Runco Cl 810 Projector User Manual

11Runco CL-810 Owner’s Operating Manual

Overview
1.  Connector Panel
  See “Connector Panel” on page 14.
2.  AC Power IN Socket
3.  AC Power Switch
4.  Runco Logo
  Can be rotated to match floor or    
  ceiling installation.
  See “Runco Logo” on page 14.
5.  Cable Opening
  Pass cables through this opening. 6.  Cable Access Door
  Open to access connectors.
  See “Connector Panel” on page 14.
7.  Lamp Module Cover
  Remove this cover when replacing   
  the lamp. See “Lamp Replacement”  
  on page...

12Runco CL-810 Owner’s Operating Manual

OverviewThis page is intentionally left blank. 

13Runco CL-810 Owner’s Operating Manual

1.  LAMP LED
  Indicates the status of the lamp
  - Red when the lamp has exceeded
  its usage life or developed a    
  p ro b le m . P le a s e  c o n ta c t y o u r R u n c o   
  Dealer for assistance.
  - Flashing Red when the fans are
  not working or the lamp cover is    
  open. Please contact your Runco    
  Dealer for assistance.
2.  POWER LED
  Indicates the status of the power
  - Orange when the AC power cord   
  is  p lu g g e d  in to  a  w a ll...

14Runco CL-810 Owner’s Operating Manual

Connector Panel
Controls and Functions
Runco Logo
To access the connector panel, pull 
firmly on the cable access cover to 
open it.
1.  HDMI (High-Definition Multimedia Interface) Input
  Digital video signal input
2.  Component (RCA Jacks)
  480i Component (Y/CB/CR) video signal input
3.  Video (RCA Jack)
  Composite video signal input
4.  S-Video (mini DIN 4-pin) Y/C (S-video) signal input
5.  RS-232C (RJ-11 Jack)
  RS-232C control signal input (refer to page...

15Runco CL-810 Owner’s Operating Manual

Controls and Functions
Remote Control
FOCUS  LENS
ZOOM
LIGHTOFFON
VIDS-VIDCOMP1
RGBHD
INFO RVR
ENTER
EXITMENU
BRTCONTCOLTNT
HDMI
COMP2
MEM1FACTISFDAYISFNIGHT
ANA16X9VWIDELBOX4X3
CINEMAVCINE
PBPPIPPIP+
FOCUS
ACT
ZOOMPIP-
21
5
4 63
9
8 07
LENS
LIGHT
Press to turn on the remote 
control back light.
ON
Press to turn on the 
projector.
OFF
Press to turn off the 
projector.
VID (Video)
Composite video signal 
input.
S-VID (S-Video)
S-Video signal input.
COMP1...

16Runco CL-810 Owner’s Operating Manual

Controls and Functions
FOCUS  LENS
ZOOM
LIGHTOFFON
VIDS-VIDCOMP1
RGBHD
INFO RVR
ENTER
EXITMENU
BRTCONTCOLTNT
HDMI
COMP2
MEM1FACTISFDAYISFNIGHT
ANA16X9VWIDELBOX4X3
CINEMAVCINE
PBPPIPPIP+
FOCUS
ACT
ZOOMPIP-
21
5
4 63
9
8 07
LENS
CINEMA
Image in Letterbox mode is 
enlarged to a 16x9 image 
and the upper and lower 
portions are compressed.
ANA (Anamorphic)
For 16:9 DVDs.
4X3 (Standard 4:3)
The input signal will be 
scaled to fit 4:3 display mode 
in the center of the...

17Runco CL-810 Owner’s Operating Manual

Installation
Remote ControlPush the battery cover and slide it off. Install the 
two AAA batteries with the correct polarity and 
then replace the cover.
Notes on Batteries
•  Make sure that the battery polarities are correct when installing the batteries.
•  Do not mix an old battery with a new one or different types of batteries.
•  If you will not use the remote control for a long time, remove the batteries to avoid 
damage from battery leakage.
 
Notes on...

18Runco CL-810 Owner’s Operating Manual

Installation
Installation Type ➤
Installation 
Considerations
Screen Type and Size ➤
Proper  installation  of  your  projector  will  ensure  the  quality  of  your  display.  Whether  you 
are  installing  a  projector  temporarily  or  permanently,  you  should  take  the  following  into 
account to ensure your projector performs optimally.
Choose the installation type that best suits your needs: front or rear screen, floor mount 
or inverted mount.
Front...

19Runco CL-810 Owner’s Operating Manual

Installation
Rear screen installations
There are two basic types of rear screens: diffused and optical.
A diffusion screen has a surface that spreads the light striking it. Purely diffused 
screens have a gain of less than 1. The main advantage of the diffused screen is its 
wide viewing angle, similar to that of a flat screen for front screen projection. This type 
of screen is suitable when a wide viewing angle is required but there is low ambient 
room...

20Runco CL-810 Owner’s Operating Manual

Installation
Ambient Light ➤In general, minimize or eliminate light sources directed at the screen. Contrast ratio 
in your images will be noticeably reduced if light directly strikes the screen, such as 
when a shaft of light from a window or floodlight falls on the image. Images may then 
appear washed out and less vibrant.
Other considerations and tips that can help improve your installation:
•   Keep the ambient temperature constant and below 35°C (95°F)....