Ricoh Projector PJ WX2240 User Manual

							English
39
English
User Settings
 V. Position (Vertical Position)
 Shift the projected image position vertically.
  Press the  key to move the image down.
  Press the  key to move the image up.
 Digital Zoom
 Adjust the digital zoom ratio of the projected image.
  Press the  key to reduce the size of an image.
  Press the  key to magnify an image on the projection screen.
 V. Keystone
 Press the  or  key to adjust image distortion vertically. If the 
image looks trapezoidal, this option can help make the image 
rectangular.
 Projection Mode
 Use this function to select the projector mode, depending upon 
how the projector is mounted.
   Front: This is the default selection. The image is projected 
straight on the screen.
   Front Ceiling: When selected, the image will turn upside down.
   Rear: When selected, the image will appear reversed.
   Rear Ceiling: When selected, the image will appear reversed in 
upside down position.
  RGB Input Range
 Adjust the color range of the HDMI image data.
   Auto: Automatically detect RGB range.
   Standard: Process the input image as standard color range data.
   Full: Select this mode when computer signal or full range signal 
from AV equipment is input.
	“RGB Input Range” is only supported under HDMI source.
Note     
						

							40
English
User Settings
SETTING
 Language
 
Choose the multilingual OSD. Press “Enter” to open the sub menu 
and then use the  or  or  or  key to select your preferred 
language. Press “Enter” to finalize the selection. 
 Monitor Out (Standby)
  Enable/Disable the Monitor output function.
   On: Enable the Monitor Out function at projector standby status.
   Off: Disable the Monitor Out function at projector standby 
status.
  Reset
  Return the adjustments and settings to the factory default values.
Choose “Yes” to return the display parameters on all menus except \
Language and Lamp Hours Used to the factory default settings.
	Monitor Out function is not available on RICOH PJ S2240.
Note     
						

							English
41
English
User Settings
VOLUME  
(PJ X2240 / PJ WX2240)
 Mute
 
Temporarily turn off the sound.
  Choose “On” to mute the sound.
  Choose “Off” to turn mute off.
 Volume
  Adjust the volume level.
  Press the  key to decrease the volume.
  Press the  key to increase the volume.
	“Mute” function affects both internal and external speaker volume.
Note     
						

							42
English
User Settings
OPTIONS
 Auto Source
 
When this function is turned “On”, the projector will search for 
other signals if the current input signal is lost. When this function is\
 
turned “Off”, it will only search a specified connection port.
 Input
Use this option to enable/disable input sources. Press the ► key 
to enter  the sub menu and select which sources you require. Press 
“Enter” to finalize the selection. The projector will only search for 
inputs that are enabled.
 Auto Power Off (Min)
 
Sets the countdown timer interval. The countdown timer will start, 
when there is no signal being sent to the projector. The projector 
will automatically power off when the countdown has finished (in 
minutes).
	Default value of “Auto Power Off (Min)” is 20 min.
Note     
						

							English
43
English
User Settings
 Lamp Settings
 
Use this option to view the lamp life status and configure the lamp 
settings. Press the ► key to enter the sub menu and configure the 
desired settings.
   Lamp Hours Used (Normal): Display the projection time.
Lamp Hours Used in Eco mode or “Image Eco” mode “On” will 
be converted to Lamp Hours Used in “Normal” mode.
   Lamp Life Reminder: Choose this function to show or to hide 
the warning message when the changing lamp message is 
displayed. The message will appear 30 hours before suggested 
replacement of lamp. 
   Lamp Power Mode: Set the brightness mode. Choose “Normal” 
to increase the brightness or choose “ECO” to dim the projector 
lamp which will lower power consumption and extend the 
lamp life.
   Image Eco: Choose “On” to dim the lamp power, depending on 
the brightness level of images, and significantly reduce the lamp 
power consumption. The lamp life will be extended.
 High Altitude
 
When “On” is selected, the fans will spin faster. Set High Altitude 
mode to “On” when the projector is used over 2500ft (750m) 
elevation.
	When ambient temperature is over 40°C in operating, the projector will switch to “ECO” automatically.
Note     
						

							44
English
User Settings
 Dust Filter Reminder
 
Use this option to view the filter status and configure the filter 
settings. Press the ► key to enter the sub menu and configure the 
desired settings.
This item is disabled for the projector sold in some regions.
   Filters Remind (Hour): Set the maximum filter time usage.
   Cleaning Up Reminder: Choose this function to show or hide 
the warning message when the changing filter message is 
displayed.
If the reminder function is enabled and the usage time reached 
its limit, a message will appear on the screen to remind you to 
clean or change the filter.
 Information
 
Display the projector information.
   Source: Display the input source that is currently connected to.
   Resolution: Display the resolution setting of the current input 
source.
   Software Version: Display the firmware version.
   Color Space: Display the currently used color matrix type.
   Aspect Ratio: Display the currently used aspect ratio setting.     
						

							English
45
English
User Settings
3D
 3D
 
Use this option to enable/disable the 3D function. 
 Off: Choose “Off” to display normal (2D) picture.
 On: Choose “On” to display 3D format.
 3D Sync Invert
  Use this option to enable/disable the 3D sync invert function.
 Off: Choose “Off” for default frame contents.
  On: Choose “On” to invert left and right frame contents. Choose 
“On” if viewing image is not natural or felt 3D incorrect. 
 3D Format
  Use this option to select the appropriate 3D format content.
  Side-by-Side: Use this mode for “Side-by-side” format 3D 
content.
  Top and Bottom: Use this mode for “Top and Bottom” format 3D 
content.
  Frame Sequential: Use this mode for “Frame Sequential” format 
3D content.
	Compatible 3D source, 3D content and Optical 3D glasses Type 2 is required for 3D viewing.
	“3D Sync Invert” is only available when 3D is enabled.
	This setting may need to change when re-start running 3D 
movie. 
	3D function is turned on automatically when Blu-ray 3D source is input. 
Note     
						

							46
English
Troubleshooting
Problem: No image appears on screen
  Ensure all the cables and power connections are correctly and 
securely connected as described in the “Installation” section.
 Ensure the pins of terminals are not crooked or broken.
  Check if the projection lamp has been securely installed. Refer to 
the “Replacing the lamp” section section for more information.
  Make sure you have removed the lens cap and the projector is 
switched on.
  Ensure that the “AV Mute” feature is not turned on.
Problem: Partial, scrolling or incorrectly displayed image
  Press “Auto Set” on the remote control.
   Adjust the computer display settings. Verify the resolution setting 
is less than or equal to 1600 x 1200 resolution. See your operating 
system’s Help file.
 If you are using a Notebook:
  1.   First, follow the steps above to adjust resolution of the 
computer.
  2. Press the toggle output settings. For example: [Fn]+[F3]
PANASONIC, NEC => Fn+F3 
HP, SHARP, TOSHIBA => Fn+F5
IBM, SONY => Fn+F7
DELL, EPSON => Fn+F8
FUJITSU => Fn+F10
APPLE =>F7
   If you experience difficulty changing resolutions or your monitor 
freezes, restart all equipment including the projector.
If you experience trouble with the projector, refer to the 
following information. If the problem persists, please contact 
your local dealer or service center.     
						

							English
47
English
Troubleshooting
Problem: The screen of the Notebook computer is not 
displaying a presentation
 If you are using a Notebook PC:
   Some Notebook PCs may deactivate their own screens when a 
second display device is in use. Each has a different way to be 
reactivated. Refer to your computer’s documentation for detailed 
information.
Problem: Image is unstable or flickering
  Adjust the “Phase” or “Clock” to correct it. Refer to the  
“H. Position” or “V. Position” section for more information.\
   Check and reconfigure the display mode of your graphic card to 
make it compatible with the product. 
Problem: Image is out of focus
 Adjust the Focus Ring on the projector lens. 
   Make sure the projection screen is between the required distance. 
(refer to pages 33~34)
Problem: The image is stretched when displaying 16:9 DVD
Change the aspect ratio by pressing the “Aspect” button on the 
remote control or select “SCREEN > Aspect Ratio” from the OSD 
menu to show image with proper aspect ratio. 
Problem: Image is too small or too large
   Adjust the Zoom lever on the top of the projector.
   Move the projector closer to or further from the screen.
   Press the “Aspect” button on the remote control or press the 
“Menu” button on the projector panel, go to “SCREEN > Aspect 
Ratio” and try the different settings.     
						

							48
English
Troubleshooting
Problem: Image is reversed
   Select “SCREEN > Projection Mode” from the OSD menu to ad-
just the image.
Problem: Lamp burns out or makes a popping sound
   When the lamp reaches its end of life, it will burn out and may 
make a loud popping sound.  If this happens, the projector will 
not turn on until the lamp module has been replaced. To replace 
the lamp, follow the procedures in the “Replacing the Lamp”.