Runco Cl 810 Projector User Manual

41Runco CL-810 Owner’s Operating Manual

On-Screen Display Menus
The Image Shift menu allows you to precisely center the 
image on the screen. (These controls are available only with 
a 480i source signal.)
Horizontal: This control moves the image right or left within 
the area of available pixels. 
Vertical: This option moves the image up or down within the 
area of available pixels.
NOTES: 
1. To adjust the image position with a 480p or higher-
resolution source, use the PC & HD Adjust controls in the...

42Runco CL-810 Owner’s Operating Manual

On-Screen Display Menus
The Remote Control menu shows you the primary and 
secondary infrared (IR) codes assigned to the CL-810. The 
Primary IR code is permanently set to +20. The secondary 
IR code is also +20. 
You can change the secondary IR code if either:
•   Another device in the theater (a DVD player, for example) is responding to commands 
from the CL-810 remote control in ways that are unpredictable or undesirable. 
•  You have multiple CL-810...

43Runco CL-810 Owner’s Operating Manual

➤ Fan ControlFan Control
Mode
Fan Speed
Set Up
White Balance
Gamma Selection
SD Enhance
RVR Adjust
Image Over Scan
Image Shift
Amplitude Adjust
Video Black Level
Lamp Power
Remote Control
Reset Lamp T imer
Fan Control
Return to User OSD
Fan Control
> Auto Normal
    Auto Hi. Altitude
   Manual
Fan Speed
+2      
On-Screen Display Menus
Select  Fan Control  from the Set Up Menu to control the 
operation of the projector’s cooling fan. 
Mode: In most cases, the...

44Runco CL-810 Owner’s Operating Manual

On-Screen Display Menus
The CL-810 has been designed to incorporate setup and calibration standards 
established by the Imaging Science Foundation (ISF). The ISF has developed carefully 
crafted, industry-recognized standards for optimal video performance and has 
implemented a training program for technicians and installers to use these standards 
to obtain optimal picture quality from Runco video display devices. Accordingly, Runco 
recommends that setup and...

45Runco CL-810 Owner’s Operating Manual

➤ ICC Adjust
➤ Store Settings
➤ Splash Screen Timer 
ICC Adjust
Color    NTSC
 R   G    B    Y    C    M
Intensity  +100
Sat.     +100
Hue    M  C    0 Store Setting
Store Settings
Memory 1
ISF Night
ISF Day
Splash Screen Timer
  +20     +
CALIBRATED FOR:
CUSTOM BUILT BY:
ISF Enable
>  Off
  On
Use the ICC Adjust controls to customize the stored NTSC, 
HDTV and/or PAL color space characteristics. To do this, 
select the color space to modify. Then, select a...

46Runco CL-810 Owner’s Operating Manual

Return to User OSD ➤To exit the ISF Calibration menu, use the up- or down-arrow keys to highlight Return 
to User OSD and press Enter. 
To retur n to the ISF Calibration menu, select it from the Main Menu, press  Enter 
twice, then press MENU on the remote control. (You do not need to re-enter the 
passcode.) 

47Runco CL-810 Owner’s Operating Manual

Lamp Replacement
The lamp should be replaced when it reaches the end of its life (typically 2000 hours), 
or sooner if a noticeable degradation in brightness occurs. Contact your Runco dealer 
to obtain a replacement lamp.
1.  Turn off the projector and unplug the power cord.  Allow the projector to cool down for 
approximately 45 minutes prior to removing 
the lamp assembly for replacement.
2.  Loosen the two captive screws from the
 
lamp cover.
3.  Remove the...

48Runco CL-810 Owner’s Operating Manual

Lamp ReplacementThis page is intentionally left blank. 

49Runco CL-810 Owner’s Operating Manual

PROBLEMPOSSIBLE CAUSEREMEDY
The projector 
does not turn on There is no power from the 
power cable. Plug the power cord into the 
AC power socket on the rear of 
the projector and an electrical 
outlet.
The power switch is not turned 
on. Turn on the power switch.
The projector was turned on 
again within the cool down 
time. Wait until projector completes 
the cool down time. 
Lamp cover is not attached 
well.
Correctly attach the lamp cover.
No picture The...

50Runco CL-810 Owner’s Operating Manual

TroubleshootingThis page is intentionally left blank.