Samsung Cht 500 Instruction Manual

							GB
11
Connecting DVD-VCR to the TV using the Coaxial Cable
Connecting DVD-VCR to the TV using the SCART Cable
To receive television programmes a signal must be received from
one of the following sources:
An outdoor aerial
An indoor aerial
A cable television network
A satellite receiver
☛Make sure that both the television and the DVD-VCR
are switched offbefore connecting the cables.
1Remove the aerial or network input cable from the television.
2Connect this cable to the 75Ωcoaxial socket marked  on 
the rear of your DVD-VCR.
3Plug the coaxial cable supplied into the  socket on your 
DVD-VCR.
4Plug the other end of the coaxial cable into the connector
previously used for the aerial on the television.
5To obtain better pictures and sound quality on your television,
you can also connect your DVD-VCR to the television via the
SCART cable (see section below) if your television is equipped
with this type of connection.
TV
You can connect your DVD-VCR to the television using the SCART cable if the appropriate input is
available on the television. You thus:
Obtain better quality sound and pictures
Simplify the setting up procedure of your DVD-VCR
☛Regardless of the type of connection chosen, you must always connect the coaxial cable
supplied. Otherwise, no picture will be visible on the screen when the DVD-VCR is switched off.
Make sure that both the television and the DVD-VCR are switched off
before connecting the cables.
1Connect the coaxial cable as indicated in the above section.
2Connect one end of the SCART cable to the AV1 (EURO AV) socket on the rear of the DVD-VCR.
3Plug the other end into the appropriate connector on the television.
RADIO ANT.
AM
FM
75COAXIAL
AUXIN OUTAUDIO
VIDEODVD & VCR
R
L
RADIO ANT.
AM
FM
75COAXIAL
AUXIN OUTAUDIO
VIDEODVD & VCR
R
L
3
2
TV
4
RADIO ANT.
AM
FM
75COAXIAL
AUXIN OUTAUDIO
VIDEODVD & VCR
R
L
Aerial
SCART Cable
RF coaxial cable
2
3
TV
 
						

							GB
12
Connecting DVD-VCR to a Satellite Receiver or Other Equipment
1. AV2 IN: By means of 21-pin Scart Cable
Plug the SCART Cable with satellite receiver or other equipment into the AV2 (DEC./EXT.) socket on the rear of
the DVD-VCR. 
After making this connection, select the source by pressing the INPUT SEL. button for the AV2 input sources. 
2. By means of RF Coaxial Cable
After making this connection, you must preset the station received through the satellite tuner. 
RF output channel of the satellite receiver should be adjusted away from channel 36, which is used by the 
DVD-VCR, e.g. re-adjust to channel 39.
1. AV1(EURO AV): By means of 21-pin Scart Cable
Plug the SCART Cable with satellite receiver or other equipment into the AV1 (EURO AV) socket on the rear of
the DVD-VCR. 
After making this connection, select the source by pressing the INPUT SEL. button for the AV1 input sources. 
2. By means of RF Coaxial Cable
After making this connection, you must preset the station received through the satellite tuner. 
RF output channel of the satellite receiver should be adjusted away from channel 36, which is used by the 
DVD-VCR, e.g. re-adjust to channel 39.
You can connect your DVD-VCR to a Satellite receiver or other DVD-VCR using the SCART cable if the
appropriate outputs are available on the equipment chosen. The following illustrations give a few
examples of the connection possibilities. 
Satellite Receiver or other EquipmentAerial
Aerial Connector
RADIO ANT.
AM
FM
75COAXIAL
AUXIN OUTAUDIO
VIDEODVD & VCR
R
L
SCART Cable
RF coaxial cable
12
TV
Satellite Receiver or other EquipmentAerial
Aerial Connector
RADIO ANT.
AM
FM
75COAXIAL
AUXIN OUTAUDIO
VIDEODVD & VCR
R
LSCART Cable
RF coaxial cable
1
2
TV
 
						

							GB
13
Plug & Auto Set up
Your DVD-VCR will automatically set itself up when it is plugged
into the mains for the first time. TV stations will be stored in
memory. The process takes a few minutes. Your DVD-VCR will
then be ready for use.
1Connect the coaxial cable as indicated on page 11. 
(Connecting Your DVD-VCR to the TV Using the Coaxial Cable)
2Plug the DVD-VCR into the mains.
Result: The Language Set menu is displayed.
3Select the required language by pressing the or❷buttons.
4Press OK to store the language selected.
Result
: A message appears.
5Press OK to start the auto scanning. The number of stations automatically stored by the VCR
depends on the number of stations that it has found.   
6The current time and date are displayed automatically. 
Check the date and time.
if it is :
Correct, Press RETURN button twice to exit the menu. 
incorrect, see page 18.
➢Auto preset can be performed by pressing 
(STOP) on 
the VCR continuously for 5 seconds or more with no 
tape inserted.
2
RADIO ANT.
AM
FM
75COAXIAL
AUXIN OUTAUDIO
VIDEODVD & VCR
R
L
TV
Auto setup
Please wait
00 %
Time            Date              YearClock Set
12 : 00         1 / JAN /    2004    THU
Auto Clock       : On
 
						

							GB
14
Tuning Your Television for the DVD-VCR
You must tune your television for the DVD-VCR only if you are
not
using a Scart cable
➢To view pictures from your DVD-VCR when a Scart
cable is used, the television must be set to the
audio/video mode (AV).
1Switch on the television.
2Switch on the DVD-VCR by pressing STANDBY/ON on the front
of the DVD-VCR or STANDBY/ON on the remote control.
3Select a programme position on the television to be reserved for
use with your DVD-VCR.
4Insert the video cassette in the DVD-VCR. Check that the 
DVD-VCR starts reading the cassette; if not, press 
❿II button. 
5Start a scan on your television or set the television to UHF
channel 36.
6Fine tune the television until the pictures and sound are obtained
clearly.
7If you cannot find the pictures and sound, or there is interference
from nearby channels, it may be necessary to change the setting
of the DVD-VCR output channel (see Setting the DVD-VCR
Output Channel on page 23 and Problems and Solutions on
page 74).  
8When the picture and sound are perfectly clear, store this
channel at the desired programme position on the television. 
Result
: That programme is now reserved for use with your 
DVD-VCR.
2
4
 
						

							GB
15
Deck Control Keys
The DVD-VCR uses one set of controls to operate bothdecks.
The following keys are helpful in successfully controlling each
deck. 
1STANDBY/ON Button
Press the STANDBY/ON button on the remote control or front
panel to turn on the DVD-VCR. 
2DVD Button
Press the DVD button on the remote control when you want to
control the DVD deck. 
The DVD indicator will light on the Front Panel Display to 
show that the DVD deck is selected. 
3VCR Button
Press the VCR button on remote control when you want to
control the VCR deck.  
The VCR indicator will light on the Front Panel Display to 
show that VHS deck is selected. 
4INPUT SEL. BUTTON
Press the INPUT SEL. button repeatedly to cycle through all of 
your input sources, including the  Tuner (PR##), AV1 (rear AV 
input), AV2 (rear AV input), AUX (rear AV input).
•It is only available when VCR deck is selected.
➢Before using the VCR operation of 19~45 pages, press
the VCR button on the remote control to select VCR
mode. 
Before using the DVD operation of 46~66 pages, press
the DVD button on the remote control to select and
watch DVD. 
STANDBY/ONPHONES
1
1
23
4
 
						

							GB
16
Inserting Batteries in the Remote Control
You must insert or replace the batteries in the remote control
when you:
Purchase the DVD-VCR
Find that the remote control is no longer working
correctly
1Push the tab in the direction of the arrow to release the battery
compartment cover on the rear of the remote control.
2Insert two AAA, RO3 or equivalent batteries, taking care to
respect the polarities:
+ on the battery with + on the remote control– on the battery with – on the remote control
3Replace the cover by aligning it with the base of the remote
control and pushing it back into place.
➢Do not mix different battery types (manganese and
alkaline for example).
1
Basic TV Tuner Operations
The following buttons are used when watching television via the
DVD-VCR’s built-in TV tuner. 
1TV/VCR Button
Press to switch between your TV’s tuner and the VCR’s internal
tuner.  
2PROG Button
Press to change to the next or previous channel. 
30-9 Buttons
Press to select channels directly.  
4INFO.
Press to display the channel you are watching. 
Also works in DVD and VCR mode. 
1
2
2
3
4
 
						

							GB
17
Copying from DVD to VCR
The DVD-VCR allows you to copy the contents of a DVD to a
VHS tape with a press of the COPY button.  
If the DVD you are attempting to copy is copy 
protected, you will not be able to copy the disc. It is not 
permitted to copy Macrovision® encoded DVDs.  
1INSERT DISC
Insert the disc you wish to copy in the DVD deck and close the
drawer.     
2Insert VHS Tape
Insert a blank VHS videotape into the VCR deck.   
3Copy the DVD to VHS Tape
Press the COPY button on the DVD-VCR front panel.  
The DVD will go into Play mode and the VCR will go into 
Record mode.     
4Stop the Copy Process 
When the DVD is finished playing, press the VCR button on the
remote control and then press the STOP button to end the copy.  
You must stop the Copy process manually when the DVD 
movie ends or the DVD may replay and record over and over 
again.  
☛The NTSC DVD or VCD Copy process can not active.
4
4
EJECTREC S.MODESTANDBY/ONPHONESCOPYPROGSELECTVOL
P.SCAN
1
EJECTREC S.MODESTANDBY/ONPHONESCOPYPROGSELECTVOL
P.SCAN
2
REC S.MODEPHONESCOPY
3
 
						

							GB
18
Setting the Menu Language
1 Open “MENU”
After pressing the MENU, press the OK or ❿.
2 Select “Language”
Use the or❷buttons to highlight 
“Language,” then press the OK or 
❿.
3 Set menu Language
Place the selection arrow next to your desired Language, then
press the OK button.
4On completion, press RETURN twice to exit the menu.
Language                    :  English
User Set                       
Auto Power Off           :  Off    
Screen Messages       :  On    
Install
Français
Deutsch
Español
Italiano
Nederlands
Language Set
English
Setting the Date and Time
Your DVD-VCR contains a 24-hour clock and calendar used to:
Automatically stop programme recording
Preset your DVD-VCR to record a programme
automatically
You must set the date and time when:
You purchase the DVD-VCR
☛Do not forget to reset the time when you change
clocks from winter to summer time and vice versa.
1After pressing the MENU, press the OK or ❿.Result: The Setup menu is displayed.
2Press the corresponding,❷buttons to select the Clock option.
3Press the OK or❿to select this option.
Result: The Clock Setmenu is displayed.
4Press ➛or❿to select the hour, minutes, day, month and year.
Result: The option selected highlight.
5Press the or❷buttons to increase or decrease the value.
Result: The day of the week is displayed automatically.
➢You can hold the or❷buttons down to scroll more 
quickly through the values.
6On completion, press RETURN three times to exit the menu.
Language                    :  English
User Set                       
Auto Power Off           :  Off    
Screen Messages       :  On    
Install
Time            Date              YearClock Set
12 : 00         1 / JAN /    2004    THU
Auto Clock       : On
 
						

							GB
19
Presetting the Stations Automatically
☛You do not need to preset the stations if you have already 
set them automatically (see Plug & Auto Set Up on page 13).
Your DVD-VCR contains a built-in tuner used to receive television
broadcasts. 
You must preset the stations received through the tuner. 
This can be done:
Plug & Auto Set up (see page 13)
Automatically
Manually (see page 20)
You can store up to 80 stations.
1After pressing the MENU, press the OK or ❿.
Result: The Setup menu is displayed.
2Press the corresponding ,❷buttons to select theInstalloption.
3Press the OK or❿to select this option.
Result: The Install menu is displayed.
4Press the corresponding or❷buttons, until the Auto Setupis selected.
And then press the OK or❿to select this option.
Result
: A message appears, indicating that any channels
already preset on your VCR will be deleted.
5Press OK to start the auto scanning.
Result:The Please Waitindication highlight on the
television screen. 
The first frequency band is scanned and the first
station found is displayed and stored.
The DVD-VCR then searches for the second
station and so on.
When the automatic scanning procedure has
finished, the DVD-VCR switches automatically to 
programme  1.
➢The number of stations automatically stored by the DVD-
VCR depends on the number of stations that it has found.
6If you wish to cancel the auto scanning before the end, press the 
MENU button to exit the menu.
➢Once the auto scanning procedure has finished,
some stations may have been stored more than once;
select the stations with the best reception and delete
the ones no longer required (see page 21).
Auto Setup
Your data will be lost
Press   OK   to continue
             Menu      to exit   
Auto SetupManual Setup
TV System                    : G
VCR Output CH            : CH 36
Install
Language                    :  English
User Set                       
Auto Power Off           :  Off    
Screen Messages       :  On    
Install
Auto Setup
                          Please Wait
                                                                   15%
VCR
 
						

							GB
20
Presetting the Stations ManuallyVCR
Language                    :  English
User Set                       
Auto Power Off           :  Off    
Screen Messages       :  On    
Install
Auto SetupManual Setup
Install
TV System                    : G
VCR Output CH            : CH 36
MANUAL TUNING
     MEMORY  :  OK
RETURN
PR                                    :                 
CH                                    :  - - -                    
MFT                                  :   -
DECODER                       :  OFF
NAME                               :  - - - -
TV  STATION  TABLE
                                                         SWAPPING :  OK
DELETE  :  CLEAR RETURN
PR           CH              NAME              DEC
 1
 2
 3
 4
 5
☛You do not need to preset the stations manually if you
have already set them automatically.
1After pressing the MENU, press the OK or ❿.Result: The Setup menu is displayed.
2Press the corresponding #,❷buttons to select theInstalloption.
3Press the OK or❿to select this option.
Result: The Installmenu is displayed.
4Press the corresponding #or ❷buttons, until the Manual
Setupoption is selected.
5Press the OK or❿to select a  Manual Setupoption.
Result: The TV STATION TABLEmenu is displayed.
6Press the #or ❷buttons to select a programme number as 
required. 
7Press the ❿!button to preset the station.
Result: The MANUAL TUNINGmenu is displayed.
8Press the ➛or❿buttons to start scanning channel.
Result: The frequency band is scanned and the first station
found is displayed.
9Press the ❷button, until the DECODERis selected.
10Press the ❿button to activate or deactivate use of the decoder 
for the TV station, if necessary.
11Press the #or❷buttons until the NAMEis selected.
The station name is set automatically from the broadcast signal.
12To change the programme’s name, press the ❿!button. 
Result
: The first letter of the name flashes. 
13To... Then...
Select a character  Press the #or❷button until the 
in the name required character is displayed 
(letters, numbers or “-” character).
Move to the next or Press the ➛or❿buttons 
previous character respectively.
14If you... Then...
Wish to store thePress the #or❷!buttons until the 
station displayedMFT is selected.Press the ➛or❿buttons to adjust the 
picture, if necessary.
Press OK to store the station
Do notwish to Press the #or ❷buttons until the CHdisplayed store the station is selected.
Press the ➛or❿buttons to go on 
scanning the frequency band and 
display the next station
Go back to the beginning of Step 9
15Repeat this procedure from Step 9onwards, until all the 
required stations have been stored.
16On completion, press the RETURN button three times to exit the 
menu.