Ricoh B230 Service Manual

 
SM 5-425 B230/B237 
Service 
Tables 
4-Digit Entries for Keys 1 to 10 
 
Key No. Copy Printer Scanner Web 
1 2222 (SCS) 
2 2223 (SRM) 
3 256 (IMH) 
4 1000 (ECS) 
5 1025 (MCS) 
6  4848 (COPY)  4400 (GPS)  5375 (Scan)  5682 (NFA) 
7  2224 (BICU)  4500 (PDL)  5682 (NFA)  6600 (WebDB) 
8  4600 
(GPS-PM) 3000 (NCS)  3300 (PTS) 
9    2000 (NCS)  2000 (NCS)  6666 (WebSys)
10    2224 (BICU)    2000 (NCS) 
 
ƒ  The default settings for Keys 1 to 10 are all zero (“0”). 
Key to Acronyms 
Acronym Meaning Acronym...

 
B230/B237 5-426  SM 
(Document Server) 
The machine is now set to record the debugging information automatically on the HDD (the 
target selected with SP5857-002) for the events that you selected with SP5858 and the 
memory modules selected with SP5859. 
Please keep the following important points in mind when you do this setting: 
ƒ  Note that the number entries for Keys 1 to 5 are the same for the Copy, Printer, 
Scanner, and Web memory modules. 
ƒ  The initial settings are all zero.   
ƒ  These...

 
SM 5-427 B230/B237 
Service 
Tables 
2.  On the control panel, enter “01”. Then hold down   for at least 3 seconds until 
the machine beeps and then release it. This saves the debug log to the hard disk 
for later retrieval with an SD card by the service representatives. 
3.  Switch the machine off and on to resume operation. 
The debug information for the error is saved on the hard disk. This lets the service 
representative retrieve it on their next visit by copying it from the HDD to an SD card....

 
B230/B237 5-428  SM 
SD card. With the file already created on the SD card for the log file, the data only needs to 
be recorded; a new log file does not require creation. To create a new log file, do 
SP5857-012 to delete the debug log data from the SD card. Then do SP5857-017.  

 
SM 5-429 B230/B237 
Service 
Tables 
5.10 DIP SWITCHES 
5.10.1 CONTROLLER BOARD 
 
DIP SW No. OFF ON 
1 Boot-up from Flash 
Memory Boot-up from SD card 
2 to 8 Factory Use Only: Do not change the switch 
settings. 
 
5.10.2 BICU BOARD 
 
DIP SW No. OFF ON 
1 and 2 Factory Use Only: Do not change the switch 
settings. 
  

 
 
 
 
 
 
DETAILED DESCRIPTIONS 
  

 
SM 6-1 B230/B237 
Detailed 
Descriptions 
6. DETAILED SECTION DESCRIPTIONS 
6.1 OVERVIEW 
6.1.1 COMPONENT LAYOUT 
 
 
1. Scanner HP sensor 
2. ADF exposure glass 
3. 2nd scanner (2nd carriage) 
4. Exposure glass 
5. Original width sensor 
6. Scanner lamp 
7. 1st scanner (1st carriage) 
8. Original length sensor 
9. Lens block 14. Paper transfer roller 
15. Registration roller 
16. By-pass feed table 
17. Tray 2 
18. Tray 1 
19. Toner collection bottle 
20. Laser optics housing unit 
21. PCU (4 colors)...

 
B230/B237 6-2  SM 
10. Sensor board unit (SBU) 
11. Scanner motor   
12. Fusing unit 
13. Duplex unit 23. Image transfer belt unit 
24. Toner bottle (4 colors) 
25. ID sensor 
 
6.1.2 PAPER PATH 
This diagram shows the copier with the 1000-sheet booklet finisher. 
 
1. Original tray 
2. Original exit tray 
3. Duplex inverter 
4. Duplex feed 
5. By-pass tray feed 
6. Tray 1 feed 
7. Tray 2 feed 8. Tray 3: Optional paper feed unit/LCT 
9. Tray 4: Optional paper feed unit 
10. Finisher stapler (Optional)...