Runco Vx 2000d Projector User Manual
Here you can view all the pages of manual Runco Vx 2000d Projector User Manual. The Runco manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 71
Operation Runco VX-2000d Owner’s Operating Manual 59 PREL IMINARY HD/RGB Adj. Select HD/RGB Adj. from the Main Menu to view input signal resolution and timing information. To do this, select Signal Info from the HD/RGB Adj. menu. Signal Info: Select Signal Info from the HD/RGB Adj. menu to display the resolution, horizontal frequency and vertical frequency of the input current signal. OptionsSelect Options from the Main Menu to perform the following projector configuration tasks. Overscan (480i/480p...
Page 72
Operation 60 Runco VX-2000d Owner’s Operating Manual PREL IMINARY most accurate colors. If it does not, try the other choices and select the one that does. HDMI Black Level: This control compensates for incoming elevated black levels present in certain video signals. When you set it to Auto, the VX-2000d automatically determines the best setting according to the incoming video signal type. For some types of video, you may want to override the setting. Set it to 0 IRE if blacks appear elevated (dark...
Page 73
Runco VX-2000d Owner’s Operating Manual 61 PREL IMINARY 5.1 Lamp Replacement The lamp should be replaced when it reaches the end of its life (typically 2000 hours), or sooner if a noticeable degradation in brightness occurs. Contact your Runco dealer to obtain a replacement lamp. 1. Turn off the projector and unplug the power cord. Allow the projector to cool down for approximately 45 minutes prior to removing the lamp assembly for replacement. 2. Using a Phillips screwdriver, loosen the two Lamp...
Page 74
Maintenance and Troubleshooting 62 Runco VX-2000d Owner’s Operating Manual PREL IMINARY 5.2 Troubleshooting Tips Table 5-1 provides some general guidelines for troubleshooting problems you may encounter with the VX-2000d. If you encounter an issue not described here or in Section 3 (refer to Installation Considerations on page 20), or if the suggested solutions fail to resolve the problem, please contact your Runco dealer or Runco Technical Support. Table 5-1. Troubleshooting Chart SymptomPossible...
Page 75
Maintenance and Troubleshooting Runco VX-2000d Owner’s Operating Manual 63 PREL IMINARY Image geometry is incorrect. Incorrect aspect ratio selection. Select the aspect ratio that best matches the source image and screen size (refer to Table 4-1). The projected image is trapezoidal in shape. The projector is not perpendicular to the screen. Adjust the projection angle. The projector will not turn back on after it was powered down, or the image disappears during operation. The projector...
Page 76
Maintenance and Troubleshooting 64 Runco VX-2000d Owner’s Operating Manual PREL IMINARY Notes:
Page 77
Runco VX-2000d Owner’s Operating Manual 65 PREL IMINARY 6.1 RS-232 Connection and Port Configuration To interface the DHD Controller with a home theater automation/control system or a PC running terminal emulation software, connect it to your control system or PC as shown in Figure 3-11. Configure the RS-232 controller or PC serial port as follows: no parity, 8 data bits, 1 stop bit and no flow control. Set the baud rate to 19200, to match that of the DHD Controller RS-232 port. 6.2 Serial...
Page 78
Serial Communications 66 Runco VX-2000d Owner’s Operating Manual PREL IMINARY Input Selection Commands COMPONENTNAYESSelects the Component input COMPOSITENAYESSelects the Composite video input HDMI1NAYESSelects the HDMI 1 input HDMI2NAYESSelects the HDMI 2 input HD1NA YESSelects the HD 1 input HD2NA YESSelects the HD 2 input INPUT?NANAReturns active input SVIDEO1NAYESSelects the S-Video 1 input SVIDEO2NAYESSelects the S-Video 2 input Aspect Ratio Commands ANAMORPHICNAYESSelects the Anamorphic aspect...
Page 79
Serial Communications Runco VX-2000d Owner’s Operating Manual 67 PREL IMINARY Picture Adjust Commands (not available on HDMI 1 or HDMI 2 inputs) BRIGHTNESS-100/100YESSets a value for brightness BRIGHTNESS?NANAReturns brightness setting value CHROMADELAY-12/12YESSets a value for input color chroma delay CHROMADELAY?NANAReturns input color chroma delay setting COLOR-100/100YESSets a value for color COLOR?NANAReturns color setting value CONTRAST-100/100YESSets a value for contrast CONTRAST?NANAReturns...
Page 80
Serial Communications 68 Runco VX-2000d Owner’s Operating Manual PREL IMINARY Input Position Commands (not available on HDMI 1 or HDMI 2 inputs) IHEIGHT-100/100YESSets the value for input height IHEIGHT?NANAReturns input height value IHPOS-100/100YESSets a value for horizontal input position IHPOS?NANAReturns input horizontal position value IVPOS-100/100YESSets a value for vertical input position IVPOS?NANAReturns input vertical position value IWIDTH-100/100YESSets the value for input width...