Ricoh Projector PJ WXL6280 User Manual

51
Level 1Level 2Level 3Level 4Level 5Default
OPTION
Power Settings
Standby Power Mode0.5W mode0.5W modeCommunication mode
Direct Power OnOffOffOn
Auto Power Off
No
20 Mins
5 Mins10 Mins15 Mins20 Mins25 Mins30 Mins
Sleep Timer
No
No2 Hours4 Hours6 Hours
Light Source Settings
Light Source Mode
Constant Power
Constant PowerConstant LuminanceEco Mode Constant Power Settings0 - 10 10Constant Luminance Settings0 - 10 7
Total Projector Hours
Light SensorLight Sensor CalibrationCalibrated?(Display  Yes/No)...

52
Level 1Level 2Level 3Level 4Level 5Default
OPTIONInformation
Standby Power ModeIP AddressDHCPSystem TemperatureFactory ResetYes/No (Dialog box)Service 

53
Picture Menu
PICTURE
Display Mode
Brightness
Contrast
Sharpnes s
Color
Tint
Phase
Frequency
Horz Position
Vert Position
PICTUR
E
OUTPUT SETU P
OPTION Presentatio
n
50
50 2
50
50
50
50
50
50
PICTURE (1/2)
PICTURE
Auto Image
Color Matching
Advanced
PICTUR
E
OUTPUT SETU P
OPTION
PICTURE (2/2)
Display Mode
Optimize the projector for displaying images under certain conditions, such as Pre-
sentation, Video, Bright, DICOM SIM, Blending, 2D high speed, 3D, and user-defin-
able preset. It will affect Gamma,...

54
Contrast
Adjust the degree of difference between the lightest and darkest parts of the picture 
and change the amount of black and white in the image.
Sharpness
Select the edge clarity of the image.
Color
Adjust a video image from black and white to fully saturated color. The color setting 
applies to video sources only.
Tint
Adjust the red-green color balance in the image of video images. The tint setting 
applies to video sources only.
Phase
Analog signals only. Adjust pixel phase when the image...

55
3D Display
Select the 3D relating settings.
•  3D Enable:
 -Off: Disable 3D function.
 -On: Enable 3D function, Supports frame sequential 3D at 120Hz.
• 3D Invert: When 3D synchronous error, user can toggle the item to correct 3D 
synchronous.
NOTE:
 ™3D supported format timings:1280x720@120Hz, 1024x768@120Hz frame sequent\
ial. 
 ™When input timing is 120 Hz frame sequential, the keystone and color tem\
perature function will be disable temporary.
Color Matching
You may require a unique...

56
• Manual Adjustment
1. Adjust  color  slide  bars  and  judge  image  color  by  eye  or  meter. A  user-
defined color “adjustment” can be applied.
2. Use this submenu if you do not have specific color coordinates in mind and 
will judge color performance by eye or meter. As for Meter Adjustment, each 
color control actually defines new x/y coordinates for that color and changes 
its  hue. The  main  colors  (red  part  of  red,  green  part  of  green  and  blue  part 
of  blue)  adjust  the...

57
Film Mode
• Control film mode detection and determine whether the original source of the input video was film or video.
 -Off: Films are not detected.
 -On: Films are detected automatically.
NOTE:
 ™This function is available for interlaced video signals.
Extreme Black:
• Contrast can be increased by a dark content.
 -Off: Disable Extreme Black.
 -On: The projector will automatically improvement contrast. 

58
Output Menu
OUTPUT
Aspect Ratio
Overscan
H Digital Zoom
V Digital Zoom
H Digital Shif t
V Digital Shif t
Image Warping
PIP/PBP
PICTURE
OUTPUT SETU P
OPTION Auto
Off
100
100 50
50
Aspect Ratio
Display an image with the detected size, or resize the image by maximizing either 
the height, width or both, or resize to the maximum size possible while keeping the 
original aspect ratio.
• Auto: Display with the detected size.
• 4:3: Retain 4:3 aspect ratio.
• 16:10: Retain 16:10 aspect ratio.
• Native:...

59
V Digital Shift
Move the display area vertically if its size has been changed by the Digital Zoom 
setting.
Image Warping
• H Keystone: Adjust the keystone horizontally and make a squarer image.  
Horizontal keystone is used to correct a keystoned image shape in which the 
left and right borders of the image are unequal in length. This is intended for 
use with horizontally on-axis applications.
B
A
B
A 
Ind.WXGA WUXGA
A12.3% 7.1%
B 7.7% 5.2%
• V Keystone: Adjust the keystone vertically and make a...

60
PIP/PBP
• PIP/PBP Enable: Toggle between displaying two sources at once (Main and 
PIP/PBP images) or one source only.
• Main Source: From the list of active inputs, select one to be used as the main 
image.
• Sub Source: From the list of active inputs, select one to be used as the PIP/
PBP.
• Swap: Change the main image to PIP/PBP, and the PIP/PBP to main image. 
Swapping is available only when PIP/PBP is enabled.
• Size: Select the PIP/PBP size. Available options: Small, Medium, or Large.
• Layout:...