Projector Christie Roadie S12 User Manual

INSTALLATION AND SETUP
2-28
Roadie S12/X10 User’s Manual
Protocols are most useful for multiple-projector applications. For example, you might
want to change a keypad protocol if you are working with two projectors and two
remote keypads in the same room and need to control each projector independently
(Figure 2.34). When Keypad A has a different protocol than Keypad B, each keypad
communicates only with the projector having a matching protocol. Or, if you have a
network of two or more projectors...

INSTALLATION & SETUP
Roadie S12/X10 User’s Manual2-29
Step 2
Unlatch and open the empty battery compartment on the back of the keypad as shown
in Figure 2.35.
NOTE: A wired keypad opens as shown, but a cable passes through the battery
compartment cover.
Figure 2.35. Opening the Keypad
Step 3
Find the 4 jumpers located along the latching side of the battery compartment. These
jumpers set the keypad protocol and other settings so that the keypad functions in a
certain manner.
Step 4: Set the Jumpers
Set...

INSTALLATION AND SETUP
2-30
Roadie S12/X10 User’s Manual
Figure 2.36. Locating and Setting the Jumpers
Step 5
Replace battery compartment cover. Plug into projector (wired keypad only) and test.
NOTE: A wired keypad can be converted into an IR remote keypad, and vice versa.
Follow the settings shown above, adding or deleting the cable and batteries as required.
The cable with 3-pin XLR connector is available separately from your dealer.
SHORTCUT METHOD:
You can also issue software protocol settings...

INSTALLATION & SETUP
Roadie S12/X10 User’s Manual2-31
If desired, you can convert an IR remote keypad into a wired remote keypad and vice
versa.
TO CHANGE FROM INFRARED TO WIRED:
• Remove battery compartment cover from back of keypad.
• Remove batteries.
• Wait 1-2 minutes.
• Plug the keypad cable (available separately) into the empty battery
compartment. Make sure that the battery cover is notched smoothly to
accommodate the cable without pinching it.
• Set keypad protocol as desired, using “wired”...

Section 3
Operation
Roadie S12/X10 User’s Manual3-1
This section explains how to use the projector once it has been installed. Please read
through these pages before using the projector for the first time. A good
understanding of projector features and how to access them will help you to take full
advantage of the capabilities of the projector within minutes.
NOTE: Installation involves locating the projector and adjusting it for use at that
location. If you have not yet installed the projector, refer to...

OPERATION
3-2
Roadie S12/X10 User’s Manual
Figure 3.1. Basic Projector Components
REMOTE ZOOM  - Accessed via the Lens key on the keypad, the lens barrel of a
motorized zoom lens (optional) rotates to adjust the size of the image at the current
throw distance. Minimum and maximum image sizes depend on which zoom lens is
installed — see Section 5, Specifications. To adjust zoom manually, remove the zoom
adapter collar (see Section 4, Maintenance) and turn the textured zoom ring by hand.
REMOTE FOCUS -...

OPERATION
Roadie S12/X10 User’s Manual3-3
Section 2, Installation and Setup for an illustrated explanation of offset ranges for all
lenses. Ranges are also listed on page 5-1. Offsets cannot be adjusted manually.
REMOTE CONTROL SHUTTER - Closing the shutter blocks the lens internally and turns
the image to off. Although the lamp remains “on”, its output is reduced to prevent
heat build-up. The shutter is controlled via 
Shutter* on the keypad.
COMPOSITE/S-VIDEO INPUT - Accepts a composite video and...

OPERATION
3-4
Roadie S12/X10 User’s Manual
Figure 3.2. Reading the Status LEDs
NOTE: A steady red power light accompanied by a coded pattern of red and yellow
flashes from the status light indicates an internal system error. Consult the rear LCD
display for an explanation, and see 3.11, Error Conditions. If the problem persists,
contact a qualified service technician available through your dealer.
AC ON/OFF (20 A CIRCUIT BREAKER) – Detects faulty AC and automatically shuts
down the projector to prevent...

OPERATION
Roadie S12/X10 User’s Manual3-5
INFRARED SENSORS - The infrared (IR) sensors on the front and rear of the projector
receive infrared signals from the IR keypad for remote control of projector functions.
For proper operation make sure that these sensors are not blocked.
HARD RESET  - Emergency access for powering down the projector in the event of a
system failure. Insert a pen point or very small screwdriver.
EYEBOLTS – Screw eyebolts into 4 corner holes (top or bottom) to hoist or suspend a...