Projectiondesign Evo2sx+ Projector User Manual

							
userguide • benutzer handbuch • guide d’utilisateur • guía del usario • manuale d’uso • bruksanvisning
•   S X G A +   •   H D7 2 0 
						

							
TABLE OF CONTENTS 
A Table of contents03
B Introduction04
C Safety & Warnings06
D Supplied material09
EOverview10
F Keypad11
G Indicator12
H Remote control13
IConnector panel15
J Set up16
K Image adjustments17
LCeiling mount18
MUsing the projector19
N Menu system22
O Trouble shooting30
PMaintenance31
QService information31
R Lamp change32
STechnical data33
T Declarations36

A 
						

							
english


This  digital  projector  is  designed  with  the  latest  state-of-the-art  technologies  in illumination,  imaging,  optics,  electronics,  thermal  and  industrial  design  in  order  to serve  traditional  as  well  as  novel  imaging  applications  across  a  variety  of  markets, offering features such as:
-  SXGA+ 1400x1050 or HD720 1280x720 pixel DLP™ technology
-    SINGLE CHIP DMD™ with DarkChip™ technology by Texas Instruments®
-    HIGH CONTRAST for vibrant colors and deep blacks
-    HIGH RESOLUTION for unprecedented detail
-    HIGH BRIGHTNESS for larger screens
-    DEEP BLACKS for maximum dynamics
-    COLOR CALIBRATION for precise images
-    REAL TIME CLOCK for timing control
-    REDUCED IMAGE NOISE through high end signal processing
-    FAROUDJA DCDi™ Video processing and de-interlacing
-    ECO MODE for reduced power consumption and lower audible noise
-    VARIABLE LAMP POWER for alignment of multi-screen configurations
-    LONG LIFE LAMP (up to 4000 hours) in low power ECO mode
-    STYLISH AND COMPACT MAGNESIUM DESIGN to fit most     
applications, 
 installed or movable
-    FIVE VIDEO and GRAPHICS INPUTS for virtually any video and data source
-    LAN, RS232 and USB ports for control and monitoring
The specifications and functionality of the product may change without prior notice.
INTRODUCTION
B 
						

							
english


This user guide contains important information about safety precautions and the set-up and use of the projector. Please read the manual carefully before you operate the projector.
SAFETYThis  device  complies  with  relevant  safety  regulations  for  data  processing  equipment for  use  in  an  office  environment.  Before  using  the  projector  for  the  first  time,  please read the safety instructions thoroughly.
WARNINGUse  only  the  cables  and  cords  supplied  with  the  projector  or  original  replacement cables. Using other cables or cords may lead to malfunction and permanent damage of the unit. 
Always  use  3-prong  /  grounded  power  cord  to  ensure  proper  grounding  of  the  unit. Never  use  2-prong  power  cords,  as  this  is  dangerous  and  could  lead  to  electrical shock. 
Never  open  the  unit.  The  projector  contains  no  user  serviceable  parts.  Refer  all repairs to qualified personnel only. Make sure that no objects enter into the vents and openings of the set. 
Do not spill any liquids on the projector or into the vents or openings of the unit. 
Always  remove  lens  cap  before  switching  on  the  projector.  If  the  lens  cap  is  not removed, it may melt due to the high energy light emitted through the lens. Melting the lens cap may permanently damage the surface of the projection lens. 
Do not look into the projection lens when the projector is switched on. The strong light may permanently damage sight.  Do not look into the laser beam when activated on the remote control. Laser light may permanently damage sight. 
Do not point laser beam on people.
Only place the projector on a stable surface, or mount it securely using an approved ceiling-mount.
Do not drop the projector.
Always operate the projector horizontally, within the range of the adjustable rear feet. Operating the unit in other positions may reduce lamp life significantly, and may lead to overheating, resulting in malfunctioning.
Always  allow  ample  airflow  through  the  projector.  Never  block  any  of  the  air  vents. Never cover the unit in any way while running. Allow for sufficient distance to walls and ceilings to avoid overheating. 
Minimum safety distance to any side of the unit is 50 cm / 20” in any direction.
CAUTION! Hot air is exhausted from the rear vent. Do not place objects that are 
sensitive to heat nearer than 0cm / 20” to the exhaust vent.
The projector is designed for indoor use only. Never operate the unit outdoors.
SAFETY & WARNINGS
C 
						

							
english


SAFETY & WARNINGS
Do not operate the projector outside its temperature and humidity specifications, as this may result in overheating and malfunctioning. 
Only connect the projector to signal sources and voltages as described in the technical specification.  Connecting  to  unspecified  signal  sources  or  voltages  may  lead  to malfunction and permanent damage of the unit. 
Allow the unit to cool down for 60 minutes before lamp change.
INFORMATION  AND  WARNING  ABOUT  POTENTIAL  HEALTH  ISSUES  RELATED TO MERCURY VAPOR.
This projector uses a very powerful UHP™ lamp for illumination to produce an extremely bright image. 
This  technology  is  similar  to  other  high-pressure  discharge  lamps  that  are  extensively used  in  cars,  street  lights  and  other  lighting  appliances  today.  These  lamps,  like fluorescent lighting, contain small amounts of mercury. The amount of mercury present in a lamp is far below the limits of danger set by the authorities. It is very important that lamps containing mercury are treated properly to minimize potential health hazards. 
The UHP™ lamp, like any other high brightness projector lamp, is under high-pressure when operating. While the lamp and the projector are carefully designed to minimize the probability of lamp rupture, the lamp may break while operating and small amounts of mercury vapor may be emitted from the projector. The probability of rupture increases when the lamp reaches its nominal life. It is therefore highly recommended that the lamp is replaced when the rated lifetime is reached.
As  a  general  precaution,  secure  good  ventilation  in  the  room  when  operating  the projector.  If  lamp  rupture  occurs,  evacuate  the  room  and  secure  good  ventilation. Children and pregnant women in particular should leave the room. 
When replacing a worn lamp, dispose of the used lamp carefully by proper recycling.
Mercury is a naturally occurring, stable metallic element that may pose a safety risk to people under certain conditions. According to the Public Health Statement for Mercury published  by  the  Agency  for  Toxic  Substances  and  Disease  Registry  (“ATSDR”,  part of  the  United  States  Public  Health  Service),  the  brain,  central  nervous  system  and kidneys  are  sensitive  to  the  effects  of  mercury,  and  permanent  damage  can  occur  at sufficiently  high  levels  of  exposure.  Acute  exposure  to  high  concentrations  of  mercury vapor  can  cause  conditions  such  as  lung  and  airway  irritation,  tightness  in  the  chest, a  burning  sensation  in  the  lungs,  coughing,  nausea,  vomiting  and  diarrhea.  Children and  fetuses  are  particularly  sensitive  to  the  harmful  effects  of  metallic  mercury  to  the nervous system. 
Seek medical attention if any of the above symptoms are experienced or if other unusual conditions are experienced following lamp rupture. 
						

							
english


WEEE INFORMATION
This  product  conforms  to  all  requirements  of  the  EU  Directive  on  waste  electrical and  electronic  equipment  (WEEE).  This  product  shall  be  recycled  properly.  It  can  be disassembled  to  facilitate  proper  recycling  of  it’s  individual  parts.  This  product  is  using projection  lamps  that  shall  be  recycled  properly.  Consult  your  dealer  or  relevant  public authority regarding drop-off points for collection of WEEE.
WARNINGThis  product  contains  chemicals,  including  lead,  known  to  the  State  of  California  to cause birth defects or other reproductive harm. Recycle properly, do not dispose of in ordinary waste!
REMOTE CONTROL WARNINGLaser radiation class II product; wavelength 670nm; maximum output 1mW.
Remote control complies with applicable requirements of 21 CFR 1040.10 and 1040.11.
Remote control complies with applicable requirements of EN 60 825-1: 1994 + A11
SAFETY & WARNINGS 
						

							
english


WARNING SYMBOLS
READ USER GUIDEAttention! Read the user guide for further information!
DANGEROUS VOLTAGEDanger! High voltage inside the product!
HOTWarning! Hot surfaces!
WAITWarning! Wait until cooled down!
MERCURYWarning! Lamp contains mercury! Recycle properly, do not dispose of in ordinary waste!
UVWarning! UV radiation inside the product!
RECYCLEWarning! Recycle properly, do not dispose of in ordinary waste!
NO TELEPHONEWarning! Do not connect to telephone lines!
SAFETY & WARNINGS 
						

							
english


SUPPLIED MATERIAL
Power Cord(country dependent)
D
Projector
Remote control with batteries
User guide
Bag
Before Set up and UseUnpack the supplied parts and familiarise yourself with the various comp\
onents. 
						

							
english
10

A  Lens
B  IR sensor
C  Ventilation
D  Power connector 
E  Keypad 
F  Connector panel
G 
Lens shift
H   Adjustable feet
I  Security lock
J  Ceiling mount
OVERVIEW
E
ABC
DBFC
E
H
J
I
B
C
C
C
G
11
G