Ricoh Projector PJ X3351N User Manual

2. Computer2 In/Monitor Out portFor inputting RGB signals, or outputting the image signals input into the "Computer1 In port" to an externaldisplay device. You can switch the purpose of this port in [Computer 2 Terminal] under [Default Settings 1].
3. Video In port For inputting image signals from a video player.
4. HDMI port For inputting HDMI signals from a computer or video player.
5. Audio In port For inputting audio signals from a computer or video player.
6. Audio Out port For outputting...

4. [Input] buttonSwitches the signal input. For details about how to switch the input signal, see page 38 "Projecting an
Image".
5. [Power] button Turns the projector on and off. You can confirm the status of the projector with the indicator.• On: Power is on.
• Off: Power is off.
• Flashing at 1 or 3 second intervals: Standby.
• Flashing at short intervals: Starting up or cooling.
6. [Focus] button/[Eco] button • [Focus] button (RICOH PJ X3351N/WX3351N)Adjusts the focus manually. Press it, and...

Remote Control Parts and Their Functions
1. [Menu] buttonDisplays the menu screen. Press it again to close the menu screen.
2. [Input] button Switches the signal input. For details about how to switch the input signal, see page 38 "Projecting anImage".
3. [AV Mute] button Temporarily blanks the screen and mutes the audio. For details, see page 48 "Temporarily Blanking the
Image and Muting the Audio".
4. Arrow buttons Used to operate the menu screen and the value bar.
5. Number buttons...

9. [Enter] buttonEnters the selected item or mode.
10. [Zoom] button Displays the digital zoom bar. Press it, and then adjust the size of the projected image using the [
] and []
buttons. For details, see page 43 "Reducing the size of the projected image".
11. [Focus] button • RICOH PJ X3351N/WX3351NAdjusts the focus manually. Press it, and then adjust the focus using the [
] and [] buttons. For details,
see page 44 "Adjusting the focus of RICOH PJ X3351N/WX3351N".
• RICOH PJ...

How to Use the Remote ControlYou can use the remote control to turn the projector on and off, and to change the signal of the imagebeing input and projected. You can also enlarge or reduce the image and mute the audio.
Note the following precautions when using the remote control: • Do not drop or hit the remote control.
• Do not place the remote control in a place that is very hot or very humid.
• Do not get the remote control wet. Also, do not place it on anything that is wet. • Do not dismantle the...

Loading Batteries into the Remote Control• For safe operation, follow the warnings below regarding the batteries. If you use the batteriesincorrectly, it may result in fire or injury due to batteries leaking or exploding.
• Do not use batteries other than the ones specified.
• Do not mix and use batteries that are different types or that are new and old.
• Correctly insert batteries according to the polarity (
/).
• Do not charge non-rechargeable batteries.
• Do not heat or throw the batteries into fire...

Removing batteries
1.Remove the battery cover from the remote control.
2. Remove the batteries.
3. Close the battery cover.
Inputting Text
Use the keyboard that is displayed on screen to input text on the setting screen. 1. Select a character using the [
], [], [], and [] buttons on the remote control.
The selected character is highlighted in orange.
2. Press the [Enter] button.
The selected character appears in the text area.
3. After inputting all the characters, select [OK].
4. Press the [Enter]...

Assigning an ID number to the projector
To operate multiple projectors with a single remote control, assign a different ID number to each
projector. Use the buttons on the control panel to perform the following procedure.
1. Press the [Menu] button.
2. Select [Default Settings 2], and then press the [
] button.
3. Select [Remote Control ID], and then press the [Enter] button.
4. Select the ID number to assign to the projector, and then press the [Enter] button.
5.Select [OK] on the confirmation screen,...

1.Press and hold the [ID] button, and then press the number button that is the ID number of
the projector you want to operate for at least three seconds.
After the ID number of the remote control is switched, you can operate the projector with the
remote control.
How to Use the Remote Control
27CZE109   

Positioning the Projector
When positioning the projector, place it so that the projector's lens faces the screen. Make sure the
projector and the screen are parallel to each other.
Adjust the distance between the projector and the screen according to the size of the projected image.
For details, see page 29 "Relationship Between the Projection Distance and the Screen Size".
• The projector can be installed at any vertical angle. However, the projector cannot be tilted to the left or right. Do...