Projector Christie Roadster Hd14k M User Manual

M Series User Manual2-1020-100009-07 Rev. 1 (07-2012)
2 Installation and Setup
This section explains how to install, connect and optimize the projector for delivery of superior image quality. 
Illustrations are graphical representations only and are provided to enhance the understanding of the written 
material. 
2.1 Projector Quick Setup and Installation
The following instructions are for those preferring a quick setup. Refer to the remaining subsections for 
detailed setup instructions.
 
Always power...

2-2M Series User Manual020-100009-07 Rev. 1 (07-2012)
Section 2: Installation and Setup
2. Align the lens interface plate with the lens mount. Align the lens electrical connector with the mating 
connector on the lens mount. Fully insert the assembly straight into the lens mount opening without 
turning. Press using your hand as shown. 
NOTE: When installing the lens, ensure that the lens is not inserted at an angle, as this can cause damage.
3. While holding the lens flat against the lens mount, rotate...

Section 2: Installation and Setup
M Series User Manual2-3020-100009-07 Rev. 1 (07-2012)
2.1.2 Position the Projector
2 people are required to safely lift and install the projector.
Place the projector on a sturdy, level surface and position it so that it is perpendicular to the screen at a suitable 
distance. The further back the projector is positioned for the screen, the larger the image will be.
To level the projector adjust its 3 feet. With the projector positioned perpendicular to the screen the...

2-4M Series User Manual020-100009-07 Rev. 1 (07-2012)
Section 2: Installation and Setup
2.1.4 Connect the Line Cord
IMPORTANT!Use the line cord provided with the projector, or ensure you are using a line cord, power plug 
and socket that meet the appropriate rating standards. Voltage and current requirements are 
listed on the license label, located at the back of the projector.
Connect the projector line cord to the AC receptacle at the AC inlet of the projector, then push the wire clip 
over the plug...

Section 2: Installation and Setup
M Series User Manual2-5020-100009-07 Rev. 1 (07-2012)
2.2.1 About the Projector
Built-In Keypad
The built-in keypad is located on the side of the projector. Use it similarly to the IR remote to control the 
projector. An LCD display is located above the keypad for displaying projector status.
AC Receptacle
The AC receptacle is located above the AC receptacle at the back of the projector. Use this receptacle to plug 
in an appropriately rated line cord. 
Adjustable Feet...

2-6M Series User Manual020-100009-07 Rev. 1 (07-2012)
Section 2: Installation and Setup
Lamp Door
The lamp doors are located at the side of the projector, which provides easy access to the lamp module for 
replacement. The lamp doors are fitted with safety interlocks which switch the lamp off when the door is 
opened. The lamp doors are provided with clear windows to indicate when the lamps are on.
Front and Rear IR Sensors
The two IR sensors receive transmissions from the IR remote from up to 100 feet...

Section 2: Installation and Setup
M Series User Manual2-7020-100009-07 Rev. 1 (07-2012)
2.2.2 Installation Considerations
Proper installation of the projector will ensure the quality of the display. Whether installing a projector 
temporarily or permanently, take the following into account to make sure the projector performs optimally. 
Choose the installation type that best suits your needs: front or rear screen, floor mount or inverted mount.
Front Screen / Floor Mount Installations
Front Screen /...

2-8M Series User Manual020-100009-07 Rev. 1 (07-2012)
Section 2: Installation and Setup
Curved screens have a gain greater than 1.0 with a viewing angle much less than 180 degrees. This type of 
screen does not reflect incident light equally in all directions; instead it is concentrated in a viewing cone. The 
audience sitting within the viewing cone area will see a brighter image than those sitting just outside the area.
2.2.4 Rear Screen Installations
There are two basic types of rear screens:...

Section 2: Installation and Setup
M Series User Manual2-9020-100009-07 Rev. 1 (07-2012)
adequate airflow around the projector, allow free air exchange to the projector with a minimum clearance of 
25cm (10-inch) on the left, right and rear sides of the projector from any walls or other obstructions. Never 
obstruct the air exchange to the projector.
2.2.8 Other Considerations
Other considerations and tips to improve your installation:
• Keep the ambient temperature constant and below 40°C (104°F). Keep...

2-10M Series User Manual020-100009-07 Rev. 1 (07-2012)
Section 2: Installation and Setup
The vertical position of the image can be offset (that is moved above or below the optical axis) by adjusting the 
motorized lens mount. The amount of vertical offset available depends on the type of lens installed in the 
projector and can be limited if horizontal offset has been applied. Vertical offset can be expressed as the 
percent of half the image height or the number of pixels of shift from lens center. See...