Ricoh Projector PJ WXL6280 User Manual

31
 
Remote Control
ONOFF
213
546
879
GammaBrightCont.PIP
0InfoMode
AutoInput
MenuExit
Hot KeyAV MutePattern
FocusLens H
Lens V
Keystone H Keystone V
Zoom
Enter
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24 

32
Ind.Part NameDescription
1Power onTurn projector ON.
2Number KeysEnter  a  number,  such  as  a  value  for  an  IP  address, etc.
3InfoDisplay source image information.
4AutoAutomatically optimize image.
5Enter• Select a highlighted menu item.• Change or accept a value.
6Arrow Keys• Adjust a setting UP or DOWN.• Navigate within a menu.
7MenuDisplay menus.
8BrightAdjust amount of light in the image.
9GammaAdjust mid-range levels.
10Lens HAdjust the position of the image horizontally.
11Lens VAdjust...

33
132Remove the battery compartment cover as shown in the illustration. 
Replace the cover. Do not mix different types of batter-ies or new and old batteries.
Install new batteries (AAA/R03). Ensure that you have the batteries’ polarity (+/–) aligned correctly.
Remote Control Battery Installation
To ensure safe operation, please observe the following precautions :
■  Use AAA/R03 type battery.
■  Avoid contact with water or liquid.
■  Do not expose the remote control to moisture or heat.
■  Do not drop...

34
Remote Control Operating Range
Point the remote control toward the projector (Remote Receiver) when 
pressing any button.
ONOFF213546879
GammaBrightCont.PIP
0InfoModeAutoInput
MenuExit
Hot KeyAV MutePatternFocusLens HLens V
Keystone H Keystone VZoom
Enter
ONOFF213546879GammaBrightCont.PIP
0InfoModeAutoInputMenuExitHot KeyAV MutePatternFocusLens H
Lens V
Keystone H Keystone VZoom
Enter
Maximum operating range for the remote control is about 33’ (10m) a\
nd 
±30° (horizontally) in front of the...

35
Installation
Adjust the Projector Position
When you select a position for the projector, consider the size and shape of your 
screen, the location of your power outlets, and the distance between the projector 
and the rest of your equipment. Follow these general guidelines:
• Position the projector on a flat surface at a right angle to the screen. The pro-
jector (with the standard lens) must be at least 3 feet (0.9m) from the projection 
screen.
• Position the projector to the desired distance from...

36
Removing and Installing the Lens
When handling the projector after lens installation, make sure the front lens cap is 
placed on the lens to protect the lens surface from potential damage. When carrying 
or moving the projector, do not handle by the lens. This may damage the lens, the 
chassis or other mechanical parts within the projector.
Installation Steps:
1. Center the lens: Ensure that the lens is at or near its center position. Attempt-
ing to remove the lens when at a large offset may cause...

37
Adjusting the Projector’s Height
The projector is equipped with elevator rubber feet for adjusting the im\
age 
height.
1. Locate the adjustable foot you wish to modify on the underside of the projector.
2. Rotate the adjustable ring clockwise to raise the projector or counter clockwise 
to lower it. Repeat with the remaining feet as needed.
Adjusting the Projected Image
12 

38
Connect to Computer
1234567
8
Ind.Connector NameInd.Connector Name
1RS232 Cable5VGA out Cable
2HDMI Cable6USB Type A Cable
3VGA in Cable7DVI Cable
4Mini USB Cable8Power Cord
NOTE:
 ™The diagram shows the cables/connectors that may be used to connect to v\
arious devices.
 ™Due to the difference in applications for each country, the accessories required in some regions may be different from those 
shown.
 ™This diagram is for illustrative purposes only, and does NOT indicate that these...

39
Connect to Video Equipment
12
3
4
5
6
Ind.Connector NameInd.Connector Name
1Component (YPbPr) Cable4VGA in Cable
2HDMI Cable53 RCA Component Cable
3VGA to RBG SCART615-pin to 3 RCA Component/HDTV Adapter
NOTE:
 ™The diagram shows the cables/connectors that may be used to connect to v\
arious devices.
 ™Due to the difference in applications for each country, the accessories required in some regions may be different from those 
shown.
 ™This diagram is for illustrative purposes only, and...

40
Turn the Projector On
1. Ensure that the power cord and signal cable are securely connected. The 
Power button on the built in keypad is illuminated.
2. Turn on the projector by pressing “” on the remote control or press “” on 
the built-in keypad. The Status LED is Orange with a long blink. 2
3. Turn on the source. Press the Input key on the remote control to select an input 
source (VGA, HDMI, or Component). 3
4. The projector detects the source you selected and displays the image.
NOTE:
 ™The...