Ricoh Projector PJ S2240 User Manual

29
Connect to Computer/Notebook
1
5
6
11
15 101
5
6
11
15 10
Monitor 
Out(
Comp .1)
Audio 
1 In
S-V ideo  In
V ideo  In
Audio  2 In
Audio  OutCompu ter 2  In
Compu
ter 1 In
P C  Cont rol
Ser vice HDMI
LANE62405SP
R	Due to the difference in applications for each 
country, some regions may have different accessories.
Note
		To ensure the projector works well with your computer, 
please make sure the timing of the display mode is 
compatible with your projector. (See pages 76-79)
		Use the cables that...

30
RICOH PJ HD5450
E62405SP
R
43
Powered Speaker
2
5
(*)
6Router / Network Switch
1(*)
	Due to the difference in applications for each country, some regions may have different accessories.
Note
		To ensure the projector works well with your computer, 
please make sure the timing of the display mode is 
compatible with your projector. (See pages 76-79)
		Use the cables that come with the projector. (*)
	Make sure that the power plug is fully inserted into both the projector AC inlet and the wall...

31
1
5
6
11
15 10
E62405SP
R
	Due to the difference in applications for each country, some regions may have different accessories.
Note
1.........................................................................\
....................Power cord (supplied)2.........................................................................\
......................................HDMI cable 3.........................................................................\
..................Component-RGB...

32
1
5
6
11
15 101
5
6
11
15 10
E62405SP
R
	Due to the difference in applications for each country, some regions may have different accessories.
Note
1.........................................................................\
....................Power cord (supplied)2.........................................................................\
......................................HDMI cable 3.........................................................................\
..................Component-RGB...

33
1
5
6
11
15 101
5
6
11
15 10
Monitor 
Out(
Comp .1)
Audio 
1 In
S-V ideo  In
V ideo  In
Audio  2 In
Audio  OutCompu ter 2  In
Compu
ter 1 In
P C  Cont rol
Ser vice HDMI
LANE62405SP
R
	Due to the difference in applications for each country, some regions may have different accessories.
Note
1.........................................................................\
....................Power cord (supplied)2.........................................................................\...

34
	Due to the difference in applications for each country, some regions may have different accessories.
Note
	Make sure that the power plug is fully inserted into both the projector AC inlet and the wall outlet.
	The AC outlet must be near this equipment and must be easily accessible.
NoteConnect to AV Equipment
		Use the cables that come with the projector. (*)
	When HDMI input is selected, only audio signal with HDMI can be output.
	When Audio Out is connected, Built-in speaker doesn’t sound....

35
Powering On the Projector
1. Ensure that the power cord and signal cable are securely 
connected. The Power indicator will turn red.
2.   Remove the lens cap.  There is no lens cap on RICOH PJ 
S2240/PJ TS100.
3.   Turn on the lamp by pressing the “” button on the control 
panel or the remote control.  The Power indicator will 
flash blue.
 The startup screen will display and the Power indicator will 
turn blue.  
4.   The first time you use the projector, you will be asked 
to select the preferred...

36
Powering Off the Projector
1.    Press the “” button and you will see a message as below on 
the on-screen display.
 
Power Off?
Press power key again.
2.    Press the “” button again to turn off the projector lamp.
3.  The cooling fan continues to operate for about 30 seconds for 
cooling cycle and the Power indicator will flash red. After 
cooling down, the light stops flashing, and then the projector 
will enter the standby mode.
   If you wish to turn the projector back on, you must wait 
until...

37
Warning Indicator
  When the “Temp” indicator lights red, it indicates the 
projector has overheated. The projector will automatically 
shut itself down.
 
Warning! TEMPERATURE TOO HIGHPlease:
1. Make sure air in and outlets are not blocked.
2. Make sure the environment temperature is under 40 degree C.
  When the “Lamp” indicator lights red, and you see the 
message below displays on-screen, the projector has 
detected that the lamp is approaching its end of life. Please 
change the lamp as soon as...

38
Adjusting the Projected Image
Adjusting the Position of Projector Image
The projector is equipped with adjustable feet to raise and lower 
the image to fill the screen.
1.   Locate the adjustable foot you wish to modify on the 
underside of the projector.
2.   Rotate the adjustable ring clockwise to raise the projector 
or counter clockwise to lower it. Repeat with the 
remaining feet as necessary.
	You can incline the projector up to 6.5° by rotating the adjustable feet.
Note
Front Adjustable feet...