Ricoh Mp C3000 Service Manual

 
SM 3-71 B230/B237/D042 
Replacement 
Adjustment 
1.  Rear cover ( Rear Cover) 
2.  Open the controller box. (
 Controller Box) 
3.  Drum motor-MCY [A] (
 x 4,  x 1) 
3.10.15 DEVELOPMENT  MOTOR-MCY 
 
1.  Rear cover (
 Rear Cover) 
2.  PSU bracket (
 PSU) 
3.  Open the controller box. (
 Controller Box). 
4.  Development motor-MCY [A] (
 x 4,  x 1) 
3.10.16 DEVELOPM ENT CLUTCH-K 
 
1.  Rear cover (
 Rear Cover) 
2.  Open the controller box. (
 Controller Box). 
3.  Development clutch-K [A] (
 x 2,  x 1,...

 
B230/B237/D042 3-72 SM 
3.11 FUSING 
3.11.1 FUSING UNIT 
 
ƒ  Turn off the main switch and wait until the fusing unit cools down before beginning 
any of the procedures in this section.  The fusing unit can cause serious burns. 
 
1.  If you will install a lot of new parts in the fusing unit (at PM for example), then set 
SP 3902-014 to 1. 
 
ƒ  If you do this, then the machine will reset the PM counter for the fusing unit 
automatically, after you turn the power on again. 
Do not do this if you...

 
SM 3-73 B230/B237/D042 
Replacement 
Adjustment 
3.11.2 FUSING BELT, PRESSU RE ROLLER, FUSING LAMPS 
 
1. Fusing unit (
 Fusing Unit) 
2.  Fusing upper cover [A] (
 x 4) 
 
3.  Cleaning unit [B] (
 x 2) 
 
4.  Lock lever front and rear [C] (snap ring x 1 each)  

 
B230/B237/D042 3-74 SM 
 
5.  Top frame [D] (
 x 4,  x 1) 
 
6.  Front side stay [E] (
 x 2) 
 
7.  Release the pressure roller lamp cord [F] (
 x 1). 
 
ƒ  The color of the fusing lamp cord differs depending on the destination. 
ƒ  Red: 220 - 240 V,  Blue: 120 V 
8.  Rear side stay [G] (
 x 2)  

 
SM 3-75 B230/B237/D042 
Replacement 
Adjustment 
 
9.  Heating roller fusing lamp front stay [H] (
 x 1) 
10.  Pressure roller lamp front stay [I] (
 x 1) 
 
11.  Heating roller fusing lamp rear stay [J] (
 x 1) 
12.  Pressure roller fusing lamp rear stay [K] (
 x 1) 
 
13.  Heating roller fusing lamp assembly [L] (
 x 4) 
14.  Pressure roller fusing lamp [M] (
 x 1)  

 
B230/B237/D042 3-76 SM 
 
15.  Separation plate [N] (C Ringx 2, spring x 2) 
 
16.  Remove the pressure roller gear [O] (C Ri ng x 1), one-way clutch gear [P] (C Ring 
x 1) and idle gear [Q]. 
 
17.  Pressure roller [R] (bearing x 2)  

 
SM 3-77 B230/B237/D042 
Replacement 
Adjustment 
 
18.  Fusing belt [S] with rollers (bearing x 4, insulating bushing x 2, C Ring x3) 
 
19. Fusing belt [T] 
When reassembling the fusing unit 
When replacing the fusing roller or pressure  roller, you have to apply lubricant to the 
following places. 
Fusing Roller 
 
ƒ  Apply Barrierta S552R to the notch [A] at the front side of the fusing roller.  

 
B230/B237/D042 3-78 SM 
ƒ  Apply Barrierta S552R to the edge [B] of the step at the rear side of the fusing roller. 
 
ƒ  Do not apply lubricant to the area [C] as shown. 
Pressure Roller 
 
ƒ  Apply Barrierta S552R to the front edge [A ] and rear edge [B] of the pressure roller as 
shown above. 
3.11.3 HEATING, FUSING  AND TENSION ROLLER 
 
1.  Fusing belt with rollers (
  Fusing Belt, Pressure Roller, Fusing Lamps) 
2.  Fusing roller [A] 
3.  Tension roller [B] 
4.  Heating roller [C]  

 
SM 3-79 B230/B237/D042 
Replacement 
Adjustment 
3.11.4 LUBRICANT ROLLER  AND CLEANING ROLLER 
 
1.  Cleaning unit (
  Fusing Belt, Pressure Roller, Fusing Lamps) 
2.  Remove the spring [A] and bushing [B] at the front and rear side of the cleaning 
unit. 
 
3.  Lubricant roller [C] 
4.  Cleaning roller [D]  

 
B230/B237/D042 3-80 SM 
3.11.5 FUSING/PAPER EXIT FAN 
 
1.  Open the right door. 
2. Rear cover 
3.  Right rear cover (
  Right Rear Cover) 
4.  High voltage supply board bracket (
  High Voltage Supply Board Bracket) 
5.  Fusing/paper exit fan [A] (
 x 1,   x 1, hook x 2) 
When Reinstalling the Fan 
 
Make sure that the fusing/paper exit fan is in stalled with its decal facing to the right side.