Projector Christie Roadster Hd14k M User Manual

							M Series User Manual2-1020-100009-07 Rev. 1 (07-2012)
2 Installation and Setup
This section explains how to install, connect and optimize the projector for delivery of superior image quality. 
Illustrations are graphical representations only and are provided to enhance the understanding of the written 
material. 
2.1 Projector Quick Setup and Installation
The following instructions are for those preferring a quick setup. Refer to the remaining subsections for 
detailed setup instructions.
 
Always power down the projector and disconnect all power sources before
servicing or cleaning.
See the Safety Warnings and Guidelines in Section 5 Maintenance.
2.1.1 Install a Projection Lens
The projection lens, shipped separately from the projector, must be installed prior to setting up the projector. 
Remove the lens plug from the lens opening in the projector before installing
the lens. Retain the lens plug for projector transportation to protect the
optical components from dust and debris.
IMPORTANT! The lens seals the projector, preventing contaminants from entering the interior of the 
projector. Never operate a projector without a lens. Remove the rear lens cap from the lens. 
Keep the front lens cap on the lens to protect it during installation.
1. Rotate the lens clamp to the OPEN position, as shown. 
						

							2-2M Series User Manual020-100009-07 Rev. 1 (07-2012)
Section 2: Installation and Setup
2. Align the lens interface plate with the lens mount. Align the lens electrical connector with the mating 
connector on the lens mount. Fully insert the assembly straight into the lens mount opening without 
turning. Press using your hand as shown. 
NOTE: When installing the lens, ensure that the lens is not inserted at an angle, as this can cause damage.
3. While holding the lens flat against the lens mount, rotate the lens clamp clockwise to lock the lens 
assembly in place.
4. Remove the front lens cap.
5. For added stability such as motion applications, fasten the security screws provided with the lens-mount. 
NOTE: There are two types of lens plate models.
6. Use a 5mm hex driver to fasten the red security screws provided with the lens mount, or hand tighten the 
lens retaining screws attached to the lens. 
NOTES: 1) Recommended for heaviest lenses such as 0.73:1 and 1.2:1.
Use of the lens red security screws or the lens retaining screws is required if
the projector is hoisted or installed in an overhead position. 
						

							Section 2: Installation and Setup
M Series User Manual2-3020-100009-07 Rev. 1 (07-2012)
2.1.2 Position the Projector
2 people are required to safely lift and install the projector.
Place the projector on a sturdy, level surface and position it so that it is perpendicular to the screen at a suitable 
distance. The further back the projector is positioned for the screen, the larger the image will be.
To level the projector adjust its 3 feet. With the projector positioned perpendicular to the screen the image will 
appear rectangular instead of keystoned.
For more detailed instructions to position the projector, see 2.3 Projector Position.
2.1.3 Connect a Source
The input panel where all source connections are made, is located at the back of the projector. Each input is 
clearly labeled for easy identification. Depending on the type of option card installed, connect your source 
using the appropriate cable(s), as follows:
•Analog Input Card: Connect 3-, 4-, or 5-wire RGB source to Red/Pr, Green/Y, Blue/Pb, H/C and V using 3, 
4 or 5 BNC connectors as required.
•Dual 3G/HD/SD-SDI Input Card: Connect the SDI (Serial Digital Interface) cable to one of the two inputs, 
1-IN or 2-IN. Both standard-definition (SD) and high-definition (HD) signals are accepted and automatically 
recognized on either input.
•Dual Link DVI Input Card: Connect a single or dual DVI video signal to the DVI-I connector, an analog 
video signal to the DVI-I connector or an analog video signal to the VGA connector. The DVI signal may 
contain HDCP (High-Bandwidth Digital Content Protection).
•Twin HDMI Input Card: Connect HDMI (High-Definition Multimedia Interface) cable to one of the two 
inputs, 1-IN or 2-IN.
•Video Decoder Input Card: Depending on the source you can apply the following;
• Composite video source to 1-CVBS, using a BNC Cable 
NOTE: Same signal can be used on 4, 5 or 6 when input is selected as CVBS.
• A component signal on Inputs 4(Pr), 5(Y), 6(Pb) using BNC Connectors. 
NOTE: Grouped as a component input, YPbPr.
• S-Video to one of the two, 2-SVID or 3-SVID using S-Video cable.
• S-Video using two BNC cables, with Luma (Y) connected to 4 (Sy) and Chroma (C) connected to 6 (Sc). 
NOTE: Must be grouped as 1 S-Video + 1 CVBS.
•DMX512 Interface Card: Has two 5pin XLR connectors - 1 (input) male and 1 (output) female. If there is 
active communications on the DMX512 Interface card the power LED will blink between low intensity and 
high intensity. 
See 2.11 Connect Sources for more details. 
						

							2-4M Series User Manual020-100009-07 Rev. 1 (07-2012)
Section 2: Installation and Setup
2.1.4 Connect the Line Cord
IMPORTANT!Use the line cord provided with the projector, or ensure you are using a line cord, power plug 
and socket that meet the appropriate rating standards. Voltage and current requirements are 
listed on the license label, located at the back of the projector.
Connect the projector line cord to the AC receptacle at the AC inlet of the projector, then push the wire clip 
over the plug to retain it. This prevents the line cord from inadvertent disconnection. Plug the 3-pronged plug 
end into a suitably rated grounded AC receptacle. Switch the projector ON. The switch is located just above the 
AC receptacle.
NOTE: This product can be connected to an IT power distribution system.
  Do not attempt operation if the AC supply and cord is not within the specified
ratings. On power down, wait 5-10 minutes for the fans to turn OFF before
unplugging the projector. Always switch off the projector before unplugging
the AC line cord.
2.1.5 Power up
After the AC Power has been switched on, the LCD display above the keypad indicates “Please wait” and the 4 
LED status indicators on the top cover window switch on to amber. These indicate that the projector is 
changing its state from powered down to standby. The message “Standby Mode” appears in the display when 
the projector has completed its initialization and is ready for power up. The 2 lamp status LEDs will go off to 
indicate that the lamps are off. The Power status LED will show amber, indicating that the projector is in 
standby mode. The shutter LED will display amber, indicating the shutter is closed. Press and hold the power 
button on the keypad or remote for 2 seconds, or press twice quickly. The lamps will power on and the fans will 
come on. See Section 3 Operation for a full description of the status indicators.
NOTE: The default settings for the projector are to perform a lens calibration after the insertion of a new lens. 
If this is the first time the projector has been powered up with the lens, expect a short period (about 15 seconds) 
where the lens will move slightly.
2.1.6 Select a Source
Press one of the input keys on the remote, or on the built-in keypad to select and display the image for the 
connected source.
2.1.7 Adjust the Image
Adjust the image settings, such as Brightness, Contrast, Gamma, Focus, Zoom etc. using the direct keys on the 
remote, or on the built-in keypad. See Section 3 Operation for more details.
2.2 Detailed Setup and Installation
  Always power down the projector and disconnect all power sources before
servicing or cleaning. 
  See the Safety Warnings and Guidelines in 1.4 Safety Warnings and Guidelines. 
						

							Section 2: Installation and Setup
M Series User Manual2-5020-100009-07 Rev. 1 (07-2012)
2.2.1 About the Projector
Built-In Keypad
The built-in keypad is located on the side of the projector. Use it similarly to the IR remote to control the 
projector. An LCD display is located above the keypad for displaying projector status.
AC Receptacle
The AC receptacle is located above the AC receptacle at the back of the projector. Use this receptacle to plug 
in an appropriately rated line cord. 
Adjustable Feet
Located on the underside of the projector are three adjustable feet. Raise or lower these feet when positioning 
the projector to ensure it is level on all sides so the displayed image will appear rectangular without any 
keystone. See 2.5.1 Adjust Height for instructions on how to adjust the projector feet. 
Input Panel
All source connections are made to the input panel located at the back of the projector. Any of the available 
optional input cards can be installed in the 4 option card slots. The slots are labelled 1 through 4. All option 
cards have LEDs to indicate their status.
Cooling and Air Vents
There are numerous air vents located around the projector. It is important these vents remain unobstructed. 
Adequate airflow through the projector will prevent it from overheating.
Kensington Lock Attachment
Located at the rear of the projector to the left of the AC receptacle, is a Kensington lock attachment point. This 
provides the ability to secure the projector against possible theft. 
						

							2-6M Series User Manual020-100009-07 Rev. 1 (07-2012)
Section 2: Installation and Setup
Lamp Door
The lamp doors are located at the side of the projector, which provides easy access to the lamp module for 
replacement. The lamp doors are fitted with safety interlocks which switch the lamp off when the door is 
opened. The lamp doors are provided with clear windows to indicate when the lamps are on.
Front and Rear IR Sensors
The two IR sensors receive transmissions from the IR remote from up to 100 feet away. It is important to keep 
the transmission path to these sensors unobstructed for uninterrupted communications with the projector. The 
rear IR sensor is located at the back of the projector between the status LEDs. The front IR sensor is located 
next to the front nameplate.
Projection Lenses, Lens Mount and Other Features
The projector includes a motorized lens mount that allows automated lens control and adjustment: vertical and 
horizontal offsets, zoom and focus. 
•Zoom and Focus: There are two internal lens motors that allow for quick motorized adjustment of zoom and 
focus. Adjust zoom to fit the displayed image on the screen and adjust focus to improve the clarity of the 
image.
NOTES: 1) The projection lens is shipped separately from the projector. 2) Use the lens cap when 
transporting the lens to avoid scratching and damaging the lens, which could affect your displayed image. 3) 
Motorized lenses should not be adjusted by hand without first setting them for manual operation, otherwise 
the zoom and focus motors may be damaged. 
(Set in Menu > Configuration > Lens Settings > Manual Zoom/Focus).
•Lens Offset: The motorized lens mount allows vertical and horizontal offset of the displayed image. 
•Shutter: Allows the screen to become absolute black, when in the “closed” state.
•Dynamic Iris Contrast Aperture: Enables adjustment of light output and contrast ratio.
NOTE: Dynamic Iris is only applicable on 200W and 350W models. 
						

							Section 2: Installation and Setup
M Series User Manual2-7020-100009-07 Rev. 1 (07-2012)
2.2.2 Installation Considerations
Proper installation of the projector will ensure the quality of the display. Whether installing a projector 
temporarily or permanently, take the following into account to make sure the projector performs optimally. 
Choose the installation type that best suits your needs: front or rear screen, floor mount or inverted mount.
Front Screen / Floor Mount Installations
Front Screen / Inverted Mount (ceiling) Installation
Rear Screen / Floor Mount Installation
Rear Screen / Inverted Mount (ceiling) Installation
Rear Screen / Floor Mount with Mirror
2.2.3 Front Screen Installations
In front screen installations, the projector and audience are positioned in front of the screen, which can be flat 
or curved.
Flat screens offer a gain of about 1.0 with a viewing angle just less than 180 degrees. This type of screen 
reflects incident light equally in all directions so the audience can see the display from various angles.
ADVANTAGESCONSIDERATIONS
Easy to set up.
Can be moved or changed quickly.
Easy to access.Shares floor space with audience.
ADVANTAGESCONSIDERATIONS
Does not take up audience space.
Projector is unobtrusive.
Projector cannot be accidentally moved.Installation is more permanent.
It is more difficult to access the projector.
ADVANTAGESCONSIDERATIONS
Projector is completely hidden.
Projector is easily accessed.
Usually good ambient light rejection.Requires separate room or enclosure.
Installation cost is usually higher.
ADVANTAGESCONSIDERATIONS
Projector is completely hidden.
Usually good ambient light rejection.Requires separate room.
Installation cost is usually higher.
More difficult to access projector.
ADVANTAGESCONSIDERATIONS
Projector is completely hidden
Usually good ambient light rejection.
Requires less space behind screen than other 
rear screen installations.Requires separate room or enclosure.
Installation cost is usually higher.
More involved to perform setup. 
						

							2-8M Series User Manual020-100009-07 Rev. 1 (07-2012)
Section 2: Installation and Setup
Curved screens have a gain greater than 1.0 with a viewing angle much less than 180 degrees. This type of 
screen does not reflect incident light equally in all directions; instead it is concentrated in a viewing cone. The 
audience sitting within the viewing cone area will see a brighter image than those sitting just outside the area.
2.2.4 Rear Screen Installations
There are two basic types of rear screens: 
•Diffused: A diffused screen has a surface which spreads the light that strikes it. Purely diffused screens have 
a gain of less than 1.0. The advantage of the diffused screen is its wide viewing angle, similar to that of a flat 
screen for front screen projection. This type of screen is suitable when a wide viewing angle is required but 
there is low ambient room lightening.
•Optical: Optical screens take light from the projector and redirects it to increase the light intensity at the 
front of the screen and reduce it in other areas. A viewing cone, similar to that of a curved front screen 
installation is created. This type of screen is better suited for brightly lit rooms where the audience is situated 
within the viewing cone.
2.2.5 Screen Size
Choose a screen size appropriate for your lens and application. If the projector will be used to display text 
information, the image size must allow the audience to recognize all text clearly. The eye sees a letter clearly if 
eye-to-text distance is less than 150 times the height of the letter. Small text located too far from the eye will be 
illegible at a distance no matter how sharply and clearly it is displayed.
To fill a screen with an image, the aspect ratio of the screen should be equal to the aspect ratio of the image 
(expressed as the ratio of its width to its height). Standard video from a VCR has a 4:3 or 1.33:1 aspect ratio. 
For example, to display a VCR output with a 4:3 aspect ratio onto a 10-foot (3m) high screen, the width of the 
screen must be at least 13.3 feet (4m).
2.2.6 Ambient Lighting
The high brightness of this projector is well suited for locations where ambient lighting might be considered 
less than ideal. A typical room with ceiling lights and windows rarely requires special attention. Contrast ratio 
in your images will be reduced if stray light directly strikes the screen. For example, when a shaft of light from 
a window or floodlight falls on the image. Images may appear washed out and less vibrant. Avoid or eliminate 
stray light sources directed at the screen.
2.2.7 Ventilation
The projector vents and louvers provide ventilation, both for intake and exhaust. Never block or cover these 
openings. Do not install the projector near a radiator or heat register, or within an enclosure. To ensure  
						

							Section 2: Installation and Setup
M Series User Manual2-9020-100009-07 Rev. 1 (07-2012)
adequate airflow around the projector, allow free air exchange to the projector with a minimum clearance of 
25cm (10-inch) on the left, right and rear sides of the projector from any walls or other obstructions. Never 
obstruct the air exchange to the projector.
2.2.8 Other Considerations
Other considerations and tips to improve your installation:
• Keep the ambient temperature constant and below 40°C (104°F). Keep the projector away from heating and/
or air conditioning vents. Changes in temperature may cause drifts in the projector circuitry, which may 
affect performance.
• Keep the projector away from devices that radiate electromagnetic energy, such as motors and transformers, 
slide projectors, speakers, power amplifiers, elevators, etc.
• Use a screen size appropriate for the venue but not larger than required. Installing a large screen in a small 
room is similar to watching television at a close range; too large a screen can overpower a room and interfere 
with the overall effect. As a rule, be no closer than 1.5 times the width of the screen.
2.3 Projector Position
2.3.1 Throw Distance
Throw distance is the distance measured from the front feet of the projector to the screen. This calculation 
determines if there is enough room to install your projector with a desired screen size and if the image will be 
of the right size for your screen.
To estimate the throw distance take the horizontal width of the screen and multiply it by the lens throw ratio. 
The result determines approximately the distance the projector should be positioned from the screen to project 
a focused image large enough to fill the screen. For example, using a 0.73:1 lens, throw distance would 
roughly be 0.73 x screen width.
IMPORTANT! Use the lens and screen size to calculate the precise throw distance using the the lens throw 
calculator provided in the Dealer Section of the Christie Website, or use the tables provided 
in 020-100221-XX. Due to lens manufacturing tolerances for lens focal length, actual throw 
distance can vary ±5% between lenses with the same nominal throw ratio.
2.3.2 Vertical and horizontal position
The correct vertical and horizontal position of the projector in relation to the screen depends on the lens type 
and the screen size. Ideally, the projector should be positioned perpendicular to the screen. This way, the image 
will appear rectangular instead of keystoned (trapezoidal). 
						

							2-10M Series User Manual020-100009-07 Rev. 1 (07-2012)
Section 2: Installation and Setup
The vertical position of the image can be offset (that is moved above or below the optical axis) by adjusting the 
motorized lens mount. The amount of vertical offset available depends on the type of lens installed in the 
projector and can be limited if horizontal offset has been applied. Vertical offset can be expressed as the 
percent of half the image height or the number of pixels of shift from lens center. See Figure 2-1 Vertical 
Offset Examples for illustrated examples of vertical offset.
Table 2.1, Table 2.2 and Table 2.3 specify the vertical offset of each type of lens.
Table 2.1 WUXGA/WXGA Vertical Offset Ranges
Table 2.2 HD 1080p Vertical Offset Ranges
Table 2.3 SXGA+ Vertical Offset Ranges
NOTES: 1) Offsets are subject to ±7% centering tolerance. 2) % Offset = number of pixels of offset/half 
vertical panel resolution x 100.
WUXGA LENS DESCRIPTIONLENS PART 
NUMBERMINIMUM OFFSET
ABOVE OR BELOW 
LENS CENTER
Lens ILS 0.73:1SX+/0.67:1HD 118-100110-XX ±22% ±132 pixels
Lens ILS 1.25-1.6SX+/1.16-1.49HD 118-100111-XX ±82% ±492 pixels
ALL OTHER LENSES ±112% ±672 pixels
WXGA LENS DESCRIPTIONLENS PART 
NUMBERMINIMUM OFFSET
ABOVE OR BELOW 
LENS CENTER
Lens ILS 0.73:1SX+/0.67:1HD 118-100110-XX ±50% ±192 pixels
Lens ILS 1.25-1.6SX+/1.16-1.49HD 118-100111-XX ±120% ±460 pixels
ALL OTHER LENSES ±150% ±576 pixels
HD 1080P LENS DESCRIPTIONLENS PART 
NUMBERMINIMUM OFFSET
ABOVE OR BELOW 
LENS CENTER
Lens ILS 0.73:1SX+/0.67:1HD 118-100110-XX ±35% ±189 pixels
Lens ILS 1.25-1.6SX+/1.16-1.49HD 118-100111-XX ±102% ±551 pixels
ALL OTHER LENSES ±119% ±643 pixels
SXGA+ LENS DESCRIPTIONLENS PART 
NUMBERMINIMUM OFFSET
ABOVE OR BELOW 
LENS CENTER
Lens ILS 0.73:1SX+/0.67:1HD 118-100110-XX ±23% ±121 pixels
Lens ILS 1.25-1.6SX+/1.16-1.49HD 118-100111-XX ±73% ±383 pixels
ALL OTHER LENSES ±100% ±525 pixels