Ricoh Projector PJ WX4152NI User Manual

							• For details about the USB devices and files supported by the projector, see page 47 "Requirements
for Projecting Images from a USB Device".
• Do not disconnect the power cord when using the power timer function. The projector cannot start if
the power cord is disconnected.
Customizing a Slide Show You can customize the display effect and display interval for a slide show. These functions are useful for
decorating shop windows more effectively.
Changing the display effect for a slide show You can change the display effect for switching images. The available display effects are the following:
Push
The current image is pushed off by the next image. Wipe
The current image is wiped off by the next image. Fade
The current image fades out and the next image fades in. 1.
Press the [Menu] button. Projecting Images in a Slide Show
59 
CZE163 
CZE164 
CZE165   
						

							1.
Select [Network/USB Settings], and then press the [ ] button.
2.
Select [USB Settings], and then press the [Enter] button.
3. Select [Settings], and then press the [ ] button.
4. Select [Display Effect], and then press the [Enter] button.
5. Select a display effect, and then press the [Enter] button. 6.
Press the [Menu] button.
7. Select [Reflect], and then press the [Enter] button.
8. Press the [Menu] button to close the menu screen.
Adjusting the slide show switching interval You can adjust the slide show switching interval from 5 to 999 seconds.
4. Useful Functions
60 
CZE158  
CZE161   
						

							1.
Press the [Menu] button.
2. Select [Network/USB Settings], and then press the [ ] button.
3.
Select [USB Settings], and then press the [Enter] button.
4. Select [Settings], and then press the [ ] button.
5. Select [Display Interval (sec.)], and then press the [Enter] button.
6. Specify a slide show switching interval.
7. Press the [Menu] button.
8. Select [Reflect], and then press the [Enter] button.
9. Press the [Menu] button to close the menu screen. Projecting Images in a Slide Show
61 
CZE158    
						

							Specifying the Sound Quality
You can select a sound quality setting for the built-in speaker that is applicable for the type of audio that
you are playing. This makes it easier to hear the audio that is playing.
Setting the Sound Quality for Giving a Presentation If [Narration] is specified for the sound quality, the projector plays dialog clearly. This mode is useful
when you give a presentation using the microphone connected to the projector, for example.
1. Press the [Sound] button. The sound quality selection screen appears at the bottom of the screen.
2. Select [Narration] ( ) using the [ ] and [ ] buttons.
Setting the Sound Quality for Playing Music If [Music] is specified for the sound quality, the projector plays music dynamically. This mode is useful for
music videos, for example. This mode is also useful if you want to decorate a shop window with video
and music.
1. Press the [Sound] button. The sound quality selection screen appears at the bottom of the screen.
2. Select [Music] ( ) using the [ ] and [ ] buttons.
4. Useful Functions
62        
						

							5. Using the Projector via a Network
This chapter explains the settings for using the projector via a network. This chapter also explains the
operations that use QuickProjection.
Before Connecting to a Network
The projector does not support the Windows Vista and Windows 7 Network Projector function. Use
QuickProjection, which is the application provided with the projector for projecting images via a
network. For details about QuickProjection, see page 73 "Projecting a Computer's Screen via a
Network".
Connecting an Ethernet Cable • Do not place the power cord and connection cable in a way that might cause someone to trip
and fall. The machine might fall over and cause an injury. The projector is compatible with 10BASE-T, 100BASE-TX, and 1000BASE-T Ethernet interfaces.
Status of the network connection
You can confirm the status of the network connection by the patterns in which the LEDs on the
Ethernet interface light up. If the projector is not connected to a network, no LEDs light up. 1. When 1000BASE-T is active (orange and green LEDs light up)
2.
When 100BASE-TX is active (orange LED lights up)
3.
When 10BASE-T is active (green LED lights up)
63 
CLB072
123   
						

							1.
Insert the Ethernet cable into the Ethernet interface. 2.
Connect the other end of the Ethernet cable to a network device such as a hub. • The use of a shielded LAN cable is recommended.
Precautions for Using a Wireless LAN • Do not use a wireless LAN if there is electromagnetic interference from other equipment. Doing
so may cause an accident due to the other equipment malfunctioning from the electromagnetic
interference. Wireless uses radio waves to exchange information instead of an Ethernet cable. The wireless LAN
radio waves pass through barriers such as walls within a fixed area, so the following problems may
occur:
Leak of Personal Information
•Information such as IDs, passwords, credit card numbers, and the contents of e-mails, etc.,
may be stolen by a third party.
Illegal Access to the Network
•
Data and systems may be corrupted or manipulated by a virus.
• An imposter may access information illegally.
• Confidential information may be accessed illegally.
To minimize the possibility of these problems occurring, it is recommended to check the functions built
into the wireless LAN devices, such as the projector and wireless LAN access points, and to specify
security settings. • (mainly Europe and Asia)
5. Using the Projector via a Network
64
CZE122       
						

							The projector does not support the 5 GHz band.
• (mainly North America)
The projector supports 40 MHz channels only in the 5 GHz band and in the infrastructure mode. Before Connecting to a Network
65   
						

							Connecting the Projector to a Network
To connect the projector to a network, you must specify network settings such as an IP address. The
required settings differ depending on the network environment and how you use the projector.
You can configure the required settings easily by using Network Setting Wizard. For details about how
to open Network Setting Wizard, see page 67 "Opening Network Setting Wizard".
To connect to a wired LAN
Connect an Ethernet cable to the projector, and then configure the network settings in [Wired LAN]
on Network Setting Wizard. For details about how to configure the wired LAN network settings,
see page 67 "Configuring the Wired LAN Settings".
To connect to a wireless LAN in infrastructure mode
In infrastructure mode, the projector can communicate with networks in which both wireless and
wired LAN devices are connected via a wireless LAN access terminal. It is necessary to user
greater security since all communication is via a network. Use infrastructure mode in environments
in which a wireless LAN has already been configured.
Configure the network settings in [Wireless LAN (Infrastructure)] on Network Setting Wizard. The
setting method differs depending on the network environment.• Configuring the settings by Simple Wireless LAN Setup
If the access point is compliant with the simple wireless LAN setup function, you can configure
the network settings easily. This function acquires the wireless LAN settings registered in the
access point, and configures those settings for the projector automatically. You can configure
the settings without entering the SSID and the network key manually. For details, see
page 68 "Configuring the settings by Simple Wireless LAN Setup".
•
Configuring the settings manually
You can configure the network settings by selecting the network to connect to from the
available network list. Up to 10 networks are displayed in the list in radio field intensity order.
If you want to connect to a network that is not displayed in the list or is not broadcasting its
SSID, enter the SSID manually. For details, see page 70 "Configuring the settings
manually".
To connect to a wireless LAN in ad hoc mode
In ad hoc mode, the projector can communicate with the computer directly, and not via an access
point. No other equipment is required, so this mode is suited for locations that have no network
environment. As the radio wave range is limited, use an office or conference room with a good line
of sight.
Configure the network settings in [Wireless LAN (Adhoc)] on Network Setting Wizard. For details
about how to configure the network settings for a wireless LAN in ad hoc mode, see page 71
"Configuring the Wireless LAN Settings for Ad Hoc Mode".
5. Using the Projector via a Network
66  
						

							• If your wireless LAN access point uses WPA/WPA2-EAP as the authentication method, you must
set the current date and time and the time zone of the location where the projector is installed. For
details, see page 120 "Default Settings 2 Menu".
Opening Network Setting Wizard You can open Network Setting Wizard on the menu screen.
• If you configure both wired and wireless LAN settings using the Network Setting Wizard and your
wireless LAN access point uses WPA/WPA2-EAP as the authentication method, it is recommended
that you configure the wired LAN settings first.
1. Press the [Menu] button.
2. Select [Network/USB Settings], and then press the [ ] button.
3. Select [Network Settings], and then press the [Enter] button.
4. Select [Setup Wizard], and then press the [ ] button.
5. Select [Network Setting Wizard], and then press the [Enter] button.
If Administrator Authentication is enabled, enter the password, and then press the [Enter] button.
The Network Setting Wizard appears. Configuring the Wired LAN Settings
Connect an Ethernet cable to the projector before configuring the settings.
Contact your network administrator for the information required for configuring network settings. Connecting the Projector to a Network
67      
						

							1.
Select [Wired LAN] on Network Setting Wizard, and then press the [Enter] button. 2.
Select [Disable DHCP (Manual Settings)] or [Enable DHCP (Auto Settings)], and then press
the [Enter] button.
If you select [Enable DHCP (Auto Settings)], proceed to Step 6.
3. Specify the projector's IP address.
4. Specify the subnet mask.
5. Specify the default gateway.
6. Select [Continue Wizard] or [End Wizard] on the confirmation screen, and then press the
[Enter] button.
To proceed to the wireless LAN settings, select [Continue Wizard]. For details about how to
configure the wireless LAN settings, see page 68 "Configuring the Wireless LAN Settings for
Infrastructure Mode", or page 71 "Configuring the Wireless LAN Settings for Ad Hoc Mode".
To end the network settings, select [End Wizard].
The wired LAN setup is complete.
To project the image from a computer, see page 73 "Projecting a Computer's Screen via a
Network".
Configuring the Wireless LAN Settings for Infrastructure Mode Configuring the settings by Simple Wireless LAN Setup
The projector supports the following simple wireless LAN setup method. Contact your network
administrator for the available simple wireless LAN setup method in your network environment and the
information required for configuring network settings.
Setup Method
•Using push buttons
Press the projector and access point keys or buttons to get them to connect to each other and
register the settings.
5. Using the Projector via a Network
68