Roland VersaUV LEC 330 User Manual

							139Chapter 7 Specifications
7-2 Printing or Cutting Area
Maximum Area
The  printing  or  cutting  area  along  the  horizontal  plane  (the  direction  in  which  the  carriage  moves)  is  determined  by  the 
position of the pinch rollers. 
*Margin length required by the media take-up and feed systems is approximately 1,100 mm (43 in.) 
Maximum Area When Using Crop Marks
When crop marks are used, the printing or cutting area is reduced from the maximum area by an amount equal to the crop 
marks.
Printing or cutting area
12.5 mm (0.5 in )
Crop mark
Maximum area
10 mm (0.4 in.) 
10 mm (0.4 in.) 
10 mm (0.4 in.)  10 mm (0.4 in.) 
12.5 mm (0.5 in )
12.5 mm (0.5 in ) 12.5 mm (0.5 in )
Max. 736 mm (29 in.)
Media
Pinch roller (left) 10 mm 
(0.4 in.) 
Max. 24,998 mm (984 in.)
1.5  mm 
(0.1 in.) 
75 mm*
(3 in.)
If "EDGE" or "PIECE" is selected in the 
[SETUP SHEET ] menu.
Origin  point  for  printing  or 
cutting coordinates (0,0) If  "EDGE"  or  "PIECE"  is 
selected  in  the  [SETUP 
SHEET ] menu.75 mm*
(3 in.)
Pinch roller (right)
10 mm 
(0.4 in.) 
1.5  mm 
(0.1 in.) 
Printing or cutting area 210mm
(8.3in.)
Downloaded From ManualsPrinter.com Manuals 
						

							7-2 Printing/Cutting Area
140Chapter 7 Specifications
Media-cutoff Location During Continuous Printing
When a media-cutoff command is sent from the computer, the cutoff location on the media is as shown in the figure be-
low. 
75mm (3 in)
First page Margin 
(setting on the computer)
Second page
Location where 
separated
Downloaded From ManualsPrinter.com Manuals 
						

							141Chapter 7 Specifications
7-3 About the Blade 
The cutting conditions and the service life of the blade change according to the media and the operating environment, even 
when using identical blades. The service life also differs according to the type of blade. A rough guide is shown below. 
When  uncut  areas  remain  even  when  the  blade  force  is  increased  to  a  value  that  is  higher  by  50  to  60  gf  than  the  values 
shown in this chart, then replace the blade. 
*The values for "Blade life" are estimates for when cutting media of identical type. 
BladeMediaBlade force Amount of blade 
offset Blade life* 
 
(general guide)
 ZEC-U1005 General signage vinyl 50 to 150 gf0.25 mm8000 m
 ZEC-U5025 General signage vinyl
Fluorescent vinylReflective vinyl 30 to 100 gf
120 to 200 gf
100  to 200 gf 0.25 mm
0.25 mm
0.25 mm
4000 m
4000 m
4000 m
Downloaded From ManualsPrinter.com Manuals 
						

							142Chapter 7 Specifications
7-4 Locations of the Power Rating and Serial Number Labels
Power RatingUse an electrical outlet that meets the requirements for 
voltage, frequency, and amperage given here.
Serial NumberThis is required when you seek maintenance, servicing, 
or support. Never peel off the label or let it get dirty.
Downloaded From ManualsPrinter.com Manuals 
						

							143Chapter 7 Specifications
LEC-330
Printing/cutting method
Piezo ink-jet method/media-moving method
Acceptable 
media Width182 to 762 mm (7.2 to 30 in.)
ThicknessMaximum 1.0 mm (39 mil) with liner, for printing
Maximum 0.4 mm (16 mil) with liner and 0.22 mm (9 mil) without liner, for cut
-
ting
Roll outer diameterMaximum 180 mm (7.1 in.)
Roll weightMaximum 20 kg (44 lb.)
Core diameter50.8 mm (2 in.) or 76.2 mm (3 in.)
Printing/cutting width (*1)Maximum 736 mm (29 in.)
Ink cartridges TypesECO-UV  220-cc cartridge
 ColorsSix colors (cyan, magenta, yellow, black, white, and gloss) 
Ink-curing unitDual UV LED Lamp
Printing resolution (dots per inch)Maximum 1440 dpi
Acceptable toolRoland CAMM-1 series compatible
Cutting speed10 to 600 mm/s (10 to 300 mm/s in media-feed direction)
Blade force30 to 300 gf
Blade offset compensation0.000 to 1.500 mm (0 to 0.0591 in.)
Software resolution (when cutting)0.025 mm/step (0.000984 in./step)
Distance  accuracy  (when  printing) 
(*2) Error of less than ±0.3% of distance traveled, or ±0.3 mm, whichever is greater
Distance accuracy (when cutting)  Error of less than ±0.4% of distance traveled, or ±0.3 mm, whichever is greater
When distance correction has been performed (when the setting for [CUTTING 
MENU]  -  [CALIBRATION]  has  been  made):  Error  of  less  than  ±0.2%  of  distance 
traveled, or ±0.1 mm, whichever is greater
Repetition  accuracy  (when  cutting) 
(*3) ±0.1 mm or less
Alignment  accuracy  for  printing  and 
cutting (*4) ±0.5 mm or less
Alignment  accuracy  for  printing  and 
cutting when reloading media (*5) Error of less than ±0.5% of distance traveled, or ±3 mm, whichever is greater
Media take-up 
systemRoll outer diameterMaximum180 mm (7.1 in )
Roll weightMaximum 20 kg (44 lb.)
InterfaceEthernet (10BASE-T/100BASE-TX, automatic switching) 
Power-saving functionAutomatic sleep feature
Power supply
Voltage and frequencyAC 100 to 240 V ±10%, 50/60 Hz  
Required power capacity  Maximum 4.2 A 
Power  con-
sumptionDuring operationApprox. 370 W 
Sleep modeApprox. 15.3 W 
Acoustic noise 
levelDuring operation64 dB (A) or less 
During standby40 dB (A) or less 
Dimensions (with stand) (*6)2200 (W ) × 820 (D) × 1260 (H) mm (86.6 (W ) × 32.3 (D) × 49.6 (H) in.)
Weight (with stand)177 kg (390.2 lb.)
Environment
Power on Temperature: 20 to 32ºC (68 to 90ºF) (22ºC [72˚F] or more recommended) , hu-
midity: 35 to 80% (no condensation)
Power offTemperature: 5 to 40˚C (41 to 104˚F), humidity: 20 to 80% (no condensation) 
AccessoriesExclusive  stands,  power  cord,  blade,  blade  holder  (XD-CH2),  media  clamps, 
replacement blade for separating knife, cleaning kit, software RIP (Roland Ver -
saWorks ) , User's Manual, etc.
*1
The length of printing or cutting is subject to the limitations of the p\
rogram.
*2 
With Roland PET film, print travel: 1 m
Temperature: 25°C (77°F), humidity: 50%
*3
The following conditions must be met:
 Media type: Media specified by Roland DG Corp. 
 Roll media must be loaded on the shaft.
7-5 Specifications
Downloaded From ManualsPrinter.com Manuals 
						

							7-5 Specifications
144Chapter 7 Specifications
 [PREFEED] menu item must be set to "ENABLE."
 Side margins: 25 mm or more for both the left and right margins
 Front margin: 35 mm or more
 Excluding expansion/contraction of the media
Range for assured repetition accuracy
 Length 3,000 mm
*4
 Provided that media length is under 3,000 mm
 Temperature: 25°C (77°F)
 Excluding possible shift caused by expansion/contraction of the media a\
nd/or by reloading the media.
*5
 Media type : Roland PET film
 Data size: 1,000 mm in the media-feed direction, 736 mm in the carriage\
-movement direction 
 No lamination
 Automatic detection of crop marks at 4 points when media is reloaded.
 During cutting, [PREFEED] menu item must be set to "ENABLE."
 Temperature: 25°C (77°F)
 Excludes the effects of slanted movement and of expansion and contraction of the media.\
*6
During operation of the media take-up system, an operating range of appr\
oximately 80 millimeters back from the front 
edge of the dancer roller is required.
Downloaded From ManualsPrinter.com Manuals 
						

							145
Downloaded From ManualsPrinter.com Manuals 
						

							146
Downloaded From ManualsPrinter.com Manuals 
						

							Downloaded From ManualsPrinter.com Manuals 
						

							R1-090601
Downloaded From ManualsPrinter.com Manuals