Projectiondesign Evo2sx+ Projector User Manual

english
11

The keypad is illuminated for operation in dark environments. Several keys have multiple functions.
POWERSwitches the projector between on and standby modes. Press firmly(1 sec) to switch on. Press firmly (1 sec) twice to switch off.
AUTOAdjusting the projector to display a correct image, including position,width, height and overall stability.
MENUActivates the menu system. Use the four arrow keys to navigate and«OK» to activate.
ARROW KEYSUse the arrow keys to navigate the menu system, or...

english
12

INDICATORS
G
INDICATORThe light next to the power key indicates the overall system status by blue, orange and red colors.
PERMANENT BLUE LIGHT The projector is turned on and in normal operation.
PERMANENT ORANGE LIGHTThe  unit  is  in  standby  mode;  no  source(s)  connected,  or  the  source(s)  connected  are inactive  or  switched  off,  thereby  activating  the  powersave  function  (DPMS).  You  may enable or disable the power save function in the SET UP sub menu, DPMS o\
n or off....

english
1

REMOTE CONTROL
H
REMOTE CONTROLThe  remote  control  allows  flexible  access  to  the  projector  settings,  either  through direct  keys,  or  through  the  menu  system.  The  remote  control  is  backlit  for  use  in  dark environments.  It  also  has  a  datajack  that  allows  for  wired  connection  to  the  projector. When the wire is connected, the IR (infra-red) beam and internal batteries are switched off. The remote control may also be used to control presentations by...

english
1

REMOTE CONTROL
DVISelects the DVI input.
VGASelects the VGA input.
AV-MUTEToggles the internal speaker and the projected image on and off. The lamp is not shut off.
STILLToggle function, locking the projected image on and off.
TIMEDisplays date and time. Set the date and time in the MENU system, MISC s\
ub menu.
ASPECTCycles through the aspect ratios available with thecurrent source.
MENUToggles the menu system on and off.
ARROW KEYSUse the arrow keys to navigate in the menu systemand...

english
1

CONNECTOR PANEL
I
CONNECTOR PANEL
A C-VIDEO:
 Used for standard video quality.
B  S-VIDEO:
 Used for improved quality video.
C  YPbPr:
 Used for high quality video reproduction.
D  DVI-D - Digital RGB:
 For a low noise computer and video image.
E  VGA - Analog RGB:
 The standard analog 
  computer graphics interface.
F  RS 22 control:
 Allows for wired remote control and 
  monitoring of many projector functions used in installation environments. 
G  RC: 
Allows connection of...

english
1

SET UP VIDEO
Before setting-up, switch off all equipment.
Three  video  sources  may  be  connected,  using  the  YPbPr  (component),  S-VIDEO (super video) and C-VIDEO (composite video) inputs. 
Component will display more detailed images. Composite video yields images with less detail.
In addition, the DVI-D input can be used with video sources (DVD player fitted with an HDCP™ compliant DVI or HDMI connector) for a pure digital connection.
Connect the power cord.
SETUP COMPUTER
Before...

english
1

Position the projector on a level surface, preferably pointing straight on to the projection screen. Place it at a suitable distance within the throw range of the zoom lens.
A  ZOOM the image for the right size. Reposition the projector if the desired image  
  size is not achievable. 
B  
FOCUS the image properly. 
C  
Level the image by adjusting the rear feet. 
D   To adjust the image vertically on the screen, turn the vertical adjustment knob on  
  top of the unit.
E  
In addition...

english
1

The projector can be ceiling mounted using an approved UL tested/ listed ceiling mount fixture, with a capacity of minimum 12 kg / 26 lbs.
For  ceiling  mount  use  M4  screws  that  penetrate  maximum  5  mm  (0.19  in)  into  the projector body. 
For proper ventilation the minimum distance from ceiling / rear wall should be: 30 / 50 cm (12 / 20 in).
CEILING MOUNT
L 

english
1

After setting-up, switch on all equipment. The projector can be controlled by the keypad, by the remote control or using the RS232 or LAN interfaces. To switch the projector on, firmly  press  the  POWER  button  on  the  keypad  or  the  remote  control.  The  STATUS indicator will turn from yellow to blue when the unit is switched on.
If  the  STATUS  indicator  is  flashing  yellow,  please  wait  until  it  turns  permanent  yellow. Issue the PIN code if activated.
When only one...

english
20

RS 22 AND LAN CONTROL
RS 22
You  may  control  and  monitor  the  projector  remotely  through  the  serial  RS232  control interface.Two RS232 protocols are employed. A simple instruction set (SIS) ASCII protocol gives access to the most frequently used commands. In addition, a binary protocol is available where each command is a series of 32 bytes in one packet. The protocols allow for both SET and GET operations. To utilize GET operations the host needs a routine for receiving...