Runco Rs 1100 Ultra Projector User Manual

Installation
Runco RS-1100 Series Owner’s Operating Manual 29 
PREL
IMINARY
RS-232 Controller 
Connection 
Connect a PC or home theater control/automation system (if present) to the RS-232 port 
on the RS-1100; see 
Figure 3-13. Use a standard, 4-wire RJ-11 telephone cable, wired 
straight-through.
For more information about using this connection, refer to Serial Communications on 
page 69.
Figure 3-13. RS-232 Control System Connection
S-VID /S-VID
123457896
D-Sub 9-pin female RJ-11 MaleRJ-11 to
D-Sub...

Installation
30 Runco RS-1100 Series Owner’s Operating Manual
PREL
IMINARY
Connecting 12-Volt 
Trigger Output to External 
Theater Equipment
If your RS-1100 is equipped with a CineWide with AutoScope system, use the cable 
supplied with the AutoScope Lens Motor to connect the motor to the 12-volt trigger 
output as shown in 
Figure 3-14. 
Figure 3-14. Connecting the 12-Volt Trigger Output to the AutoScope Lens Motor
If your home theater contains a retractable screen, screen mask or other 12-volt...

Installation
Runco RS-1100 Series Owner’s Operating Manual 31 
PREL
IMINARY
Connecting to AC PowerProjector: The RS-1100 ships 
with various types of AC power 
cords. Choose the one that is 
appropriate to your locale. 
Plug the female end of the power 
cord into the AC receptacle on the 
rear of the projector (AC 100V ~ 
240V). Then, connect the other end 
to your AC power source. 
AutoScope Lens Motor: With AutoScope-equipped projectors, an additional power 
cord is provided for the lens motor. Plug...

Installation
32 Runco RS-1100 Series Owner’s Operating Manual
PREL
IMINARY
3.8 
Changing the OSD 
Language
The RS-1100 OSD language is initially set to English, but can also display the menus in 
French, Spanish, Italian or German. To change the OSD language:
1. Press MENU.
2. Select Installation from the Main Menu and press ENTER.
3. Select Language from the Installation Menu and press ENTER.
4. Press  or  to highlight the desired language. (The change takes effect 
immediately.)
3.9 
Adjusting the...

Installation
Runco RS-1100 Series Owner’s Operating Manual 33 
PREL
IMINARY
3.11 
Installing and 
Adjusting the 
CineWide Anamorphic 
Lens
If you are installing a CineWide-equipped projector, proceed as follows to install and 
adjust the anamorphic lens. 
The standard RS-1100/CineWide uses a prismatic-style anamorphic lens. This type of 
lens compresses the height of the image (as opposed to stretching the width) to achieve a 
2.35:1 aspect ratio with a 1.78:1 display device. 
The RS-1100 Ultra/CineWide...

Installation
34 Runco RS-1100 Series Owner’s Operating Manual
PREL
IMINARY
Attaching Lens Mounting Assembly to Lens Motor Carriage Plate: 
1. Remove the two Yaw/X Adjustment Levers and 1/4-20 Fiber Washers from the 
bottom of the lens mounting assembly.
2. Place the Lens Mounting Assembly on top of the Lens Motor Carriage Plate. Position 
the bracket so that the long slot at the bottom of the bracket is perpendicular to the 
corresponding slots on the carriage plate.
3. Secure the Lens Mounting Assembly...

Installation
Runco RS-1100 Series Owner’s Operating Manual 35 
PREL
IMINARY
Configure Lens Motor Trigger: CineWide with AutoScope maintains constant image 
height independent of the aspect ratio, while using the full display resolution of the 
projector. It accomplishes this by moving the anamorphic lens in front of the primary lens 
when widescreen material is being viewed. When the viewer transitions back to 16:9 or 
4:3 source material, the anamorphic lens moves out of the light path.
To configure the...

Installation
36 Runco RS-1100 Series Owner’s Operating Manual
PREL
IMINARY
When the height is properly set, tighten the Height Adjustment T-Screws to secure the 
lens in place.
Adjusting the Pitch (Angle): Next, angle the lens to even out any top-to-bottom 
pincushion distortion. To do this, loosen the Pitch Adjustment T-Screws (directly below 
the Height/Y Adjustment T-Screws) on either side of the lens to allow it to pivot freely. 
Then, adjust the anamorphic lens angle so that the projected image is...

Installation
Runco RS-1100 Series Owner’s Operating Manual 37 
PREL
IMINARY
Once the proper lens angle has been set, firmly tighten the Yaw/X-Adjustment Levers to 
secure the lens in place. 
Geometry: 
1. Input an anamorphic cross-hatch test pattern to the projector.
2. Loosen the three Lens Rotation Set Screws (shown in Figure 3-17) on the lens 
adapter plate just enough to allow it to rotate freely.
3. Grasp the lens by the center ring and rotate the lens until the image is properly 
anamorphic: 
4....

Installation
38 Runco RS-1100 Series Owner’s Operating Manual
PREL
IMINARY
Focus: Finally, rotate the Focus Ring on the anamorphic 
lens to fine-tune the optical focus. 
Anamorphic Lens 
Installation and 
Adjustment - 
Standard 
RS-1100/CineWide or 
RS-1100 Ultra/CineWide
Standard RS-1100/CineWide (Prismatic Lens): The standard RS-1100 Anamorphic 
lens mount kit consists of everything shown in 
Figure 3-18. Some components shipped 
with your projector may differ slightly from what is shown in these...