Ricoh Projector PJ WX4152NI User Manual

							4.
Install the computer USB adapter into the computer. When the registered computer USB adapter is installed into the computer, the adapter flickers once
every 0.5 seconds. Then, when the computer USB adapter is connected to the projector, the
adapter flickers once every two seconds. If the adapter flickers twice every 0.5 seconds, you need
to register it on the projector.
To make registration, see page 85 "Registering the Computer USB Adapter".
5. Turn the power switch of the electronic pen to "On". The communication indicator on the electronic pen will then flicker.
If the communication indicator fails to flicker, check that the rechargeable battery is installed in the
electronic pen. If a battery is installed, recharge it. For about the electronic pen, see page 93
"Using the Electronic Pen". Preparations for Using the Interactive Function (RICOH PJ WX4152NI only)
89
CWD013 
CWD011   
						

							6.
Point the pen nib toward the projected screen. • If registration succeeds
The projected computer screen pointer moves according to the movements of the electronic
pen. Also, the communication indicator on the electronic pen lights up or flickers green rapidly
and the computer USB adapter lights up.
• If registration fails
•
Check how you are holding the electronic pen. If you are holding the top or the bottom
of the pen, the projector is unable to recognize the electronic pen correctly. To hold the
electronic pen correctly, see page 94 "How to Use the Electronic Pen".
• Check that the pen nib is not pointing at a shadow. If the pen nib is pointing at a shadow or if it is not pointing at the screen, then the projector is unable to recognize the
electronic pen correctly. To operate the electronic pen correctly, see page 94 "How to
Use the Electronic Pen".
• If the electronic pen is not recognized correctly after the direction of the pen is corrected or even when you hold the electronic pen correctly, check the procedure from Step 1 by
referring to page 99 "When You Cannot Use the Interactive Function".
Installing RICOH PJ Interactive Software RICOH PJ Interactive Software allows you to write and draw on a projection screen. When you use
RICOH PJ Interactive Software, install it on a computer. For details about how to use RICOH PJ
Interactive Software, see Operating Instructions (Interactive Function).
The following operating environment is required to use RICOH PJ Interactive Software.
Item
Specifications
CPU • Intel®
 Core TM
2 Duo 2 GHz or more recommended
(Minimum: Intel Core Solo U1300) 6. Using the Interactive Function (RICOH PJ WX4152NI only)
90
CZE028   
						

							Item
Specifications
Memory • Windows 7 / 8 (32 bit): 3 GB or more recommended (Minimum: 1 GB)
•Windows 7 / 8 (64 bit): 4 GB or more recommended (Minimum: 2 GB)
•
Windows 8.1 (32 bit): 3 GB or more recommended (Minimum: 1 GB)
• Windows 8.1 (64 bit): 4 GB or more recommended (Minimum: 2 GB)
• Windows 10 (32 bit): 3 GB or more recommended (Minimum: 1 GB)
• Windows 10 (64 bit): 4 GB or more recommended (Minimum: 2 GB)
HDD • 9 GB or more free space recommended (Minimum: 2 GB)
Operating System • Windows 7 Home Premium / Professional / Ultimate / Enterprise SP1 or later (32 bit / 64 bit)
• Windows 8 / Pro / Enterprise (32 bit / 64 bit)
•

Windows 8.1 / Pro / Enterprise (32 bit / 64 bit)
• Windows 10 Home / Pro / Enterprise / Education (32 bit / 64 bit) • To install RICOH PJ Interactive Software on a computer, log on as a user with administrator
privileges.
1. Insert the CD-ROM in the CD-ROM drive of your computer.
2. Specify a language and model name, and then click [Select].
3. Click [PJ Interactive Software].
4. Select the language for the installation, and then click [OK].
5. If .NET Framework 4 is not installed on your computer, click [Install].
If .NET Framework 4 has already been installed, the message [Install] does not appear. Proceed to
the next step.
6. Click [Next].
7. Select "I accept the terms in the license agreement", and then click [Next].
8. Specify the installation folder, and then click [Next].
9. Click [Install].
10. Click [Finish]. • If the [User Account Control] dialog box appears during the installation procedure, click [Yes] or
[Continue]. Preparations for Using the Interactive Function (RICOH PJ WX4152NI only)
91    
						

							• To uninstall RICOH PJ Interactive Software, use the program delete function in [Control Panel] to
delete "RICOH PJ Interactive Software".
6. Using the Interactive Function (RICOH PJ WX4152NI only)
92  
						

							Using the Electronic Pen
This section introduces the names of the parts of the electronic pen and explains how to charge it.
After you finish setting up the interactive function, insert the computer USB adapter into the computer.
After the computer recognizes the electronic pen, you can use it to perform operations on the projected
screen. For details about the electronic pen, see page 88 "Enabling the Projector to Recognize the
Electronic Pen".
Communication between the electronic pen, the projector, and the computer USB adapter is conducted
wirelessly. Do not block the area between the electronic pen, projector, and computer. In addition, do
not use wireless devices near the electronic pen. Otherwise, the position of the electronic pen will not be
recognized correctly.
Electronic Pen Parts and Their Functions
1. Pen nib switch
Used to write, draw, and select operations on the projected screen. This switch is functionally equivalent to the
left button of a computer mouse.
2. Left button
Similar to the left button of a computer mouse.
3.
Right button
Similar to the right button of a computer mouse.
4. Point adjustment button Used to adjust the point position of the pen nib when the pen is held in a different way. The standard position
of the point is the center of the pen, and it moves each time this button is pressed. The order in which the point
moves is as follows: up, down, and to the center.
5. Battery indicator Indicates the battery status of the electronic pen.
The battery indicator keeps lighting while charging and goes off when the charge is completed.
6. Communication indicator Indicates the communication status of the electronic pen.
This indicator flickers in red until the projector recognizes the electronic pen. Using the Electronic Pen
93
CWD008
1                        2   3   4    5  67        8   
						

							When the projector recognizes the electronic pen, the indicator lights up in green or flickers rapidly.
7. USB connecter
Used to connect the electronic pen charge cable. See page 98 "Recharging the Electronic Pen".
8.
Power switch
Switches the power of the electronic pen between on and off.
How to Use the Electronic Pen When the pen nib is pointed toward the screen projected by the projector in Interactive Mode, the
electronic pen is recognized and the pointer on the projected computer screen can be operated with the
electronic pen. See page 88 "Enabling the Projector to Recognize the Electronic Pen".
You can operate the computer projection screen by touching it with the pen nib—you can select an icon
or menu, or write and draw. You may also touch the pen nib twice on the same position of the screen,
much like the double-click of a mouse.
• Operate the electronic pen so that the pen nib does not point toward a shadowed area.
When the projector is installed on a table or the floor
Hold the electronic pen as shown below. If the nib or bottom of the electronic pen is held, the
position of the electronic pen will not be recognized correctly. 6. Using the Interactive Function (RICOH PJ WX4152NI only)
94 
CWD014 
CZD017   
						

							To align the point position of the electronic pen with the pen nib switch, and not the center of the
pen, use the point adjustment button to move the point position up.
When the projector is installed on a wall or ceiling
When the projector is installed on a wall or ceiling, hold the electronic pen upside down to
eliminate the shadow that appears on the screen. To align the point position with the pen nib switch while holding the electronic pen upside down,
use the point adjustment button to move the point position down.
Operating the electronic pen remotely
You can also operate the screen remotely. When standing away from the screen, use the mouse
button on the electronic pen. Using the Electronic Pen
95
CWD030 
CWD024 
CWD032   
						

							• The electronic pen can only be used while the projector is in Interactive Mode. For details about
how to configure the projector, see page 84 "Enabling Interactive Mode".
Installing a Rechargeable Battery into the Electronic Pen • For safe operation, follow the warnings below regarding the batteries. If you use the batteries
incorrectly, it may result in fire or injury due to batteries leaking or exploding.
• Do not use batteries other than the ones specified.
•
Do not mix and use batteries that are different types or that are new and old.
• Correctly insert batteries according to the polarity (  /  ).
• Do not charge non-rechargeable batteries.
•

Do not heat or throw the batteries into fire or water.
• Do not connect the positive and negative terminals on a battery with a wire.
• Remove the batteries that are past their suggested use period or that are depleted.
• Remove the batteries when they will not be used for extended periods.
• Keep the batteries out of the reach of children. Children may swallow or choke on the batteries. If this happens, contact a doctor immediately. 6. Using the Interactive Function (RICOH PJ WX4152NI only)
96
CZE127       
						

							1.
Check the electronic pen to make sure that the power is off. 2.
Push down A and slide the battery cover to remove it. 3.
Install a battery.
Check that the battery has been installed in the right direction. Using the Electronic Pen
97
CWD029 
A                 
CWD025 
CWD026   
						

							4.
Re-install the battery cover. • For details about what to do if a battery has leaked, see page 153 "Operating Precautions".
Recharging the Electronic Pen Insert an electronic pen charge cable into a USB port on the computer and connect the electronic pen.
The battery indicator keeps lighting while charging and goes off when the charge is completed. 6. Using the Interactive Function (RICOH PJ WX4152NI only)
98
CWD027  
CWD009