Ricoh Projector PJ KU12000 User Manual

71
Network
Configure the general network settings.
 `Projector Name: Display the projector hostname for Network.
 `Restart Network: Restart the network.
 `Network Factory Reset: Perform factory reset on the network settings. The 
Projector Name, LAN IP, and SNMP settings will be reset.
Serial Port Baud Rate
Select the serial port and baud rate.
Serial Port Echo
Control whether the serial port echoes characters.
Serial Port Path
Select the serial port path from either RS232 or HDBaseT.
Projector Address...

72
OPTION
Auto Source
High Altitude
Test Pattern
Background Color
Hot-Key settings
Power Settings
Light Source Settings
Light Sensor
Information
Factory ResetPICTUREOUTPUT SETUP
OPTION
OPTION
On
Off
Off
Logo
Blank Screen
Auto Source
 `On: The projector will search for other signals if the current input signal is lost.
 `Off: The projector will only search current input connection.
High Altitude
Set high altitude mode On/Off. When On, the fan will operate at high speed to 
ensure sufficient air flow for...

73
Light Sensor
Calibrate the Light Sensor for use with the Constant Luminance lamp mode, 
which allows the projector to be set for constant brightness. If the Light Sensor 
has not been calibrated, Constant Luminance mode will be disabled. Light Sensor 
calibration should be repeated when new lamps are installed.
Information
Display the projector information for source, resolution, and software version on the 
screen.
Factory Reset
Restore all settings to their default value. It will not reset network....

74
Auto Power Off
Sets the countdown timer. The countdown timer will start, when there is no signal 
being sent to the projector. The projector will automatically power off when the 
countdown has finished (in minutes).
Sleep Timer
Sets the countdown timer. The countdown timer will start, with or without a signal 
being sent to the projector. The projector will automatically power off when the 
countdown has finished (in minutes).
OPTION | Light Source Settings
Light Source Mode
Constant Power Settings...

75
Current Light Source
Select which lamp(s) is in use.
Auto Switch
Control when the projector switches lamps. Options include: on failure only, at 
power-up, or after a set number of hours.
Auto Switch Time (Hours)
Set the number of hours for Lamp Auto Switch.
For example:
1 Lamp conditions: lamp 1 = 50 hours, lamp 2 = 60 hours.
2 Set the current lamp to lamp 1 - the lamp with the lower lamp hour usage.
3 Set the Lamp Auto Switch to After (N) hours and the Lamp Auto Switch Time to 
100 hours.
4 When...

76
Troubleshooting
Appendices
If you experience a problem with your projector, please refer to the 
following information. If a problem persists, please contact your local \
reseller or service center.
Image Problems
  No image appears on-screen
 `Ensure all the cables and power connections are correctly and securely 
connected as described in the “Installation” section.
 `Ensure the pins of connectors are not crooked or broken.
 `Check if the projection lamp has been securely installed.
 `Make sure you...

77
 `If you are using a Notebook:
 -First, follow the steps above to adjust resolution of the computer.
 -Press the toggle output settings. example: [Fn]+[F4] 
Notebook BrandFunction  Keys
Acer[Fn]+[F5]
Asus[Fn]+[F8]
Dell[Fn]+[F8]
Gateway[Fn]+[F4]
IBM/Lenovo[Fn]+[F7]
HP/Compaq[Fn]+[F4]
NEC[Fn]+[F3]
Toshiba[Fn]+[F5]
Mac AppleSystem Preference -> Display -> Arrangement -> Mirror display
 `If you experience difficulty changing resolutions or your monitor freezes, 
restart all equipment including the...

78
  The image is stretched when displaying 16:10 DVD title
 `When you play anamorphic DVD or 16:10 DVD, the projector will show the 
best image when the projector display mode is set to 16:9 in the OSD.
 `If you play 4:3 format DVD titles, please change the format to 4:3 in the 
projector OSD.
 `If the image is still stretched, you will also need to adjust the aspect ratio by 
referring to the following:
 `Please setup the display format as 16:10 (wide) aspect ratio type on your 
DVD player.
  Image is...

79
Projector Problems
 
 The projector stops responding to all controls
 `If possible, turn off the projector, then unplug the power cord and wait at 
least 60 seconds before reconnecting power.
 
 Lamp burns out or makes a popping sound
 `When the lamp reaches its end of life, it will burn out and may make a loud 
popping sound. If this happens, the projector will not turn on until the lamp 
module has been replaced. To replace the lamp, follow the procedures in 
the “Replacing the Lamp” section....

80
Step 4: On the General tab, under This connection use the following 
items, click Internet Protocol(TCP/IP), and then click “Properties”.
Step 5: Click Use the following IP address, and type in as below:
1) IP address: 192.168.0.101
2) Subnet mask: 255.255.255.0
3) Default gateway: 192.168.0.254