Polaroid Projector Polaview 215E User Manual

60Polaview 215E LCD Projector UserÕs Guide
Getting started
To Use the Auto Setup feature
The signal mode is identiÞed and the vertical position, horizontal position, 
horizontal size, and phase are automatically adjusted. Click on Auto Setup at the 
bottom of the setting window.
¥ You may also select Option  Auto Setup.
¥ The on-screen display at right will appear during 
auto adjustment.
¥ Auto Setup may not be possible with some 
computer types.
ProMouse Software details
File Menu
¥ Save
Saves the...

English61
Getting started
How to program
1.Click on the remote key you 
want to be programmed in the 
setting window.
The screen shown at right will 
appear.
2.Operate the desired shortcut 
command on the PC.
The key selected in step 1 will be programmed with the shortcut command 
operated in step 2.
Programmed shortcut keys are indicated in the setting window.
Because the Clear Screen command is necessary to delete lines or stamp 
marks from the screen, the X key is programmed as Clear Screen at the...

62Polaview 215E LCD Projector UserÕs Guide
Appendix
Appendix
Maintenance
Warning IndicationsStatus Code Display Indications
This LCD projector has a STATUS CODE display that calls your attention to 
problem conditions existing inside the LCD projector. The LCD projector displays 
a status code indication each time an internal problem is detected. If any of the 
following indications appear in the STATUS CODE display, immediately turn off 
the MAIN power. Then, see the chart below.
STANDARD
VOLUMEMODE...

English63
Appendix
Note: Please wait one minute before turning the power back on, to allow the lamp 
to cool. A much longer time may be required if the LCD projector has reached an 
abnormally high internal temperature.
Cleaning the Air FilterThe air Þlter should be cleaned about every 100 hours. Also, clean the air Þlter if 
ÒA-0Ó appears in the STATUS CODE display.
Replace the Þlter when it is clogged or dirty even after cleaning.
Cleaning procedure
Tools required: Vacuum cleaner.
Wait until the...

64Polaview 215E LCD Projector UserÕs Guide
Appendix
3.Remove the air filter unit
Hold the indent on the air Þlter unit with your hands and pull the air Þlter unit 
out of the LCD projector.
4.Clean the filter.
Gently remove any accumulated dust from the air Þlter unit with your vacuum 
cleaner.
Caution: Operating the LCD projector with a torn or damaged air Þlter 
may cause damage to the LCD projector.
5.
Replace the air filter unit.
Slide the air Þlter unit into the LCD projector until the hollows in...

English65
Appendix
Lamp ReplacementWarning: If Status Code ÒL-nÓ (see page 62) is displayed on the Status 
Code Display when lamp is not turned on, take the LCD Projector to your 
nearest Service Center for repair as there is danger of injury due to lamp 
fragments.
Lamp replacement period
The LCD projector lamp has a limited operating life of approximately 1100 hours.
ÒLAMP TIME REMAINING 10hÓ will be displayed on screen when the operation 
time reaches 1090 hours. Then, each time the power is turned...

66Polaview 215E LCD Projector UserÕs Guide
Appendix
Lamp replacement procedure
Caution: Because of possibility of injury, strictly follow the lamp replacement 
procedure outlined below.
Order Lamp: 630146 Tools required: A coin.
1.After the cooling fan has stopped and the STANDBY(R) ON(G) indicator 
turns solid red, set the MAIN power switch to OFF and unplug the power 
cord.
Note: Please wait more than one hour before replacing the lamp.
If you need to replace the lamp more urgently
1.
The LCD Projector...

English67
Appendix
4.Remove the lamp unit screw.
Remove the lamp unit screws (2), then grasp the lamp unit handle and carefully 
pull it from the LCD projector. Keep the lamp housing opening to your right. 
Do not touch the lamp or point the lamp opening at anyone.
Warning: The lamp may be hot. Be careful when handling.
Caution: High-pressure lamps may explode if improperly handled. 
Danger of injury due to lamp fragments.
5.Install the new lamp unit.
Remove the 630146 lamp from the LCD projector and...

68Polaview 215E LCD Projector UserÕs Guide
Appendix
10 .Press Z orX to select SET UP PROJECTOR, and then press C or V to 
display the screen.
11.Press Z orX to select LAMP TIME RESET, and then press C or V to 
display the screen.
12.Press C or V to select YES. ÒPush POWER button to resetÓ will appear.
13.Press POWER to reset the lamp time to Ò0Ó.
When you change to a new 
lamp reset lamp time. 
Have you finished yet?
NOYES
SELECT : PUSH C or V
END : PUSH MENU
Lamp Time  Reset 

English69
Appendix
Before Requesting Service
If the LCD projector unit fails, check the following before calling your dealer for 
service.
Where to get help
If at any time you need help:
¥ Check ÒBefore Requesting ServiceÓ above.
¥ Call your dealerÕs technical support line and explain your problem.
¥ Call Polaroid Corporation. Refer to listing of Polaroid ofÞces and service 
centers.
Problem Possible Cause
The power does not turn on.¥ The power cord may not be connected.
¥ The MAIN power switch on the...