Remington SPR 210, SPR 220 Instruction Manual

							11
Instructions For Assembly Of Shotgun  (cont’d)
4. Now that the barrels have been locked into the receiver, you must reattach the fore end to the barrel.  Pull
outward on the mechanical latch in the center of the fore end and place the fore end on the receiver.  With
an upward swinging motion, lock the fore end onto the barrels.  Do not force the fore end into its locked
position on the barrels.  If the latch does not go to its final flat position, it may be necessary to push it
into place.  Never force the latch in the flat position.  (See 
Picture 20).
Loading and Unloading Your Shotgun
WARNING
Never load or fire the shotgun unless the barrels is locked into position on the receiver, and the fore end is locked in to the receiver and barrels.
WARNING
Make sure the shotgun is pointed in a safe direction and the trigger block safety is engaged at all times while loading and unloading.
NEVER allow your fingers or other objects to contact the trigger (s) while loading or unloading.
WARNING
Do not disengage the trigger block safety until you are ready to fire and have the gun pointed safely downrange
WARNING: DO NOT LOAD SHOTGUN UNTIL YOU ARE READY TO FIRE.
Picture 20
Picture 17Picture 18Picture 19 
						

							Loading and Unloading Your Shotgun  (cont’d)
TO LOAD:
1. Make sure the ammunition that you are using is the correct size and gauge.  The barrels are marked with
the gauge and chamber size.  Barrels marked 3” (76mm) will use only 2 3/4” (70mm) or 3”(76mm) shot
shells and must not be used with 3 1/2” (89mm) shells.  Barrels marked with 2 3/4” (70mm) will use only
2 3/4”  (70mm) and must not be used with or 3” (76mm) or 3 1/2” (89mm) shells.
2. Visually inspect the chambers and barrels for obstructions by breaking open the shotgun by depressing
the locking lever and tipping the barrels down.  The chambers and barrels should be free of oil or grease
or obstructions.  (See 
Picture 21).
3.After inspection, load the correct type of shot shells into the chambers making sure that the shells are
flush with the extractor (See 
Pictures 22and 23), then close the action by swinging the barrels up until
they lock into the receiver and the top lever moves back to the center position.  If the top lever does not
move to the center, (See 
Picture 24) break open the action again and check to see if the shot shells are
fully seated in the chambers.  If the shells are fully seated then reclose the action. If the shot shells are
not fully seated, check the chamber for blockage and check the shells for deformation and retry closing
the action once more.  If the shells are the correct type and the chambers are not blocked and the shells
are not deformed and the top lever does not move at least three quarters of the full travel distance to the
center after closing, then unload the gun (follow Unloading Instructions) and have a competent gunsmith
look at the gun or return the gun to Remington I.S.P. (See address in Parts & Service Section) for
inspection.  Note: The top lever may not move completely to the center on a new shotgun until the gun is
broken in.  The lever must move at least three quarters of the full travel distance.  Try and move the top
lever to the center position by pushing it, do not force it.
12
Picture 22Picture 23
Picture 21
Picture 24 
						

							Loading and Unloading Your Shotgun  (cont’d)
TO UNLOAD:
1. Break open the shotgun by use of the top lever, and tip the barrels down.  (See Picture 25).
2. Remove the shell(s) from the chamber(s) by grabbing them by the rim of the shell(s) and pulling them
from the chambers and store them in a safe place.  (See 
Picture 26).
3. Visually check the barrels to make sure that they are free from obstructions.  (See 
Picture 27).
Firing Your Shotgun
WARNING: NEVER LOAD A CARTRIDGE INTO THE CHAMBER UNTIL YOU ARE READY TO FIRE THE SHOTGUN.
WARNING
Do not disengage the trigger block safety until the shotgun is pointed in a safe direction and you are ready to fire.
WARNING
If a cartridge does not fire and the trigger has been pulled and the trigger block safety is disengaged…Stop! And do the following: a) Make sure
the gun is pointed in a safe direction b) Engage the trigger block safety c) Wait 60 seconds d) Follow the instructions above for unloading the
shotgun.
If during firing the sound of any cartridge is noticeably softer or louder than the previous cartridge fired, Stop! Do not load another cartridge or
fire another cartridge and do the following: a)  Make sure the gun is pointed in a safe direction b) Engage the trigger block safety c) Follow the
instructions above for unloading the shotgun d) With the shotgun unloaded visually inspect the shotgun for barrel blockage or damage.
Then  inspect the mechanical operation and receiver of the shotgun for damage before continuing.
READ, UNDERSTAND AND FOLLOW ALL WARNINGS AND INSTRUCTIONS IN THIS MANUAL
BEFORE FIRING THE SHOTGUN.
13
Picture 25Picture 26
Picture 27 
						

							15
14
Firing Your Shotgun  (cont’d)
TO FIRE THE SHOTGUN:
1. Make sure the shotgun is pointed in a safe direction with the trigger block safety engaged.
(See 
Picture 28).
2. Make sure you are wearing eye and ear protection.
3. Keep your fingers away from the trigger(s).
4. Push the trigger block safety to the “off” or “fire” position with the red dot showing.  (See 
Picture 29).
5.With the butt stock held firmly against your shoulder and the barrels pointed towards your intended
target, place your trigger finger on the trigger.  The shotgun will fire when you pull or squeeze the trigger
with the requisite force.  (See 
Picture 30).
6.If you are using a Model 210 shotgun and intend to fire a second shot, release the trigger and then pull
it a second time.  The second round will then fire.  If you are using a Model 220 shotgun, move your
finger to the other trigger and pull it.  The second round will now fire.
Picture 28
Picture 30
Picture 29 
						

							Firing Your Shotgun  (cont’d)
WARNING
Once you have fired the shotgun, immediately push the trigger block safety to the “on” or “safe” position.  Then follow the unloading
instructions above while keeping the muzzle pointed in a safe direction.
Instructions For Disassembly Of The Shotgun
1. Make sure the shotgun is unloaded (FOLLOW UNLOADING INSTRUCTIONS)  and pointed in a safe
direction.
2. Make sure the trigger block safety is engaged in the “on” or “safe” position.  (See 
Picture 34).
3. Remove the fore end from the barrel by pulling out the mechanical lever in the lower center of the fore end
and removing the fore end in a downward outward swinging motion.  (See 
Picture 32).  Never force the
fore end off the barrel and receiver.
4.With the barrel and receiver supported with one hand, push the top lever fully to the right and tip the
barrels down until they disengage from the receiver.  Check the barrels for damage and obstructions after
removal.  (See 
Picture 33).
15
Picture 31
Picture 32Picture 33 
						

							16
Manufacturer’s Warning
This firearm was manufactured to properly perform with the original parts as designed.  It is your duty to make
sure any parts you buy are correctly installed and that neither replacements nor originals are altered or changed.
Your shotgun has many parts that must relate correctly to other parts for safe and accurate operation.  Putting a
gun together wrong or with modified parts can result in a damaged gun, or personal injury or death to you or
others. Always let a qualified gunsmith work on your gun or at least, check any work not performed
by a gunsmith. Firearms safety is your primary concern. 
THE GUN OWNER MUST ACCEPT FULL
RESPONSIBILITY FOR THE CORRECT REASSEMBLY AND FUNCTIONING OF THE FIREARM AFTER
ANY DISASSEMBLY OR REPLACEMENT OF PARTS.
To Clean and Maintain Your Shotgun
A. Follow procedures for unloading shotgun as described previously.
B. Follow procedures for disassembly of shotgun as described previously.
C. Materials needed to clean this shotgun are: a cleaning rod, cotton bore patches, brass bore brush,
powder solvent (such as Remington BriteBore
™), a small soft brush and good quality gun oil
(such as Rem®Oil).
WARNING
Lead or lead compounds are known to the State of California to cause cancer, birth defects, reproductive toxicity, and other serious physical
injury. Those who clean firearms should take protective measures to avoid contact or exposure to such chemicals.
D. Using the bore brush with powder solvent, scrub the interior of the barrel and chamber to remove any
powder and lead residue in the bore. Always and lastly, swab the interior of the barrel with a cotton patch
with gun oil to coat and protect the bore and chambers from rust and corrosion.
E.Any powder fouling on the firing wall, barrel, etc. can be easily cleaned with a brush and powder solvent.
F. All external surfaces should be wiped down with a light coat of rust preventative. Avoid using too much
oil as powder, dust or other foreign material may get trapped in the oil. This could lead to congealed
deposits which may interfere with the safe and reliable operation of this shotgun.
G.
USE CAUTIONwhile using solvents in gun bore cleaning. Prolonged or excess contact with
solvents can damage the gun’s bluing and finish. Be sure to wipe away all excess solvent and then 
lubricate with oil.
H.A gun should be cleaned after firing. In addition, external parts should be wiped with an oiled cloth
after handling. A light oil is ordinarily all that is necessary in cleaning if the gun has not been fired or fired
very little. If a gun is used frequently, it must be cleaned after each firing and regularly serviced by a
professional gunsmith. If the gun has been stored, remove all excess oil and/or grease before firing.
Always check to be sure that no cleaning patch or other obstruction remains in the bore or chambers
before firing. 
						

							17
DANGER – Ammunition Warning
Firearms may be damaged and serious personal injury or death to the shooter or bystanders may result from any
condition which contributes to the generation of excessive pressure or uncontrolled release of gas within the
firearm. Such adverse conditions can be caused by bore or chamber obstructions, propellant powder overloads or
by defective, incorrect or improperly loaded and assembled cartridge components. Even the strongest firearm can
be blown up as a result of excessive pressure. It is extremely dangerous to use a cartridge whose pressure is
greater than that developed by cartridges loaded to industry standards.
Ammunition (Cartridges) Notice
We specifically disclaim responsibility for any damage, injury or death occurring in connection with or as the
result of the use of the shotgun with faulty, nonstandard, remanufactured, hand loaded or reloaded ammunition
or with cartridges other than factory cartridges for which the shotgun was originally chambered.
Lubrication Warning
Firing a shotgun with oil, grease or any other material even partially obstructing the bore may result in damage to
the shotgun and personal injury to the shooter and those nearby.  Do not spray or apply lubricants directly on
ammunition. If the powder charge of a cartridge is affected by the lubricant, they may not fully ignite yet the ener
gy from the primer and/or powder may still be sufficient to push the projectile or wad into the bore where it may
become lodged. Firing a subsequent cartridge into the obstructed bore will damage the shotgun and may cause
personal injury to the shooter and those nearby.  Use lubricants properly.  You are responsible for the proper care
and maintenance of your firearm and ammunition.
PARTS AND SERVICE
To Order Parts
ALL PARTS ARE SUBJECT TO A $10.00 CHARGE FOR SHIPPING AND HANDLING. Some parts are restricted and
may only be installed by returning the shotgun to us.  When ordering parts, please state the Model, Gauge, Serial
Number, and Finish Color. For parts information, call (321) 6391432.
Service
To obtain information about returning your shotgun for service or repairs, call (321) 6391432.
One Year Limited Warranty
This shotgun is warranted to the original retail customer for one year from the date of retail purchase against
defects in material and workmanship. All parts and labor or replacement at our option are covered. The wood stock
is not covered by the one year warranty. The warranty on the wood stock is 60 days and is limited to the original
retail customer and extends 60 days from the date of retail purchase and covers only manufactured and material
defects. 
						

							19
PARTS AND SERVICE  (cont’d)
One Year Limited Warranty
Transportation to and from our repair facilities, government fees, damage caused by failure to perform normal
maintenance, sales outside the United States, damage caused by use of high velocity, high pressure, reloaded or
other nonstandard ammunition, or by any unauthorized repair, modification, misuse, abuse or alteration of the
shotgun is not covered by this Limited Warranty.
Implied Warranty
ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANT ABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL
RETAIL PURCHASE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
To the extent any provision of this warranty is prohibited by federal, state, or municipal law, which cannot be pre
empted, it shall not be applicable. This warranty gives you specific legal rights, and you may also have other rights
which may vary from state to state.
To obtain warranty service, send your shotgun with proof of retail purchase, freight prepaid to:
REMINGTON I.S.P.
c/o USSG
402 Richard Road
Rockledge, FL  32955
NOTICE: It is illegal to ship a firearm with ammunition in the firearm or in the same packaging. Firearms and
ammunition must be shipped separately. For information about shipping ammunition, call (321) 6391432.
Your Owner’s Manual
Always keep this manual with your firearm. Make sure you understand all the warnings, operation instructions and
safety procedures. When you lend, give or sell the firearm, be sure this manual goes with it. You can get a copy
of this manual from Remington upon request.
18 
						

							PARTS LIST
Model 210/220 Exploded View
1.barrel assembly 29.cam pin 55.safety
2.extractor spring 30.sear pin 56.sear lifter lever
3.plunger31.left sear57.sear lifter
4.right extractor 32.left hammer assembly 58.sear lifter spring
5.left extractor 33.plug 59.sear lifter level pin
6.screw 34.plug screw 60.pin
7.pin35.follower61.screw
8.sling swivel ring 36.left rod assembly 62.trigger plate
9.screw 37.right rod assembly 63.screw
10.barrel sling swivel base 38.cocking lever 64.trigger guard
11.front sight39.cocking lever pin65.trigger guard screw
12forend 40.screw 66.right trigger
13.washer 41.locking lever 67.trigger spring
14.spring 42.right hammer assembly 68.left trigger
15.latch body43.hammer pin69.pin
16.forend latch 44.right sear 70.stock
17.pin 45.pin for safety and 71.screw
18.screw thumb piece 72.washer
19.screw 46.thumb piece 73.butt plate
20.screw 47.locking bolt 74.woodscrew
21.lever pin 48.connecting rod 75.woodscrew
22.left lever49.locking bolt spring 76.stock sling swivel base
23.right lever 50.cam stop 77.sear spring
24.hinge 51.threaded connecting 78.wright
25.lever spring piece 79.pin
26.screw 52.locking bolt lever 80.safety spring
27.receiver 53.ball 81.bushing
28.cam54.sear lifter lever spring
19 
						

							21
Model 210 with Single Trigger 
Model 100
1. left sear
2. right sear
3. trigger
4. spring
5. selector plunger
6. selector
7. pin
8. weight
9. arm base spring
10. selector arm base
11. selector arm spring
12. selector arm pin
13. selector arm
Firing mechanism of Model 220 shotgun 3inch
chamber version GA. 12, .410
Model 220
1. barrel assembly
2. receiver
3. firing pin
4. firing pin spring
5. firing pin bushing
6. left hammer
7. right hammer
8. firing pin buffer
20