Ricoh Aficio MP 6000SP User Manual

Initial Settings
131
4
❖Program Memory Lock ID
Program a Memory Lock ID to be entered before printing documents when
the Memory Lock function is activated.
APress [Facsimile Features].
BPress [Initial Settings].
CPress [Program Memory Lock ID].
DEnter an ID using the number keys, and then press [OK].
A Memory Lock ID can be any four-digit number, except 0000.
If you make a mistake, press [Clear] or the {Clear/Stop} key before pressing
[OK], and then try again.
EPress the {User Tools/Counter} key....

Facsimile Features
132
4
❖Program Fax Information
Program information to be shown on the display of the other machine and
printed as a report. The following information can be programmed.
Fax Header
Own Name
Own Fax Number
For details about how to program Fax Information, see “Registering Fax In-
formation”.
❖Enable H.323
Specify whether or not H.323 is used for IP-Fax transmission.
The default setting is Off.
❖Enable SIP
Specify whether or not SIP is used for IP-Fax transmission.
The default setting...

Initial Settings
133
4
❖SIP Settings
Set the SIP servers IPv4 address or host name, and SIP user name.
If you select [On] using the User Parameters, you can use the SIP server. See
“Parameter Settings” ( switch 34, bit 1).
You can use alphanumeric symbols (lower and upper cases) and symbols (“;”,
“?”, “:”, “&”, “=”, “+”, “$”, “,”, “-”, “_”, “.”, “!”, “~”, “*”, “#”, “‘”, “(”, “)”, “%”,
“/”, and “@”) for registration of the SIP User Name in SIP Settings. Make sure
you enter these characters correctly.
Use...

Facsimile Features
134
4
FPress [Change] for “Prefix”.
GEnter the Prefix using the number keys, and then press [OK].
To change the existing prefix, press [Clear], and then enter a new prefix.
For documents sent using a gateway to G3 Fax, prefixes can be used. If
the first several digits of IP-Fax number and the gateway- specific prefix
are identical, documents can be transmitted using the registered digits
of the gateway. For example, if both 03 and 04 have been registered as
gateway number while...

Reception File Setting
135
4 Reception File Setting
Specify whether received documents are to be saved on the hard disk or printed
immediately without being saved. You can print stored documents repeatedly
or download them as images to a computer using a Web Image Monitor or Desk-
TopBinder. If you select printing without saving, documents are printed each
time they are received.
If you have used System Settings to specify to have received faxes distributed to
the delivery server, the documents cannot be...

Facsimile Features
136
4
Note
❒You can use “Parameter Settings” (switch 10, bit 5) to select whether or not
to print stored received documents. See “Parameter Settings”.
❒If [Store] is selected and a destination for notification is specified, notifica-
tion of document reception can be sent to the specified e-mail address.
❒Documents saved on the hard disk are categorized as received and stored
documents.
❒You cannot change to a different setting if received documents have been
stored on the hard disk....

Program / Change / Delete Scan Size
137
4 Program / Change / Delete Scan Size
Program frequently used scan sizes.
Important
❒When programming or changing a scan size, it is recommended that you
make a record of the new size.
When you select a scan size to scan a custom size original, two custom sizes are
available (Program Size 1 and Program Size 2). Use these functions to program
a custom size in advance. The procedure is the same for programming and
changing.
You can program up to two sizes.
Specify a...

Facsimile Features
138
4
EEnter a horizontal size using the number keys.
Each time you press [mm] or [inch], the units switch between “mm” and
“inch”. If you enter a length and press [mm] or [inch], the length is converted
automatically according to the unit (fractions are rounded off). For example,
when you enter {2}, {2}, and {0} in millimeters and change to “inch”, the
length “8.7 inch” is shown on the display. If you press [mm] or [inch] again,
“221 mm” is displayed.
If you make a mistake, press...

Program / Change / Delete Scan Size
139
4
Deleting a scan size
Delete programmed scan size.
APress [Facsimile Features].
BPress [Scan Settings].
CPress [Program / Change / Delete Scan Size].
DPress [Delete], and then select [Program Size 1] or [Program Size 2].
EPress [Delete].
To cancel deleting, press [Do not Delete]. The display returns to that of step 
D.
FPress [Exit].
GPress the {User Tools/Counter} key.
Downloaded From ManualsPrinter.com Manuals 

Facsimile Features
140
4Registering Fax Information
This section describes Fax Information.
You can send information to the other party when transmitting or receiving a fax
document. This information is shown on the display of the other machine and
printed as a report. The following information can be sent.
Important
❒You can confirm programmed settings from the User Parameter List. It is rec-
ommended that you print and keep the User Parameter List when you pro-
gram or change settings. See “Parameter...