Ricoh Projector PJ WX2240 User Manual

English
29
English
Basic Operations
Powering On the Projector
1. Ensure that the power cord and signal cable are securely 
connected. The Power indicator will turn red.
2.   Remove the lens cap (PJ X2240 / PJ WX2240). 
3.   Turn on the lamp by pressing the “” button on the control 
panel or the remote control.  The Power indicator will 
flash blue.
 The startup screen will display in approximately 5 seconds. 
After the screen disappears, the Power indicator will turn 
blue.  
4.   The first time you...

30
English
Basic Operations
Powering Off the Projector
1.    Press the “” button and you will see a message as below on 
the on-screen display.
 
2.   Press the “” button again to turn off the projector lamp.
3.   The cooling fan continues to operate for about 30 seconds for 
cooling cycle and the Power indicator will flash red. After 
cooling down, the light stops flashing, and then the projector 
will enter the standby mode.
   If you wish to turn the projector back on, you must wait 
until the...

English
31
English
Basic Operations
Warning Indicator
   When the “Temp” indicator lights red, it indicates the 
projector has overheated. The projector will automatically 
shut itself down.
 
   When the “Lamp” indicator lights red, and you see the 
message below displays on-screen, the projector has 
detected that the lamp is approaching its end of life. Please 
change the lamp as soon as possible or contact your local 
dealer or our service center. 
 
   When the “Temp” indicator flashes red (0.5...

32
English
Basic Operations
Adjusting the Projected Image
Adjusting the Position of Projector Image
The projector is equipped with adjustable feet to raise and lower 
the image to fill the screen.
1.   Locate the adjustable foot you wish to modify on the 
underside of the projector.
2.   Rotate the adjustable ring clockwise to raise the projector 
or counter clockwise to lower it. Repeat with the 
remaining feet as necessary.
	You can raise the projector front up to 6.5° by rotating the adjustable...

English
33
English
Basic Operations
Focus Ring
Adjusting the Projector Zoom and Focus
You may turn the zoom lever to zoom in or out. To focus the 
image, rotate the focus ring until the image is clear. 
 
RICOH PJ S2240/PJ X2240: Focus at distances from 3.94 to 
39.4 feet (1.2 to 12.0 meters).
 
RICOH PJ WX2240: Focus at distances from 3.28 to 32.8 feet 
(1.0 to 10.0 meters).
Adjusting Projection Image Size
Zoom Lever
Width
Height
Diagonal
Side ViewProjection Distance (D)Screen
Screen (H)
Offset (Hd)
...

34
English
Basic Operations
This table is for user’s reference only.
Diagonal length (inch) size of 4:3 Screen
Screen Size W x HProjection Distance (D)Offset (Hd)(m)(inch)(m)(feet)
WidthHeightWidthHeightwidetelewidetele(m)(feet)
300.61 0.46 24.00 18.00 1.19 1.31 3.90 4.30 0.07 0.23 
400.81 0.61 32.00 24.00 1.58 1.75 5.20 5.73 0.09 0.30 
601.22 0.91 48.00 36.00 2.38 2.62 7.80 8.60 0.14 0.45 
701.42 1.07 56.00 42.00 2.77 3.06 9.10 10.03 0.16 0.52 
801.63 1.22 64.00 48.00 3.17 3.50 10.40 11.47 0.18 0.60...

English
35
English
User Settings
The Projector has a multilingual On Screen Display that 
allows you to make image adjustments and change a variety of 
settings.
How to operate
1.   To open the OSD, press “Menu” on the Control Panel or Remote 
Control.
2.  When OSD is displayed, use      keys to select any item in the 
main menu. While making a selection on a particular page, press   
  or “Enter” key to enter sub menu.
3.  Use      keys to select the desired item in the sub menu and 
press     or...

36
English
User Settings
PICTURE
 Picture Mode
  There are many factory presets optimized for various types of 
images. Use the  or  key to select the item. 
  Bright: Mode for emphasizing brightness.
   Standard: Mode for optimizing the balance between brightness 
and color reproduction.
   Game: For game content.
  Natural: Mode for emphasizing color reproduction.
   User: User defined settings.
  Wall Color
  Use this function to obtain an optimized screen image according to 
the wall color. The...

English
37
English
User Settings
 Contrast
  The contrast controls the degree of difference between the lightest 
and darkest parts of the picture. Adjusting the contrast changes the 
amount of black and white in the image.
  Press the  key to decrease the contrast.
  Press the  key to increase the contrast.
  Sharpness
 Adjust the sharpness of the image.
  Press the  key to decrease the sharpness.
  Press the  key to increase the sharpness.
 Saturation
  Adjust the color saturation of the image.
 ...

38
English
User Settings
	“H. Position” and  “V. Position” functions are only supported under Computer Signal source.
Note
SCREEN
 Aspect Ratio
 Use this function to choose your desired aspect ratio.
   Auto: Automatically selects the appropriate display format. 
When input is 4:3, the image is displayed as 4:3. When input is 
16:9 above, the image is displayed as 16:9.
   4:3: This format is for 4x3 input sources.
   16:9: This format is for 16x9 input sources, like HDTV and DVD 
enhanced for...