Ricoh Projector PJ X3351N User Manual

							ItemDefaultPower Timer > Timer ProjectionSpecify whether or not to enable the power timer function.
When you enable this function, the projector automatically starts projection and turns off at the specified time. If you select [On], specify
[Projection Day] and [Projection Time] to enable this function.OffPower Timer > Projection Day
Select a day of the week to start projecting using the power time function.(Not programmed)Power Timer > Projection TimeSpecify the time to start and end projecting using the power timer
function. An interval of at least ten minutes is required between the startup
time and the end time.(Not programmed)Startup Password > Register Password
Enter a 6-digit password. The current password is required to change thepassword.000000Startup Password > Password Protect
Specify whether or not to enter a password when the projector is turned
on. If this is selected, a password must be entered when the projector is turned on after the power cord has been unplugged. However, a
password is not required when turning the projector on from the standby mode.
A password is required to change this setting.OffReset All
Reset all menus to their defaults.
This function cannot restore the default settings of [User Logo] in [Default Settings 1], [Startup Password] in [Default Settings 2], the network
security settings that are reset by executing [Reset Security Settings] in [Network Application Settings], and [Administrator Password] in
[Network Application Settings].-Default Settings 2 Menu
109  
						

							USB Settings Menu
This section explains the items in USB Settings menu under the Network/USB Settings menu tab.
You can also specify and check the items in the USB Settings menu using Web Image Monitor.
However, the following items are available only on the menu screen.
• [Remove USB Mem.] in [Settings]
• [USB Memory Free Space (KB)] and [USB Memory Access Status] in [Display Status]
On Web Image Monitor, you can check [Network/USB Func. Firmware Version] on the top page.
For details about Web Image Monitor, see page 154 "Managing the Projector Using Web Image
Monitor".
Settings
Still Image
ItemDefaultDisplay Effect Select the display effect for switching the image.• None
• Push The current image is pushed off by the next image.
• Wipe The current image is wiped off by the next image.
• Fade The current image fades out and the next image fades in.NoneDisplay Interval (sec.)
Enter the slide show switching interval from 5 to 999 seconds.5 seconds
Moving Image
ItemDefaultRepeat Specify whether or not to repeat video playback.Off5. Changing the Projector Settings
110  
						

							CommonItemDefaultAuto Start SlideshowSpecify whether or not to start a slide show automatically when the
projector is connected to the USB device.OffRemove USB Mem.
The USB device can be removed when this command is executed.-
Display Status
USB Memory
ItemDefaultUSB Memory Free Space (KB)Display the space available on the USB device (Displayed in KB).-USB Memory Access Status Display whether or not the USB device can be accessed.-
Firmware Version
ItemDefaultNetwork/USB Func. Firmware VersionDisplay the firmware version of the network and USB functions.-USB Settings Menu
111  
						

							Network Settings Menu
This section explains the items in Network Settings menu under the Network/USB Settings menu tab.
You can also specify and check the items in the Network Settings menu using Web Image Monitor.
However, the following items are available only on the menu screen.
• [Simple Wireless LAN Setup], [EAP Type], [Import Client Certificate], [Client Certificate User Name], [Client Certificate List], [Import CA Certificate], [CA Certificate List], [Delete Client/CA
Certificate], [MS-CHAP v2 User Name], [MS-CHAP v2 Password], [Windows Domain Name],
[Server Certificate Authentication], [Intermediate CA Permission], [WPA/WPA2-EAP Connection
Check], and [Reset Wireless LAN Settings] in [Wireless LAN]
• [Network Setting Wizard] in [Setup Wizard]
On Web Image Monitor, you can check [Network/USB Func. Firmware Version] on the top page. For details about Web Image Monitor, see page 154 "Managing the Projector Using Web Image
Monitor".
Wired LAN
Wired LAN Settings
ItemDefaultWired LAN Specify whether to enable or disable wired LAN.EnableTransmission Speed Select a wired LAN speed that matches your network environment. Itis recommended that [Auto-Negotiation] be selected.
• Auto-Negotiation
• 10BASE-T Full Duplex
• 10BASE-T Half Duplex
• 100BASE-TX Full Duplex
• 100BASE-TX Half DuplexAuto-Negotiation5. Changing the Projector Settings
112  
						

							TCP/IP SettingsItemDefaultDHCPSpecify whether to enable or disable DHCP.
The IP address is allocated automatically from the DHCP server when
[Enable] is selected. When [Disable] is selected, enter the IP address,
subnet mask, and default gateway manually.EnableIP Address
Enter the projector's IP address.0.0.0.0Subnet MaskEnter the subnet mask.0.0.0.0Default Gateway Enter the default gateway.0.0.0.0
Wireless LAN (RICOH PJ X3351N/WX3351N/WX4241N only)
Simple Settings
ItemDefaultSimple Wireless LAN SetupAcquire the wireless LAN settings registered in the access point, and
specify infrastructure mode wireless LAN settings for the projector
automatically.
This function may not work depending on the access point.-
Wireless LAN Settings
ItemDefaultWireless LAN
Specify whether to enable or disable wireless LAN.EnableNetwork Settings Menu
113  
						

							ItemDefaultCommunication ModeSelect the wireless LAN communication mode.• Infrastructure Select this mode when you want to connect the projector to a
wireless LAN network. You need to specify [SSID] and items in
[Security] and [TCP/IP Settings] in this mode.
• Adhoc Select this mode when you want to connect the projector and
the computer directly. The projector specifies [SSID] and items in
[Security] and [TCP/IP Settings] automatically in this mode.AdhocSSID
Enter the SSID to connect to a wireless LAN network when
[Infrastructure] is selected. Enter up to 32 characters.(blank)Channel
Select the channel to use when [Adhoc] is selected.
Select the channel that matches the type of wireless LAN being used. The channels available might differ depending on the country. • 2.4 GHz: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 1111
TCP/IP Settings
ItemDefaultDHCP
Specify whether to enable or disable DHCP.
The IP address is allocated automatically from the DHCP server when
[Enable] is selected. If you select [Disable], manually enter the IP
address, subnet mask, and default gateway.EnableIP Address
Enter the projector's IP address.0.0.0.0Subnet MaskEnter the subnet mask.0.0.0.05. Changing the Projector Settings
114  
						

							ItemDefaultDefault GatewayEnter the default gateway.0.0.0.0
Security
ItemDefaultAuthentication MethodSelect the wireless LAN authentication method.• Open System
• WEP Shared Key
• WPA/WPA2-PSK
• WPA2-PSK
• WPA/WPA2-EAP
• WPA2-EAPOpen SystemEncryption Method
Select the wireless LAN encryption method.• No Encryption Communication is not encrypted. You can select [No Encryption]
if you select [Open System] in [Authentication Method].
• WEP You can select [WEP] if you select [Open System] in
[Authentication Method].
[WEP] is selected automatically when you select [WEP Shared
Key] in [Authentication Method].
• TKIP/CCMP [TKIP/CCMP] is selected automatically when you select [WPA/
WPA2-PSK] or [WPA/WPA2-EAP] in [Authentication Method].
• CCMP [CCMP] is selected automatically when you select [WPA2-PSK]
or [WPA2-EAP] in [Authentication Method].No EncryptionNetwork Settings Menu
115  
						

							ItemDefaultTransmission WEP Key NumberSelect the Key number used to authenticate and encrypt transmissions
when you select [WEP] in [Encryption Method].
• 1
• 2
• 3
• 41Network Key
Enter the WEP key when you select [Open System] or [WEP Shared
Key] in [Authentication Method] and select [WEP] in [Encryption
Method].
When using 64 bit WEP, up to 10 characters can be used for
hexadecimal and up to 5 characters for ASCII. When using 128 bit WEP, up to 26 characters can be used for hexadecimal and up to 13
characters for ASCII.
Enter PSK when [WPA/WPA2-PSK] or [WPA2-PSK] is selected in [Authentication Method].
When using a PSK, up to 64 characters can be used for hexadecimal
and 8 to 63 characters for ASCII.(blank)EAP Type
Specify the WPA/WPA2-EAP type when [WPA/WPA2-EAP] or
[WPA2-EAP] is selected in [Authentication Method]. You can select EAP-TLS or EAP-PEAP.
• EAP-TLS A client certificate and a CA certificate must be imported to the
projector.
• EAP-PEAP A CA certificate must be imported to the projector.EAP-TLSImport Client Certificate
Imports the client certificate used for WPA/WPA2-EAP or WPA2-EAPwhen [EAP-TLS] is selected in [EAP Type].-5. Changing the Projector Settings
116  
						

							ItemDefaultClient Certificate User NameEnter the client certificate user name used for WPA/WPA2-EAP orWPA2-EAP when [EAP-TLS] is selected in [EAP Type].
This setting is optional. If it is blank, the default value of the certificate
will be used to decrypt the certificate.(blank)Client Certificate List
Displays a list of imported client certificates.-Import CA CertificateImports a CA certificate when [WPA/WPA2-EAP] or [WPA2-EAP] is
selected in [Authentication Method].-CA Certificate List
Displays a list of imported CA certificates.-Delete Client/CA Certificate Deletes all imported client and CA certificates.-MS-CHAP v2 User NameEnter the MS-CHAP v2 user name when [EAP-PEAP] is selected in
[EAP Type]. You can enter up to 31 characters including spaces.(blank)MS-CHAP v2 Password
Enter the MS-CHAP v2 password when [EAP-PEAP] is selected in
[EAP Type]. You can enter up to 128 characters including spaces.(blank)Windows Domain Name
Enter the Windows domain name when [EAP-PEAP] is selected in
[EAP Type]. You can enter up to 64 characters including spaces. “@”
and backslashes cannot be used.(blank)Server Certificate Authentication
Specify whether to enable or disable server certificate authentication.EnableIntermediate CA PermissionSpecify whether to enable or disable intermediate CA permission.EnableWPA/WPA2-EAP Connection Check Checks the WPA/WPA2-EAP connection.-Network Settings Menu
117  
						

							Reset Wireless LAN SettingsItemDefaultReset Wireless LAN SettingsThe following wireless LAN settings are reset to their defaults:
Communication Mode, SSID, Channel, Authentication Method,
Encryption Method, Transmission WEP Key Number, Network Key,
DHCP, IP Address, Subnet Mask, Default Gateway.-
LAN Common
Specify the wired LAN and wireless LAN settings.
Preferred Default Gateway (RICOH PJ X3351N/WX3351N/WX4241N)
ItemDefaultPreferred Default Gateway
Select the network interface for the projector that is connected to bothwired and wireless LAN.
• Wired LAN
• Wireless LANWired LAN
DNS Settings
ItemDefaultHost Name
Display the projector's host name.
The [Projector Name] in [Projector ID] is used as the projector’s host
name.-Domain Name
Enter the projector's domain name. Enter up to 63 characters.(blank)5. Changing the Projector Settings
118