Home > Ryobi > Saw > Ryobi Bt31001 Manual

Ryobi Bt31001 Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Ryobi Bt31001 Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 9 Ryobi manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							OPERATORS MANUAL
    10 in. (254 mm) TABLE SAW
    BT3100-1
    SAVE THIS MANUAL FOR FUTURE REFERENCE
    Your new Table Saw has been engineered and manufactured to Ryobis high standards for dependability, ease of operation,
    and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
    WARNING: To reduce the risk of injury, the user must read and understand the operators manual.
    Thank you for buying a Ryobi Table Saw. 
    						
    							Page 2 Product Specifications .............................................. 2
    Rules for Safe Operation ........................................ 3-6
    Electrical ..................................................................... 7
    Glossary of Terms For Woodworking ...................... 8
    Unpacking and Tools Needed ................................... 9
    Loose Parts List .................................................. 10-11
    Features ............................................................... 12-14
    Operating Components .............................................. 13
    Power Switch ............................................................. 13
    Turn Your Saw On ..................................................... 13
    To Turn Your Saw Off ................................................ 13
    To Lock Your Saw Switch .......................................... 13
    Blades ........................................................................ 14
    Assembly ............................................................. 15-20
    Assembly Leg Stand .................................................. 15
    Assembly Storage Brackets ....................................... 16
    Mounting Leg Stand to the Table Saw Base .............. 16
    To Install Front and Back Rails ............................. 16-17
    To Install Miter Table and Fence ................................ 17
    To Install Accessory Table and Rip Fence ................. 18
    Removing/Replacing the Throat Plate ....................... 18
    Blade and Guard Assembly ....................................... 19
    To Check Saw Blade Installation ............................... 20
    To Install Blade Guard Assembly ............................... 20
    Operation ............................................................. 21-32
    Basic Operation .......................................................... 21
    Causes of Kickback and Avoiding Kickback .............. 21
    Cutting Aids ................................................................ 21
    Types of Cuts ............................................................. 22
    Featherboard .............................................................. 23
    How To Make a Featherboard ............................... 23
    How To Mount a Featherboard ............................. 23
    Settings And Adjustments ..................................... 24-27
    To Remove The Blade .......................................... 24
    TABLE OF CONTENTS
    PRODUCT SPECIFICATIONS
    Blade Diameter 10 in. (254 mm)
    Blade Arbor 5/8 in. (16 mm)
    Cutting Depth at 0°3-9/16 in. (90.5 mm)
    Cutting Depth at 45°2-1/2 in. (63.5 mm)
    Rating 120 Volts, 60 Hz-AC Only, 15 Amperes
    Output Speed 4,800 RPM
    Net Weight Without Workstand 75 lbs. (34.1 kg.)
    Net Weight With Workstand 107 lbs. (48.6 kg.)
    To Check, Replace or Adjust The Riving Knife
    and Blade Guard Assembly ............................... 25
    To Adjust the Blade Depth .................................... 26
    To Adjust the Blade Angle ..................................... 26
    To Set the Scale to the Blade ................................ 26
    To Lock the Miter Table ......................................... 27
    Making Cuts .......................................................... 27-32
    To Make a Straight Cross Cut ............................... 27
    To Make a Miter Cut .............................................. 28
    To Make a Straight Rip Cut ................................... 28
    To Make a Bevel Cross Cut .................................. 29
    To Make a Bevel Rip Cut ...................................... 29
    To Make a Compound Miter Cut ........................... 30
    To Make a Large Panel Cut .................................. 30
    To Make Non-Through Cuts .................................. 31
    To Make Dado Cuts .............................................. 32
    Maintenance ........................................................ 33-39
    General Maintenance ................................................. 33
    Lubrication
    Locker Bracket Assembly ...................................... 33
    Tilt / Elevating Mechanism .................................... 33
    To Set Blade to 0 or 45 Degrees ................................ 34
    To Check Alignment of the Rip Fence to
    the Blade .......................................................... 34-35
    To Adjust the Bevel Locking Lever ............................. 35
    To Align the Miter Locking Clamps ............................ 35
    To Adjust the Front and Rear Rail Clamps ................ 36
    To Adjust the Accessory Table .................................. 36
    To Adjust the Sliding Miter Table Assembly ............... 36
    Checking Sliding Miter Table Assembly ................ 37-38
    Making Adjustments to Sliding Miter Fence Table
    Assembly .......................................................... 38-39
    Troubleshooting .................................................. 40-41
    Exploded View and Parts List ............................ 43-51
    Parts Ordering / Service .......................................... 52 
    						
    							Page 3
    IMPORTANT
    Servicing  requires extreme care and knowledge and should
    be performed only by a qualified service technician. For
    service we suggest you return the tool to your nearest Ryobi
    AUTHORIZED SERVICE CENTER for repair. When servic-
    ing, use only identical Ryobi replacement parts.
    WARNING:
    Do not attempt to use the tool until you have read
    thoroughly and understand completely the operator’s
    manuals. Pay close attention to the safety rules, including
    Dangers, Warnings, and Cautions. If you use this tool
    properly and only for what it is intended, you will enjoy
    years of safe, reliable service.
    Look for this symbol to point out important safety precautions.
    It means attention!!! Your safety is involved.
    WARNING:
    RULES FOR SAFE OPERATION
    The operation of any power tool can result in foreign objects being thrown into your eyes, which
    can result in severe eye damage. Before beginning tool operation, always wear safety goggles or
    safety glasses with side shields and a full face shield when needed. We recommend Wide Vision
    Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always wear eye
    protection which is marked to comply with ANSI Z87.1.
    WARNING:
    Do not attempt to use the tool until you have read thor-
    oughly and understand completely the operator’s manual.
    Pay close attention to the safety rules, including Dangers,
    Warnings, and Cautions. If you use this tool properly and
    only for what it is intended, you will enjoy years of safe,
    reliable service.
    WARNING:
    Observe all normal safety precautions related to avoiding
    electrical shock.
    The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the
    explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves
    eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention
    measures.
    Symbol Meaning
    DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or
    serious injury.
    WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or
    serious injury.
    CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or
    moderate injury. It may also be used to alert against unsafe practices that may cause property damage.
       NOTE:Advises you of information or instructions vital to the operation or maintenance of the equipment. 
    						
    							Page 4 Safe operation of this power tool requires that you read and
    understand this operators manual and all labels affixed to
    the tool. Safety is a combination of common sense, staying
    alert, and knowing how your table saw works.
    READ ALL INSTRUCTIONS
    KNOW YOUR POWER TOOL. Read the operators
    manual carefully. Learn the saws applications and
    limitations as well as the specific potential hazards related
    to this tool.
    GUARD AGAINST ELECTRICAL SHOCK BY
    PREVENTING BODY CONTACT WITH GROUNDED
    SURFACES. For example; pipes, radiators, ranges,
    refrigerator enclosures.
    KEEP GUARDS IN PLACE and in working order. Never
    operate the tool with any guard or cover removed. Make
    sure all guards are operating properly before each use.
    REMOVE ADJUSTING KEYS AND WRENCHES.  Form
    habit of checking to see that keys and adjusting wrenches
    are removed from tool before turning it on.
    KEEP WORK AREA CLEAN. Cluttered areas and
    benches invite accidents. DO NOT leave tools or pieces
    of wood on the saw while it is in operation.
    AVOID DANGEROUS ENVIRONMENT. Dont use power
    tools in damp or wet locations or expose to rain.  Keep
    work area well lit.
    KEEP CHILDREN AND VISITORS AWAY.  All visitors
    should wear safety glasses and be kept a safe distance
    from work area. Do not let visitors contact tool or extension
    cord while operating.
    MAKE WORKSHOP CHILDPROOF with padlocks or
    master switches, or by removing starter keys.
    DONT FORCE TOOL.  It will do the job better and safer
    at the feed rate for which it was designed.
    USE RIGHT TOOL. Dont force tool or attachment to do
    a job it was not designed for. Dont use it for a purpose not
    intended.
    MAKE SURE YOUR EXTENSION CORD IS IN GOOD
    CONDITION. When using an extension cord, be sure to
    use one heavy enough to carry the current your product
    will draw. An undersized cord will cause a drop in line
    voltage resulting in loss of power and overheating. A wire
    gage size (A.W.G.) of at least 14 is recommended for an
    extension cord 25 feet or less in length. If in doubt, use the
    next heavier gage. The smaller the gage number, the
    heavier the cord.
    DRESS PROPERLY. Do not wear loose clothing, gloves,
    neckties, or jewelry. They can get caught and draw you
    into moving parts. Rubber gloves and nonskid footwear
    are recommended when working outdoors. Also wear
    protective hair covering to contain long hair.
    ALWAYS WEAR SAFETY GLASSES WITH SIDE
    SHIELDS. Everyday eyeglasses have only impact-
    resistant lenses; they are NOT safety glasses.SECURE WORK. Use clamps or a vise to hold work when
    practical. Its safer than using your hand and frees both
    hands to operate tool.
    DONT OVERREACH.  Keep proper footing and balance
    at all times.
    MAINTAIN TOOLS WITH CARE.  Keep tools sharp and
    clean for better and safer performance. Follow instructions
    for lubricating and changing accessories.
    DISCONNECT TOOLS. When not in use, before servicing,
    or when changing attachments, blades, bits, cutters, etc.,
    all tools should be disconnected.
    AVOID ACCIDENTAL STARTING. Be sure switch is off
    when plugging in.
    USE RECOMMENDED ACCESSORIES. The use of
    improper accessories may cause risk of injury.
    NEVER STAND ON TOOL. Serious injury could occur if
    the tool is tipped or if the cutting tool is unintentionally
    contacted.
    CHECK DAMAGED PARTS. Before further use of the
    tool, a guard or other part that is damaged should be
    carefully checked to determine that it will operate properly
    and perform its intended function. Check for alignment of
    moving parts, binding of moving parts, breakage of parts,
    mounting and any other conditions that may affect its
    operation. A guard or other part that is damaged must be
    properly repaired or replaced by an authorized service
    center to avoid risk of personal injury.
    USE THE RIGHT DIRECTION OF FEED. Feed work into
    a blade or cutter against the direction of rotation of blade
    or cutter only.
    NEVER LEAVE TOOL RUNNING UNATTENDED. TURN
    POWER OFF. Dont leave tool until it comes to a complete
    stop.
    PROTECT YOUR LUNGS.  Wear a face or dust mask if
    the cutting operation is dusty.
    PROTECT YOUR HEARING.  Wear hearing protection
    during extended periods of operation.
    DONT ABUSE CORD.  Never yank cord to disconnect
    from receptacle. Keep cord from heat, oil, and sharp
    edges.
    USE OUTDOOR EXTENSION CORDS. When tool is
    used outdoors, use only extension cords with approved
    ground connection that are intended for use outdoors and
    so marked.
    ALWAYS KEEP THE BLADE GUARD AND RIVING
    KNIFE (SPLITTER) IN PLACE  and in working order.
    KEEP BLADES CLEAN AND SHARP. Sharp blades
    minimize stalling and kickback.
    KEEP HANDS AWAY FROM CUTTING AREA. Keep
    hands away from blades. Do not reach underneath work
    or around or over the blade while blade is rotating.  Do not
    attempt to remove cut material when blade is moving.
    RULES FOR SAFE OPERATION 
    						
    							Page 5 BLADES COAST AFTER TURN OFF.
    NEVER USE IN AN EXPLOSIVE ATMOSPHERE.  Normal
    sparking of the motor could ignite fumes.
    INSPECT TOOL CORDS PERIODICALLY. If damaged,
    have repaired by a qualified service technician at an
    authorized service facility. The conductor with insulation
    having an outer surface that is green with or without yellow
    stripes is the equipment-grounding conductor. If repair or
    replacement of the electric cord or plug is necessary, do
    not connect the equipment-grounding conductor to a live
    terminal. Repair or replace a damaged or worn cord
    immediately. Stay constantly aware of cord location and
    keep it well away from the rotating blade.
    INSPECT EXTENSION CORDS PERIODICALLY and
    replace if damaged.
    KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND
    GREASE.  Always use a clean cloth when cleaning.
    Never use brake fluids, gasoline, petroleum-based
    products, or any solvents to clean tool.
    STAY ALERT AND EXERCISE CONTROL. Watch what
    you are doing and use common sense. Do not operate tool
    when you are tired. Do not rush.
    DO NOT USE TOOL IF SWITCH DOES NOT TURN IT
    ON AND OFF. Have defective switches replaced by an
    authorized service center.
    GUARD AGAINST KICKBACK. Kickback occurs when
    the blade stalls rapidly and workpiece is driven back
    towards the operator. It can pull your hand into the blade
    resulting in serious personal injury. Stay out of blade path
    and turn switch off immediately if blade binds or stalls.
    USE RIP FENCE. Always use a fence or straight edge
    guide when ripping.
    SUPPORT LARGE PANELS. To minimize risk of blade
    pinching and kickback, always support large panels.
    BEFORE MAKING A CUT, BE SURE ALL
    ADJUSTMENTS ARE SECURE.
    USE ONLY CORRECT BLADES. Do not use blades with
    incorrect size holes. Never use blade washers or bolts that
    are defective or incorrect. The maximum blade capacity of
    your saw is 10 in. (254 mm).
    AVOID CUTTING NAILS. Inspect for and remove all nails
    from lumber before cutting.
    NEVER TOUCH BLADE or other moving parts during
    use.
    NEVER START A TOOL WHEN ANY ROTATING
    COMPONENT IS IN CONTACT WITH THE WORKPIECE.
    DO NOT OPERATE THIS TOOL WHILE UNDER THE
    INFLUENCE OF DRUGS, ALCOHOL, OR ANY
    MEDICATION.
      GROUND ALL TOOLS. If tool is equipped with three-
    prong plug, it should be plugged into a three-hole electrical
    receptacle.WHEN SERVICING use only identical Ryobi replacement
    parts. Use of any other parts may create a hazard or
    cause product damage.
    REMOVE ALL FENCES AND AUXILIARY TABLES
    before transporting saw. Failure to do so can result in an
    accident causing possible serious personal injury.
    ALWAYS  USE BLADE GUARD, RIVING KNIFE, AND
    ANTI-KICKBACK PAWLS on all through-sawing op-
    erations. Through-sawing operations are those in which
    the blade cuts completely through the workpiece as in
    ripping or crosscutting. Keep the blade guard down, the
    anti-kickback pawls down, and the riving knife in place
    over the blade.
    ALWAYS SECURE WORK firmly against rip fence or
    miter fence.
    ALWAYS USE A PUSH STICK FOR RIPPING NARROW
    STOCK. A push stick is a device used to push a workpiece
    through the blade instead of using your hands. Size and
    shape can vary but the push stick must always be nar-
    rower than the workpiece to prevent the push stick from
    contacting the saw blade. When ripping narrow stock,
    always use a push stick, so your hand does not come
    close to the saw blade. Use a featherboard and push
    blocks for non-through cuts.
    NEVER perform any operation freehand which means
    using only your hands to support or guide the workpiece.
    Always use either the rip fence or  miter fence  to position
    and guide the work.
    NEVER stand or have any part of your body in line with the
    path of the saw blade.
    NEVER reach behind, over, or within three inches of the
    blade or cutter with either hand for any reason.
    MOVE THE RIP FENCE out of the way when crosscutting.
    NEVER use rip fence as cutoff gage when crosscutting.
    NEVER attempt to free a stalled saw blade without first
    turning the saw OFF and disconnecting the saw from the
    power source.
    PROVIDE ADEQUATE SUPPORT to the rear and sides
    of the saw table for wide or long work pieces. Use a sturdy
    outrigger support if a table extension more than 24
    inches long is attached to the saw.
    AVOID KICKBACKS (work thrown back toward you) by:
    A. Keeping blade sharp.
    B. Keeping rip fence parallel to the saw blade.
    C. Keeping riving knife, anti-kickback pawls, and  blade
    guard in place and operating.
    D. Not releasing the work before it is pushed all the way
    past the saw blade using a push stick.
    E. Not ripping work that is twisted or warped or does not
    have a straight edge to guide along the fence.
    AVOID AWKWARD OPERATIONS AND HAND POSI-
    TIONS where a sudden slip could cause your hand to
    move into the cutting tool.
    RULES FOR SAFE OPERATION 
    						
    							Page 6 CHECK WITH A QUALIFIED ELECTRICIAN or service
    personnel if the grounding instructions are not completely
    understood or if in doubt as to whether the tool is properly
    grounded.
    USE ONLY CORRECT ELECTRICAL DEVICES: 3-wire
    extension cords that have 3-prong grounding plugs and 3-
    pole receptacles that accept the tools plug.
    DO NOT MODIFY the plug provided. If it will not fit the
    outlet, have the proper outlet installed by a qualified
    electrician.
    USE ONLY RECOMMENDED ACCESSORIES listed in
    this manual or addendums. Blades must be rated for at
    least 5,500 rpm. Use of accessories that are not listed may
    cause the risk of personal injury. Instructions for safe use
    of accessories are included with the accessory.
    DOUBLE CHECK ALL SETUPS. Make sure blade is tight
    and not making contact with saw or workpiece before
    connecting to power supply.
    SECURE THE SAW TO THE LEG STAND OR A WORK-
    BENCH capable of supporting the load of the saw plus any
    workpiece. This is necessary to avoid any risk of the saw
    tipping over.
    MAKE SURE THE WORK AREA HAS AMPLE LIGHT-
    ING to see the work and that no obstructions will interfere
    with safe operation BEFORE performing any work using
    the table saw.
    ALWAYS TURN OFF SAW before disconnecting it, to
    avoid accidental starting when reconnecting to power
    supply.
    RULES FOR SAFE OPERATION
    SAVE THESE INSTRUCTIONS. Refer to them frequently
    and use to instruct other users. If you loan someone this
    tool, loan them these instructions also.
    WARNING:
    Some dust created by power sanding, sawing, grinding,
    drilling, and other construction activities contains
    chemicals known to cause cancer, birth defects or
    other reproductive harm. Some examples of these
    chemicals are:
    • lead from lead-based paints,
    • crystalline silica from bricks and cement and other
    masonry products, and
    • arsenic and chromium from chemically-treated
    lumber.
    Your risk from these exposures varies, depending on
    how often you do this type of work. To reduce your
    exposure to these chemicals: work in a well ventilated
    area, and work with approved safety equipment, such
    as those dust masks that are specially designed to filter
    out microscopic particles.
    SAVE THESE INSTRUCTIONS
    SAFETY AND INTERNATIONAL SYMBOLS
    This operators manual describes safety and international symbols and pictographs that may appear on this
    product. Read the operators manual for complete safety, assembly, operating and maintenance, and repair
    information.
    MEANING
    •Do not expose to rain or use in damp locations.
    NO HANDS SYMBOL
    •Failure to keep your hands away from the blade will
    result in serious personal injury.
    SYMBOL 
    						
    							Page 7
    ELECTRICAL
    ELECTRICAL CONNECTION
    Your Ryobi Table Saw  is powered by a precision built
    electric motor. It should be connected to a power supply
    that is 120 volts, 60Hz, AC only (normal household
    current). Do not operate this tool on direct current (DC). A
    substantial voltage drop will cause a loss of power and the
    motor will overheat. If the saw does not operate when
    plugged into an outlet, double check the power supply.
    GROUNDING INSTRUCTIONS
    In the event of a malfunction or breakdown, grounding
    provides a path of least resistance for electric current to
    reduce the risk of electric shock. This tool is equipped with an
    electric cord having an equipment-grounding conductor and
    a grounding plug. The plug must be plugged into a matching
    outlet that is properly installed and grounded in accordance
    with all local codes and ordinances.
    Do not modify the plug provided. If it will not fit the outlet, have
    the proper outlet installed by a qualified electrician. Improper
    connection of the equipment-grounding conductor can result
    in a risk of electric shock. The conductor with insulation
    having an outer surface that is green with or without yellow
    stripes is the equipment-grounding conductor. If repair or
    replacement of the electric cord or plug is necessary, do not
    connect the equipment-grounding conductor to a live termi-
    nal.
    Check with a qualified electrician or service personnel if the
    grounding instructions are not completely understood, or if in
    doubt as to whether the tool is properly grounded.
    Repair or replace a damaged or worn cord immediately.
    This tool is intended for use on a circuit that has an outlet like
    the one shown in 
    Figure 1. It also has a grounding pin like the
    one shown.
    EXTENSION CORDS
    Use only 3-wire extension cords that have 3-prong ground-
    ing plugs and 3-pole receptacles that accept the tools plug.
    When using a power tool at a considerable distance from the
    power source, use an extension cord heavy enough to carry
    the current that the tool will draw. An undersized extension
    cord will cause a drop in line voltage, resulting in a loss of
    power and causing the motor to overheat. Use the chart
    provided below to determine the minimum wire size required
    in an extension cord. Only round jacketed cords listed by
    Underwriters Laboratories (UL) should be used.
    Length of Extension Cord Wire Size (A.W.G.)
    Up to 25 feet 14
    26-50 feet 12
    When working with the tool outdoors, use an extension cord
    that is designed for outside use. This is indicated by the
    letters WA on the cords jacket.
    Before using an extension cord, inspect it for loose or
    exposed wires and cut or worn insulation. Repair or replace
    a damaged or worn cord immediately.
    CAUTION:
    Keep the cord away from the cutting area and position the
    cord so that it will not be caught on lumber, tools, or other
    objects during cutting.
    COVER OF GROUNDED
    OUTLET BOX
    GROUNDING
    PIN
    MOTOR CORD
    POWER CORDSAW RECEPTACLE
    Fig. 1 
    						
    							Page 8 Anti-Kickback Pawls (Fingers)
    Device which, when properly installed and maintained, is
    designed to stop the workpiece from being kicked back
    toward the front of the saw during a ripping operation.
    Arbor
    The shaft on which a blade or cutting tool is mounted.
    Bevel Cut
    A cutting operation made with an angled blade.
    Compound Cut
    A cut with both a miter angle and a bevel angle.
    Crosscut
    A cutting or shaping operation made across the grain of the
    workpiece.
    Dado
    A non-through cut which produces a square sided notch or
    trough in the workpiece.
    Featherboard
    A device used to help control the workpiece by guiding it
    securely against the table or fence during any rip cut operation.
    Freehand
    Performing a cut without using a fence, miter gauge, fixture,
    hold down clamp, or other proper device to keep the workpiece
    from twisting during the cut.
    Gum
    A sticky, sap based residue from wood products.
    Heel
    Misalignment of the blade.
    Kerf
    The amount of material removed by the blade in a through
    cut or the slot produced by the blade in a non-through or
    partial cut.
    Kickback
    An uncontrolled grabbing and throwing of the workpiece
    back toward the front of the saw. Associated with the
    workpiece closing the kerf and pinching the blade or otherwise
    placing tension on the blade.
    Leading End
    The end of the workpiece which, during a rip type operation,
    is pushed into the cutting tool first.
    Miter Cut
    A cutting operation made with the wood at any angle other
    than 90 degrees.
    Molding
    A cut which produces a special shape in the workpiece, used
    for joining or decoration.Non-Through Cuts
    Any cutting operation where the blade does not extend
    completely through the thickness of the workpiece.
    Push Block
    A device used to feed the workpiece through the saw, except
    during narrow ripping type operations where a push stick
    should be used. It also helps keep the operators hands well
    away from the blade.
    Push Stick
    A device used to feed the workpiece through the saw to help
    keep the operators hands well away from the blade.
    Rabbet
    A notch in the edge of a workpiece.
    Resin
    A sticky, sap base substance that has hardened.
    Ripping Or Rip Cut
    A cutting or shaping operation made along the length or with
    the grain of the workpiece.
    Riving Knife
    Also known as a spreader or splitter. A metal piece, slightly
    thinner than the saw blade which helps keep the kerf open
    and prevent kickback.
    Revolutions Per Minute (RPM)
    The number of turns completed by a spinning object in one
    minute.
    Saw Blade Path
    The area over, under, behind, or in front of the blade. As it
    applies to the workpiece, that area which will be, or has been,
    cut by the blade.
    Set
    The distance that the tip of the sawblade tooth is bent (or set)
    outward from the face of the blade.
    Throw-Back
    Throwing of a workpiece in a manner similar to a kickback.
    Usually associated with a cause other than the kerf closing,
    such as a workpiece being dropped onto the blade or being
    placed inadvertently in contact with the blade.
    Through Sawing
    Any cutting operation where the blade extends completely
    through the thickness of the workpiece.
    Trailing End
    The workpiece end last cut by the blade in a ripping operation.
    Workpiece
    The item on which the cutting operation is being done. The
    surfaces of a workpiece are commonly referred to as faces,
    ends, and edges.
    GLOSSARY OF TERMS 
    						
    							Page 9
    The saw is factory set for accurate cutting. After assem-
    bling it, check for accuracy. If shipping has influenced the
    settings,  refer to specific procedures explained in the opera-
    tion and maintenance sections of this manual. Your Model BT3100-1 Table Saw is shipped complete in one
    carton and includes two table extensions, a rip fence, a miter
    fence with adjusting clamp, a blade guard, rails, and leg
    stand.
    Separate all parts from packing materials and check each
    one with the illustration and the list of Loose Parts to make
    sure all items are accounted for, before discarding any
    packing material.
    If any parts are missing, do not attempt to assemble the table
    saw, plug in the power cord, or turn the switch on until the
    missing parts are obtained and are installed correctly. Call
    1-800-525-2579 for assistance if any parts are missing or
    damaged.
    #2 PHILLIPS
    SCREWDRIVER
    ADJUSTABLE
    WRENCH
    FRAMING SQUARE SOCKET WRENCH
    WITH 7/16 in.
    SOCKET
    COMBINATION
    SQUARE
    3/4 in.
    WRENCH
    Fig. 2 3/8 in. NUT DRIVER
    FLAT BLADE
    SCREWDRIVER
    UNPACKING
    TOOLS NEEDED
    WARNING:
    If any parts are missing, do not operate this tool until the
    missing parts are replaced. Failure to do so could result
    in possible serious personal injury. 
    						
    							Page 10
    1 2
    3 45
    6
    9
    10 12
    1314
    15
    11
    8
    Fig. 3
    Key
    No. Description Quan.
    1 Rip Scale Indicator .......................................... 1
    2 Screw .............................................................. 1
    3 Hex Nut ........................................................... 1
    4 End Plug ......................................................... 4
    5 Rip Fence ........................................................ 1
    6 Sliding Miter Table .......................................... 1
    7 Accessory Table ............................................. 1
    8 Blade Guard With Riving Knife
    and Anti-Kickback Pawls ................................. 1
    9 Large Wrench ................................................. 1
    10 Small Wrench .................................................. 1
    11 Rear Rail ......................................................... 1
    12 Front Rail ........................................................ 113 Screw .............................................................. 1
    14 Washer ............................................................ 1
    15 Knob ................................................................ 1
    16 Adjusting Clamp .............................................. 1
    17 Miter Fence With Miter Indicator and Locator
        Pin Pivot ...................................................... 1
    18 3/32 in. Hex Key (Included) ............................. 1
    19 1/8 in. Hex Key (Included) ............................... 1
    20 5/32 in. Hex Key (Included) ............................. 1
    21 3/16 in. Hex Key (Included) ............................. 1
    22 Instructional Video (Not Shown)
    23 Operators Manual (Not Shown)
    24 Warranty Registration Card (Not Shown) Key
    No. Description Quan.
    7
    LOOSE PARTS LIST
    8
    15
    16 17 18 19 20 21 
    						
    All Ryobi manuals Comments (0)

    Related Manuals for Ryobi Bt31001 Manual