Runco Rs 1100 Ultra Projector User Manual

Operation
Runco RS-1100 Series Owner’s Operating Manual 59 
PREL
IMINARY
SDTV Adjust: Use the controls in the SDTV Adj. sub-menu to improve the display of 
standard-definition signals. These controls allow you to make adjustments independently 
for each SD signal type (as opposed to the per-input controls in the 
Picture Adjustment 
menu). 
Setup: The Brightness and Contrast settings made in the Composite, S-Video, 
Component YCbCr and Deinterlacer Adjust sub-menus can be recalled by choosing 
the...

Operation
60 Runco RS-1100 Series Owner’s Operating Manual
PREL
IMINARY
Amplitude Adjust: The Amplitude Adjust menu allows you to fine-tune the 
currently-selected image aspect ratio by stretching it horizontally or vertically, in small 
increments. This can be useful if your projector is equipped with an anamorphic lens. 
The Horizontal control adjusts the image width while keeping the height constant. 
Similarly, the Vertical control adjusts the image height while keeping the width constant....

Operation
Runco RS-1100 Series Owner’s Operating Manual 61 
PREL
IMINARY
To simultaneously change the secondary IR code and synchronize that remote with a 
projector, point the remote at the projector, then press and hold 
 and  simultaneously 
for five seconds. The Remote Control edit window, shown at left, appears. Type a new, 
two-digit code. 
The procedure for changing the secondary IR code on the remote only is the same, 
except that you point the remote away from the projector. 
Reset Lamp Timer:...

Operation
62 Runco RS-1100 Series Owner’s Operating Manual
PREL
IMINARY
ISF CalibrationTo access the ISF Calibration menu, select ISF Calibration from the Main Menu and press 
ENTER. Use the number buttons on the remote control to enter the ISF Calibration menu 
passcode when prompted and press ENTER again. Then, press MENU on the remote 
control. 
Reset Picture Adjust: To restore the ISF default image settings for the current input 
source ONLY, press the 
 button to highlight “Yes.” Then, press ENTER....

Operation
Runco RS-1100 Series Owner’s Operating Manual 63 
PREL
IMINARY
Store Settings: For each input, the RS-1100 lets you store image quality settings as 
presets that you can recall at a later time. You can create up to three presets per input 
and resolution. 
To store image quality settings to a preset:
1. Select Picture Adjust from the ISF Calibration menu.
2. Select Color Temperature from the Picture Adjust menu. 
3. Use the  or  button to select the “Custom 1” or “Custom 2” color temperature....

Operation
64 Runco RS-1100 Series Owner’s Operating Manual
PREL
IMINARY
Notes: 

Runco RS-1100 Series Owner’s Operating Manual 65 
PREL
IMINARY
5.1 
Lamp Replacement
The lamp should be replaced when it reaches the end of its life (typically 2000 hours), or 
sooner if a noticeable degradation in brightness occurs. Contact your Runco dealer to 
obtain a replacement lamp.
1. Turn off the projector and unplug the power cord. 
Allow the projector to cool down for 
approximately 45 minutes prior to removing 
the lamp assembly for replacement.
2. Loosen the two captive screws from the lamp...

Maintenance and Troubleshooting
66 Runco RS-1100 Series Owner’s Operating Manual
PREL
IMINARY
5.2 
Troubleshooting Tips
Table 5-1 provides some general guidelines for troubleshooting problems you may 
encounter with the RS-1100. If the suggested solutions fail to resolve the problem or if you 
encounter an issue not described here, please contact Runco Technical Support. 
Table 5-1. Troubleshooting Chart 
SymptomPossible Cause(s)Solution
The projector does not turn 
on.  The RS-1100 is not 
plugged in...

Maintenance and Troubleshooting
Runco RS-1100 Series Owner’s Operating Manual 67 
PREL
IMINARY
TEMP and LAMP LEDs are 
both flashing red.  The lamp cover is open.
 Fans are not working 
properly.
 Close the lamp cover.
 Please contact your Runco 
dealer for assistance. 
LAMP LED lights solid red. The lamp has failed or 
exceeded its usage life. Replace the lamp with a 
new one. 
TEMP LED lights solid red. RS-1100 internal 
temperature is too high. Power off the RS-1100 
and allow it to cool down....

Maintenance and Troubleshooting
68 Runco RS-1100 Series Owner’s Operating Manual
PREL
IMINARY
Notes: