Ricoh Wg4 User Manual

							39
1Getting Started
Installing an SD Memory Card
This camera uses SD Memory Cards, SDHC Memory Cards or SDXC Memory 
Cards. Captured images are saved on the SD Memory Card if a card is inserted 
in the camera. They are saved in the built-in memory if a card is not inserted 
(p.41).
• Be sure to use this camera to format (initialize) an SD Memory Card that is unused or has been previously used on other cameras or digital devices. 
Refer to “Formatting the Memory” (p.167) for instructions on formatting 
cards.
• Make sure that the camera is turned off before inserting or removing the SD  Memory Card.
• Allow the camera to dry completely before changing the SD Memory Card.  Avoid changing the card where the camera  is likely to get wet or dirty, and 
make sure that your hands are dry.
• Do not use excessive force when sliding the battery cover open and closed  because the waterproof seal may peel off. If the seal is not in the correct 
position, the camera will not be waterproof.
• The number of still pictures that ca n be stored varies depending on the 
capacity of the SD Memory Card and the selected number of recorded 
pixels and quality level (p.220).
•
The power lamp blinks while the SD Memory Card is being accessed (data 
is being recorded or read).
Backing Up DataThe camera may not be able to access data in the built-in memory in the case of a 
malfunction. Use a computer or other device to back up important data in another 
location. 
						

							40
1Getting Started
1Slide the battery cover lock as indicated by 1, and release the 
lock.
2Slide the release latch as indicated by  2, and open the battery 
cover towards  3.
3Insert an SD Memory Card into the SD Memory Card socket so 
that the label is facing toward the front of the camera (the side 
with the lens).
Push the card in all the way. Images may not be recorded correctly if the card is 
not inserted all the way.
To remove the SD Memory Card, push it in once and then pull it out.
4Close the battery cover, and slide the release latch in the 
opposite direction indicated by  2.
5Slide the battery cover lock in the opposite direction indicated 
by  1.
Make sure that the lever clicks and the cover is locked.
If the battery cover is not locked securely, water, sand, or dirt may get into the 
camera.
• The image file size varies depending on the number of recorded pixels and 
the number of images that can be saved on an SD Memory Card also varies.
•
Set the number of recorded pixels for still pictures from the [A Rec. Mode] 
menu and for movies from the [C Movie] menu.•For an approximate number of still pictures and amount of time of movies that 
can be saved on an SD Memory Card, see “Main Specifications” (p.219).
SD Memory Card
Battery cover SD Memory 
Card socket 
						

							41
1Getting Started
Turning the Camera On and Off
1Press the power button.
The camera turns on and both the power lamp and display turn on.
If the [Language/ ] screen or [Date Adjustment] screen appears when you 
turn the camera on, follow the procedure on p.43 to set the display language and/
or current date and time.
2Press the power button again.The camera turns off and both the power lamp and display turn off.
The SD Memory Card is checked when the 
camera turns on and the memory status is 
displayed.
Taking Still Pictures  1p.61
Checking the SD Memory Card
aThe SD Memory Card is inserted. Images 
will be saved on the SD Memory Card.
+The SD Memory Card is not inserted. 
Images will be saved in the built-in memory.
r
The write-protect switch on the SD Memory 
Card is in the LOCK position (p.7). Images 
cannot be recorded.
Power button/Power lamp
3 838
Memory status 
						

							42
1Getting Started
Use this function when you want to play back images straightaway without taking 
any picture.
1Press and hold down the Q button.The display turns on and the camera starts up in playback mode.
Starting-up in Playback Mode
• To switch from playback mode to capture mode, press the  Q button or 
press the shutter release button halfway.
• In order to set the camera not to start up in playback mode, set [Playback  Mode] to  P (Off) from [Startup Shortcut] in the [ W Setting] menu. (p.186)
Playing Back Still Pictures  1p.125
Q button
Power button 
						

							43
1Getting Started
Initial Settings
The [Language/ ] screen appears when the camera is turned on for the first 
time. Perform the operations in “Setting the Display Language” below to set the 
language, and in “Setting the Date and Time” (p.46) to set the current date and 
time.
1Use the four-way controller ( 2345) to choose the display 
language.
2Press the  4 button.
The [Initial Setting] screen appears in the 
selected language. If the desired settings 
for [Hometown] and [DST] (Daylight Saving 
Time) appear, proceed to step 9.
The language, date, and time can be changed later. Refer to the pages below for 
instructions.
• To change the language, follow the steps in “Changing the Display Language” 
(1 p.174).
• To change the date and time, follow the steps in “Changing the Date and Time”  (1 p.169).
Setting the Display Language
3  button
Four-way controller
4 button
MENUCancel
Initial Setting
Hometown
New York Settings complete English
DSTOFFOFFOFF
Daylight saving time 
						

							44
1Getting Started
3Press the four-way controller (3).The frame moves to [W Hometown].
4Press the four-way controller ( 5).The [W Hometown] screen appears.
5Use the four-way controller ( 45) 
to choose a city.
6Press the four-way controller ( 3).
The frame moves to [DST] (Daylight Saving Time).
7Use the four-way controller (45) to select O(On) or P (Off).
8Press the  4 button.
The [Initial Setting] screen reappears.
9Press the four-way controller ( 3) to select [Settings 
complete].
10Press the  4 button.The [Date Adjustment] screen appears. Next, set the date and time.
MENUCancel
Initial Setting
Hometown
New York Settings complete English
DSTOFFOFFOFF
MENUCancel
City
DST
New York
Hometown
OKOK 
						

							45
1Getting Started
If you accidentally select the wrong language and go to the next procedure, perform 
the following operation to set the language back.
 When the Wrong Language Has Been Inadvertently Selected
1Press the four-way controller ( 5).
2Use the four-way controller (2345) to select the desired 
language and press the  4 button.
The [Initial Setting] screen appears in the selected language.
 When the Screen After Step 2 Appears in the Wrong Language
1Press the  3 button.
This exits the setting screen and returns the camera to capture mode.
2Press the  3 button.The [A Rec. Mode] menu appears.
3Press the four-way controller ( 5) twice.
4Use the four-way controller (32) to select [Language/ ].
5Press the four-way controller ( 5).The [Language/ ] screen appears.
6Use the four-way controller (2345) to select the desired 
language.
7Press the  4 button.The [ W Setting] menu appears in the selected language.
The language is now switched to your desired language. To reset [Hometown], [Date] 
and [Time], refer to the pages below for instructions.
• To change the Hometown city, follow the steps in “Setting the World Time”  (1 p.172).
• To change the date and time, follow the steps in “Changing the Date and Time”  (1 p.169).
The video output format (NTSC/PAL) is set to the format of the city selected in 
[Hometown] on the [Initial Setting] screen. See the following pages for information on 
the available video output formats and how to change the output format.
• Video output formats available initially: “List of World Time Cities” ( 1p.218)
• To change the video output format: “Changing the Video Output Format” ( 1p.179). 
						

							46
1Getting Started
Set the current date and time and the display format.
1Press the four-way controller (5).The frame moves to [mm/dd/yy].
2Use the four-way controller (23) 
to choose the date and time 
display format.
Choose from [mm/dd/yy], [dd/mm/yy] or [yy/
mm/dd].
3Press the four-way controller ( 5).The frame moves to [24h].
4Use the four-way controller (23) to select [24h] (24-hour 
display) or [12h] (12-hour display).
5Press the four-way controller ( 5).The frame returns to [Date Format].
6Press the four-way controller (3).The frame moves to [Date].
7Press the four-way controller (5).The frame moves to the month.
8Use the four-way controller (23) to change the month.Change the day and year in the same manner.
Next, change the time.
If you selected [12h] in step 4, the camera switches between am and pm 
corresponding to the time.
9Press the four-way controller ( 3) to select [Settings 
complete].
10Press the  4 button.This confirms the date and time.
Setting the Date and Time
If you press the  4 button in step 10, the camera clock is reset to 0 seconds. 
To set the exact time, press the 4  button when the time signal (on the TV, 
radio, etc.) reaches 0 seconds.
MENU
mm/dd/yy24h
00:00
Cancel Settings complete
Date Adjustment
Date Format
Date
Time
01/01/2014 
						

							47
1Getting Started
When the [Initial Setting] or [Date Adjustment] screen is displayed, you can 
cancel the setting operation and switch to capture mode by pressing the 
3 button. In this case, the [Initial Setting] screen will appear next time 
you turn the camera on.
[Language/ ], [Date], [Time], [Hometown] and [DST] can be changed. Refer to 
the pages below for instructions.
• To change the language, follow the steps in “Changing the Display Language”  (1 p.174).
• To change the date and time, follow the steps in “Changing the Date and Time” 
(1 p.169).
• To change the Hometown city or turn the DST setting on and off, follow the steps  in “Setting the World Time” ( 1p.172). 
						

							48
2Common Operations
Understanding the Button Functions
1Q buttonSwitches to  Q mode (p.52).
2 Power buttonTurns the camera on and off (p.41).
3Shutter release buttonFocuses the camera on the subject when pressed halfway in Still Picture 
Capture Mode (except when the focus mode is set to  3, s , and \ ) (p.62).
Takes a still picture when pressed down fully (p.62).
Pressing down fully starts and stops movie recording in  C (Movie), 
 (Underwater Movie),   (High Speed Movie),  c (Time-Lapse Movie), and 
 (1cm-Macro Movie) modes (p.110, p.112, p.120, p.121, and p.122).
4 W/T buttonChanges the captured area (p.64).
5Movie button
Starts movie recording in Still Picture Capture Mode (p.114).
Displays the shutter speed adjustment screen in  b (Shutter Priority) mode.
A Mode
2 Commo n Op era tions
3
5
7 6 4
2
8
9
1