Ricoh Projector PJ S2240 User Manual

							49
 Reset
  Return the adjustments and settings to the factory default values.
Choose “Yes” to return the display parameters on all menus 
except Language and Lamp Hours Used to the factory default 
settings. LAN Control settings also return to the factory default. 
Set again after reset.
English 
English
User Settings
English   
						

							50
Volume
 Mute
 
Temporarily turn off the sound.
  Choose “On” to mute the sound.
  Choose “Off” to turn mute off.
 Volume
  Adjust the volume level.
  Press the  key to decrease the volume.
  Press the  key to increase the volume.
	“Volume” menu is not available on RICOH PJ S2240/RICOH PJ TS100.
Note
	“Mute” function affects both internal and external speaker volume.
Note 
English
User Settings   
						

							51
Options
 Auto Source
 
When this function is turned “On”, the projector will search for 
other signals if the current input signal is lost. When this function is\
 
turned “Off”, it will only search a specified connection port.
 Input
Use this option to enable/disable input sources. Press the ► key 
to enter the sub menu and select which sources you require. Press 
“Enter” to finalize the selection. The projector will only search for 
inputs that are enabled.
 Auto Power Off (Min)
 
Sets the countdown timer interval. The countdown timer will start, 
when there is no signal being sent to the projector. The projector 
will automatically power off when the countdown has finished (in 
minutes). When countdown timer is selected to “0”, auto power off 
is disabled.
	Default value of “Auto Power Off (Min)” is 20 min.
Note
English 
English
User Settings
English   
						

							52
 Lamp Settings
 
Use this option to view the lamp life status and configure the lamp 
settings. Press the ► key to enter the sub menu and configure the 
desired settings.
   Lamp Hours Used (Normal): Display the projection time.
Lamp Hours Used in Eco mode or “Image Eco” mode “On” will 
be converted to Lamp Hours Used in “Normal” mode.
   Lamp Life Reminder: Choose this function to show or to hide 
the warning message when the changing lamp message is 
displayed. The message will appear 30 hours before suggested 
replacement of lamp. 
   Lamp Power Mode: Set the brightness mode. Choose “Normal” 
to increase the brightness or choose “ECO” to dim the projector 
lamp which will lower power consumption and extend the 
lamp life.
  Image  Eco: Choose “On” to dim the lamp power, depending 
on the brightness level of images, and significantly reduce the lamp 
power consumption. The lamp life will be extended.
 High Altitude
 
When “On” is selected, the fans will spin faster. Set High Altitude 
mode to “On” when the projector is used over 2500ft (750m) 
elevation.
	When ambient temperature is over 40°C in operating, the projector will switch to “ECO” automatically.
Note 
English
User Settings   
						

							53
 Dust Filter Reminder
 Use this option to view the filter status and configure the filter settings. Press the ► key to enter the sub menu and configure the desired settings.
This item is disabled for the projector sold in some regions.
   Filters Remind (Hour): Set the maximum filter time usage.
   Cleaning Up Reminder: Choose this function to show or hide the warning message when the changing filter message is displayed.
If the reminder function is enabled and the usage time reached its limit, a message will appear on the screen to remind you to 
clean or change the filter.
 Information
 
Display the projector information.
   Source: Display the input source that is currently connected to.
   Resolution: Display the resolution setting of the current input 
source.
   Software Version: Display the firmware version.
   Color Space: Display the currently used color matrix type.
    Aspect  Ratio: Display the currently used aspect ratio setting.
English 
English
User Settings
English   
						

							54
3D
 3D
 
Use this option to enable/disable the 3D function. 
 Off: Choose “Off” to display normal (2D) picture.
 On: Choose “On” to display 3D format.
 3D Sync Invert
  Use this option to enable/disable the 3D sync invert function.
 Off: Choose “Off” for default frame contents.
  On: Choose “On” to invert left and right frame contents. Choose 
“On” if viewing image is not natural or felt 3D incorrect. 
 3D Format
  Use this option to select the appropriate 3D format content.
  Side by Side: Use this mode for “Side by Side” format 3D 
content.
  Top and Bottom: Use this mode for “Top and Bottom” format 3D 
content.
  Frame Sequential: Use this mode for “Frame Sequential” format 
3D content.
	Compatible 3D source, 3D content and Optical 3D glasses Type 2 is required for 3D viewing.
	“3D Sync Invert” is only available when 3D is enabled.
	This setting may need to change when re-start running 3D movie. 
	3D function is turned on automatically when Blu-ray 3D source is input. 
Note 
English
User Settings   
						

							55
How to use web browser to control 
your projector
Connecting to the projector
1. Check IP address of the projector
Check IP address in “Settings” > “Network” in the projector \
menu system. (See page 44 on the projector user’s manual).
2. Connect
Open your web browser and type in the IP address you checked. 
For example, type “http://192.168.0.100” when IP address is 
displayed as the screen above.
Login
1. The web browser shows a login page
	If you want to connect an existing network system, consult the network administrator for network settings.
	Network settings such as password will be reset when you set “Default settings 2” > “Reset All” in the projector menu system.
	In rare cases, the network function won’t work properly due to electrostatic discharge or something. Set “Default settings 2” > “Reset All” in such a case.
Note
	This web pages use Java Script. Please turn on Java Script in your browser.
Note
English 
English
LAN Control
English   
						

							56
	The warning message “Invalid Character” will popup if your password is incorrect.
	“B01” showed in the top in the web page picture indicates software version of this web page. It may be different from “B01”.
Note
2. Select a user
You can use all functions (Control Panel, Network setting and 
Alert setting) when you select “administrator”. And you can use 
only “Control Panel” when you select “user”.
3. Enter the Password
If the password setting is enabled the correct password needs to 
enter.
Default passwords of Administrator: “admin”
Default passwords of User: “user”
If the password setting is disabled the “Password” item will be 
gray out.
Click [Login] button to login.
4. Login
After login, control tabs will appear. It contains Home, Control 
Panel, Network Setting, Alert Setting, and Logout.
Home is automatically selected after login. 
English
LAN Control   
						

							57
Home
This is Home page which shows basic information of your 
projector. There is no control on this page.
1. Projector Status
System Status:
It shows the current system status of the projector. It includes 
Standby, Warm-up, Power-on, cooling, Power-off and 
Unknown.
-Input:
[PJ X5460][PJ WX5460]
It shows the current input source of the projector. It includes 
Computer 1, Computer 2, S-Video, Video, HDMI, None and 
Unknown.
-Lamp Hours: 
It shows the current lamp hours of the projector.
-FW Version: 
It shows the current firmware version of the projector.
English 
English
LAN Control
English   
						

							58
Projector Control Panel
This page shows the control items of your projector. User can 
control the projector by this page.
Control Buttons
Execute a function when the button is clicked.
[Power ON]Power is turned on.
[Power OFF]Power is turned off.
[Auto Set]Automatically adjust the RGB signal from the computer.
[Input]Switch among Computer1, Computer2, Video, S-Video, and HDMI.
Setting Buttons
Setting is toggled On and Off by clicking the button.
[Auto Source]Search the next signal source automatically when the current signal is lost. 
(See p.47 on the Projector User's manual)
[AV Mute]Momentarily turn off the audio and video.
[Freeze]Pause the screen image.
[3D Projection]Set 3D projection mode on.
[L/R Reverse]Change left and right frame content of 3D projection.
(See p.50). 
English
LAN Control