RadioShack Pro 96 Truking Scanner Owners Manual

111
1240–1300 MHz ................................................................ 0.7µV
AM:
25–54 MHz ........................................................................... 1µV
108–136.9875 MHz .............................................................. 1µV
137–174 MHz .................................................................... 1.5µV
216–225 MHz .................................................................... 1.5µV
406–512 MHz...

112
Audio Output Power (10% THD) .....................................170 mW
Built-in Speaker ........ 1
3/8Inches (36 mm) 8-ohm Dynamic Type
Power Requirements:
Batteries .............................................. 4 AA Alkaline Batteries or
...................................................... 4 AA Rechargeable Batteries
External Power .................................................... 9 V/300 mA DC
Current Drain (Squelched) ................................................ 90 mA
Battery Charge...

113
COMMAND QUICK REFERENCE GUIDE
Scan Mode
KeystrokesFunction
SCAN Activates Scan Mode, resumes scan when
stopped on a channel or talkgroup.
MANIf scanning or monitoring a trunked call, stops
scan operation, activates Manual Mode.
If monitoring conventional call, stops scan
operation, activates Manual Mode, holds on
active channel.
PGM If scanning or monitoring a trunked call, stops
scan operation, activates Program Mode.
If monitoring conventional call, stops scan
operation, activates Program Mode,...

114
Manual Mode
ENTERWhen monitoring a conventional channel that
is programmed for CT or DC Search Mode,
stores a detected CT or DC code with the
channel memory.
SorTChanges scan direction, up or down.
FUNC + MANToggles digital AGC
FUNC +
TRUNKWhen monitoring a talkgroup call, toggles
display of control channel text tag or Trunked
ID sub-bank status.
FUNC + PRIIf monitoring a conventional channel, stores
the frequency into the priority channel.
FUNC +
TUNEIf monitoring a conventional channel, stores
the...

115
Program Mode
ENTER
When monitoring a conventional channel
that is programmed for CT or DC Search
Mode, stores a detected CT or DC code
with the channel memory.
SorTSsteps to the next channel,Tsteps to the
previous channel. Hold down to scroll.
FUNC + MANToggles digital AGC.
FUNC + TRUNK Enters trunked ID list for current bank.
FUNC + PRIStores the frequency of the selected
channel into the priority channel.
FUNC + TUNEStores the frequency of the selected
channel frequency into the tune memory.
FUNC +...

116
SRCHSets search range for programmable
search range (PSR).
2, 3, PGM Jumps to channel 23 in the current bank.
1, 2, 3, PGMJumps to bank 1, channel 23.
DECIMAL POINTToggles delay on selected channel on or
off.

ENTEREnters a frequency into channel memory.
SorTSsteps to the next channel,Tsteps to
the previous channel, hold down to scroll.
FUNC + MANToggles digital AGC.
FUNC + MODEIf selected channel mode is set to CT or
DC, edits CT or DC code.
FUNC + PRIStores the frequency of the selected
channel...

117
Search Mode
KeystrokesFunction
SCAN Activates Scan Mode.
MANActivates Manual Mode.
PGM Activates Program Mode.
WXActivates Weather Mode.
PRI Toggles priority.
TUNEEnters Tune Mode.
AT TToggles attenuation for active search range,
or, if global attenuation is set, toggles global
attenuation on or off.
L/OUTLocks out undesired search frequencies or
search channels.
PAUSE Pauses and resumes search operations.
MODECycles through AM/FM/CT/DC modes for
selected search range.
SRCH Steps through the...

118
Weather Mode
FUNC + PGMWhen searching SR3, SR4, SR5 and SR6,
stores active search frequency in desired
bank and channel (e.g., “123 + ENTER”
stores the active frequency in Bank 1,
Channel 23).
FUNC +
ENTER
When searching SR3, SR4, SR5 and SR6,
stores active search frequency in next
available channel in desired bank (e.g., “1 +
ENTER” stores active frequency in next
empty channel in Bank 1).
FUNC+7 TogglesSeekonoroff.
FUNC + 0Toggles Zeromatic on or off.
KeystrokesFunction
SCAN Activates Scan Mode....

119
Tune Mode
ID List Edit
KeystrokesFunction
SCAN Activates Scan Mode.
MANActivates Manual Mode.
PGM Activates Program Mode.
WXActivates Weather Mode.
PRI Toggles priority.
AT T
Toggles attenuation for active search
range, or, if global attenuation is set,
toggles global attenuation on or off.
PAUSE Pauses and resumes tune operations.
MODECycles through AM/FM/CT/DC modes.
SRCH Activates Search Mode
DECIMAL POINTToggle tune delay on or off.
SorTChanges tune direction, resumes tune
operation after...

120
TRUNKSteps to first ID in next ID sub bank.
TUNE Enters Tune Mode.
L/OUTToggles lockout on the selected ID.
MODECycles trunking mode through MO, ED
and “not trunked”.
SRCHActivates Search Mode.
 ENTER Stores ID into selected location.
SorTSsteps to the next ID,Tsteps to the
previous ID, hold down to scroll.
FUNC + MAN Toggles digital AGC.
FUNC +
DECIMAL POINTSelects ID delay duration for selected
bank.
FUNC CLRClears all programming data in selected
ID.
FUNC + 1Toggles active sub bank on or off.
FUNC...