this guide.
ConventionDescriptionExample
Bold For texts on the display or button names on the machine. Cancel
Note Provides additional information or details for the machine function and feature.
 The date format may differ from country 
to country.
Caution Contains information you can use to  protect 
 the machine from possible 
mechanical damage or malfunction. 
Do not touch the surface of the drum 
located in the toner cartridge or imaging 
unit.
Footnote Provides additional information on certain words or a phrase. a. pages per minute
(“Cross-reference”) Refers you to additional detailed information. (See Finding more information on page  20)
Downloaded From ManualsPrinter.com Manuals 
						

							About this user’s guide_ 20
Finding more information
You can find information about setting up and using your machine in the following resources, either as a print-out or on screen.
Material nameDescription
Quick Installation 
Gu
 ideThis guide provides information on setting up your mach ine. This guide is provided in the box with the printer.
User’s Guide
This guide provides you with step-by-step instructions for us ing your machine’s full features, maintaining your machine, 
troubleshooting, and replacing supplies .
Machine Driver Help
This help provides you with help information about the printer dr iver and instructions for setting up the options for printing (See  Using 
help on page  61 ).
Samsung website If you have Internet access, you can get help, support, machine dr ive
 rs, manuals and order information from the Samsung website , 
www.samsung.com/printer.
Downloadable 
software You can download useful software p

rograms from the Samsung website.
• Sync
Thru™ Web Admin Service : convenient for network administrators who nee d to manage many machines simultaneously. 
This program is for network model on ly. (h ttp://solution.samsungprinter.com)
• Samsung AnyWeb Print : helps personal users to screen-capture the websit e 
 screen in Windows Internet Explorer easily. 
(http://solution.samsungprin te
 r.com/personal/anywebprint)
• Samsung Easy Color Manager : helps Samsung color laser printer us ers to adjust 
 color as they like. 
(http://solution.samsungprinte r
 .com/personal/colormanager)
Downloaded From ManualsPrinter.com Manuals