Ricoh Projector PJ X5580 User Manual

							69
Click the "Auto Search" button.
List of PJLink compatible projector in the network will be 
displayed. Select the projector you want to control, and then 
click the “Register” button.
Return to the previous screen by clicking the [OK] button.
English 
English
LAN Control
English   
						

							70
The registered projector will be displayed.
2. Registering a projector by directly entering the IP address.
Upon entering the IP address of the projector and clicking the 
"Confirm" button, the projector name will be displayed. If there 
is no problem, click the [Register] button. Projector will be 
registered.
Return to the previous screen by clicking the [OK] button. 
English
LAN Control   
						

							71
Controlling the projector with the projector 
management utility
To control the projector, switch to remote control screen by 
pressing the "Remote Control" tab. Select the projector (/ group)
that you want to control from displayed list and control with the 
button at the bottom of the screen.
[Power] button
Turn "on/off" the power of the projector and group selected 
from the projectors (/ group) list.
[Input Switch] button
Change the input of projector and group selected from the 
Projector (/ group) list. The input will not change if projector 
does not correspond to the specified input.
Correspondence between the input display of projector 
management utility of this device and the actual input signal is 
as follows.
Input name of this deviceInput name of PJLink
Computer 1RGB1
Computer 2RGB2
VideoVideo1
S-VideoVideo2
HDMI1/MHLDigital1
HDMI2Digital2
DisplayPortDigital3
English 
English
LAN Control
English   
						

							72
[Mute] button
Turn "on/off" the mute function of the projector and group 
selected from the projectors (/ group) list. This device supports 
mute of video only or audio only. Therefore, mute will change 
upon selecting video or audio.
[Information] button
Detailed information screen for the selected projector will be 
displayed. 
English
LAN Control   
						

							73
Controlling the projector with the projector 
management utility via PJ Link
1. Open the web page and select General Setup. Then configure 
PJ Link settings.
- On the PJLink Password option, click Enable to enable this 
function.
- On the Current password field, enter the current password.
- On the New password and Confirm password fields, enter the 
new password.
When done, click Apply to save the settings.
English 
English
LAN Control
English   
						

							74
2. Open the PJ Link software and click Register Projector.
3. Click Auto search. List of PJLink compatible projectors in the 
network will be displayed. 
English
LAN Control   
						

							75
4. Select the projector you want to control and click Register. 
When prompted, enter your password.
If the password verification is successful, the "unlock" icon will 
appear on the screen.
English 
English
LAN Control
English   
						

							76
Problem: No image appears on screen
  Ensure all the cables and power connections are correctly and 
securely connected as described in the “Connecting the Projector” \
section.
 Ensure the pins of terminals are not crooked or broken.
  Check if the projection lamp has been securely installed. Refer to 
the “Replacing the lamp” section for more information.
  Make sure you have removed the lens cap and the projector is 
switched on.
  Ensure that the “AV Mute” feature is not turned on.
Problem: Partial, scrolling or incorrectly displayed image
  Press “Auto Set” on the remote control.
   Adjust the computer display settings. Verify the resolution setting 
is less than or equal to 1600 x 1200 resolution. See your operating 
system’s Help file.
 If you are using a Notebook:
  1.   First, follow the steps above to adjust resolution of the 
computer.
  2. Press the toggle output settings. For example: [Fn]+[F3]
PANASONIC, NEC => Fn+F3 
HP, SHARP, TOSHIBA => Fn+F5
IBM, SONY => Fn+F7
DELL, EPSON => Fn+F8
FUJITSU => Fn+F10
APPLE =>F7
   If you experience difficulty changing resolutions or your monitor 
freezes, restart all equipment including the projector.
If you experience trouble with the projector, refer to the 
following information. If the problem persists, please contact 
your local dealer or service center. 
English
Troubleshooting   
						

							77
Problem: The screen of the Notebook computer is not 
displaying a presentation
 If you are using a Notebook PC:
   Some Notebook PCs may deactivate their own screens when a 
second display device is in use. Each has a different way to be 
reactivated. Refer to your computer’s documentation for detailed 
information.
Problem: Image is unstable or flickering
  Adjust the “Phase” or “Clock” to correct it. Refer to the  
“H. Position” or “V. Position” section for more information.\
   Check and reconfigure the display mode of your graphic card to 
make it compatible with the product. 
Problem: Image is out of focus
 Adjust the Focus Ring on the projector lens. 
   Make sure the projection screen is between the required distance. 
(refer to pages 36~37)
Problem: The image is stretched when displaying 16:9 DVD
Change the aspect ratio by pressing the “Aspect” button on the 
remote control or select “SCREEN > Aspect Ratio” from the OSD 
menu to show image with proper aspect ratio. 
Problem: Image is too small or too large
   Adjust the Zoom lever on the top of the projector.
   Move the projector closer to or further from the screen.
   Press the “Aspect” button on the remote control or press the 
“Menu” button on the projector panel, go to “SCREEN > Aspect 
Ratio” and try the different settings.
English 
English
Troubleshooting
English   
						

							78
Problem: Image is reversed
   Select “SCREEN > Projection Mode” from the OSD menu to 
adjust the image.
Problem: Lamp burns out or makes a popping sound
   When the lamp reaches its end of life, it will burn out and may 
make a loud popping sound.  If this happens, the projector will 
not turn on until the lamp module has been replaced. To replace 
the lamp, follow the procedures in the “Replacing the Lamp”. 
English
Troubleshooting