RCA 60 Manual

1

Date
CID sequence number
Line number
Time
CID phone number
CID name
Dialing a Stored Number 
Make sure the phone is ON (in TALK mode).
1.  Press the DIR/3button.
2. Use the VOL ( 6 or 5) button to scroll to the desired telephone number.
3. Press Select/Save to dial the displayed number.
         -OR-
1. Make sure the phone is OFF	(not in TALK mode).
2. Press the DIR/3 button.
3. Use the VOL ( 6 or 5) button to scroll to the desired telephone number.
4. Press the Talk button to access an...



Receiving and Storing CID Records
When you receive a call, Caller ID information is transmitted by the phone company to your telephone between the first and second ring. The Caller ID information appears on your phone’s display while the phone rings, giving you a chance to monitor the information and decide whether or not to answer.
If you are not at home or cannot answer, the telephone stores the information so that you can see who called while you were unavailable. Caller ID memory...



Transferring CID Records to Memory
You may transfer a Caller ID record to your phone’s memory.
NOTE: It is important that you format CID records correctly before storing in memory. It is not possible to reformat CID records stored in memory.
1. Use the CID/4button to scroll to the desired record.
2. Press the Conf/Store button.
3. If the CID shows NO NAME, then please enter the name for this record.
Dialing a Caller ID Number
When reviewing any call record in the Caller ID memory, you can...

4

Deleting the Current Caller ID Record
To delete only the record in the display:
1. Use the CID/4 button and then VOL ( 6 or 5) button to display the desired Caller ID record.
2. Press Delete/Mute. 
Deleting All Caller ID RecordsTo delete all the Caller ID records in memory:
1. Use the CID/4 button and then VOL ( 6 or 5) button to display any Caller ID record.2. Press and hold Delete/Mute. The display asks DELETE ALL? for several seconds.3. Press Delete/Mute again, within five seconds, to erase...

5

Changing the Battery
CAUTION: To reduce the risk of fire or personal injury, use only the Thomson Inc. approved Nickel-metal Hydride (Ni-MH) battery model 5-2734, that is compat\
ible with this unit.
1. Make sure handset is OFF (not in TALK mode) before you replace battery.
2. Remove the battery compartment door.
3. Disconnect the battery plug from the jack inside the battery compartment and remove the battery pack from the handset.
4. Insert the new battery pack and connect the cord to the jack...



Belt Clip Operation
Connecting the Belt Clip
There are two slots, one on each side of the handset.
• Attach the belt clip by inserting the sides of the belt clip into the sl\
ots. Snap the ends of the belt clip into place.
Display Messages
The following indicators show the status of a message or of the unit.
LINE	ON	HOLD:		 		The line you selected is currently on hold.
LINE	IN	USE:				The line you selected is currently use by another     extension.
SEARCHING..:						 		Handset is out of...



Troubleshooting Guide
Telephone Solutions
No	dial	tone
• Check and repeat installation steps:
 Ensure the base power cord is connected to a working outlet.
 Ensure the telephone line cord is connected to the base and the wall jack .
• Connect another phone to the same jack; if there is still no dial tone, the problem might be your wiring or local service.
• The cordless handset may be out of range of the base. Move closer to the base.
• Ensure the battery is properly charged (14 hours).
•...



Unit	locks	up	and	no	communication	between	the	base	and	cordless	handset
• Unplug the AC power adaptor from the wall outlet and the back of the base, and remove the backup batteries from the bottom of base (if previously installed). Remove the handset battery. Wait for 30 seconds and plug the power adaptor back into the base and wall out, and re-install batteries in the base unit. Reconnect the handset battery and charge for 14 hours.
Caller ID Solutions
No	Display
• Is battery fully...



• Retain the original packaging in case you need to ship the phone at a la\
ter date.
• Periodically clean the charge contacts on the handset and charge cradle with a clean pencil eraser.
Causes of Poor Reception
• Aluminum siding.
• Foil backing on insulation.
• Heating ducts and other metal construction that can shield radio signals.
• You’re too close to appliances such as microwaves, stoves, computers, etc.
• Atmospheric conditions, such as strong storms.
• Base is installed in the...

0

Limited Warranty
What your warranty covers:
• Defects in materials or workmanship.
For how long after your purchase:
• One year, from date of purchase. (The warranty period for rental units begins with the first rental or 45 days from date of shipment to the rental firm, whichever comes first.)
What we will do:
• Provide you with a new or, at our option, a refurbished unit. The exchange unit is under warranty for the remainder of the original product’s warranty period.
How you get service:
•...