Pocket Radio Sangean Dt220v Operating Instruction

							DT-220V
Operating instruction
Instruccions de manejoGB
E 
						

							1 
						

							2 
						

							3GB   Controls
    Telescopic Aerial                    Display
    Preset 6-10                            Display button
    Stereo/Mono/Alarm button
    Band/Time set button
    Power button                          Light button
    Tuning up/down button           Preset 1-5
    Lock switch                            Volume Control
    Loudspeaker/Headphone switch
    Headphone socket                DC input socket
    Auto wind earphones
    Auto wind earphones switch
    Battery compartment
    RESET
  Display
    Waveband and A.M./P.M. indicator
    90 minutes auto shut off indicator
    Alarm indicator
    Stereo indicator
    Key lock indicator
    Preset 6-10
    Preset indicator
    Low battery indicator
    Frequency unit
    Frequency/Time display12345678910111213141516171819ABCDEFGHIJ 
						

							4  Installing batteries
1. position the radio face down.
2. Press the catch and slide in the direction of the
    arrow.
3. Lift up the battery cover.
4. Insert 2xUM-3 (AA) size batteries. Make sure the
    batteries are positioned in accordance with the
    diagram indicated.
5. Replace the battery cover.
  Battery replacement
The battery indicator       will appear and flash in the
display when the batteries are in need of replacement
. After removing the batteries, you have
approximately 3 minutes to replace the batteries after
which clock and memory information will be lost.
  Setting the clock time
The clock will start running when the batteries are
installed. When the batteries are installed for the first
time, the display will show 0:00.
Note:Time can only be set with the radio switched off.
1. Ensure that the radio is switched off .
2. Press and hold down the Time Set button for more
    than 2 seconds until the hours digit begins to flash
    in the display .
3. Whilst the hours digit is flashing, adjust the hours
    using Tuning Up/Down buttons.
4. Press the Time Set button, the minute digit begins
    to flash in the display.
5. Whilst the minute digit is flashing, adjust the
    minutes using the Tuning Up/Down buttons.
6. Press the Time Set button to complete time setting. 
						

							5GB   Setting the alarm time
1. Ensure that the radio is switched off.
2. Press and hold down the Alarm button for more
    than 2 seconds until the hours digit and alarm
    symbol begin to flash in the display .
3. Whilst the hours digit is flashing, adjust the hours
    using the Tuning Up/Down buttons.
4. Press the Alarm button, the minute digit begins to
    flash in the display.
5. Whilst the minute digit is flashing, adjust the
    minutes using the Tuning Up/Down button.
6. Press the Alarm button to complete alarm time
    setting. The Alarm symbol will appear on the
    display indicating the alarm is set.
  Wake to alarm
1. At the pre-selected time, the alarm will beep.
    The alarm may be turned off for 24 hours by
    pressing any button. The alarm will switch off
    automatically after 3 minutes .
2. To permanently cancel the alarm, press the alarm
    button, the alarm symbol       will be removed from
    the display. 
						

							6  Operating the radio-search tuning
1. Switch on your radio by pressing the Power Button.
Note: The radio is originally set to be 90 minutes auto
         shut off after Power is switched on (       symbol
          will appear on the display). If you don’t need
         this feature, press Power button for more than
         2 seconds until        symbol removed from the
         display .
2. Select the required waveband by repeatedly
    pressing the Band button. On FM and TV bands,
    fully extend the Telescopic aerial. On AM (MW)
    band, rotate your radio for best reception.
3. Press and hold down either the Tuning Up or Down
    buttons until frequency in the display begins to
    change rapidly. Release the button.
4. Your radio will scan the selected waveband,
    stopping each time if finds a station of sufficient
    strength. Adjust the volume control to the required
    level. 
						

							7 DGB  Operating the radio – manual tuning
1. Switch on your radio by pressing the Power button.
2. Select the desired waveband using the Band
    button. The waveband selected will appear in the
    display. On FM/TV bands, fully extend the
    Telescopic aerial. On AM (MW) band, rotate
    your radio for best reception.
3. A single press on either the Tuning Up/Down will
   change the frequency up or down. Adjust the
   Volume control to the required level.
  AM(MW) tuning step
In Europe and other parts of the world AM (MW)
tuning steps are 9 kHz, in America the AM tuning
step is 10 kHz.
To change the AM tuning step from 10 kHz to 9 kHz,
proceed as follows,
1. Switch on your radio and select the AM (MW)
    waveband.
2. Switch off the radio.
3. Press Tuning Down then Power button, the radio
   will be changed into 9 kHz tuning step on AM band.
To change the AM tuning step from 9 kHz to 10 kHz,
proceed as follows,
1. Switch on your radio and select the AM (MW)
    waveband.
2. Switch off the radio.
3. Press Tuning UP then Power button, the radio will
    be changed into 10 kHz tuning step on AM band. 
						

							8  Presetting stations
You may store up to 10 stations each on FM, AM
(MW) and TV bands giving a total of 30 preset
stations.
1. Tune into the required stations using one of the
    tuning methods previously described .
2. To store the station, press and hold down one of
    the PRESET button 1-5 for more than 2 seconds
    until display shows preset location.
3. To store the station into preset 6-10, press +5
    button, display will show +5, then press and hold
    down one of the PRESET button 1-5 for more than
    2 seconds until display shows preset location.
  Recalling a preset station
1. Switch on your radio using the Power button.
2. Select the desired waveband using the Band
    button.
3. Simply press one of Preset buttons 1-5 to recall
    the required preset stations. To recall preset
    stations 6-10, press +5 button, then the Preset
    button 1-5.
  Display modes
Whilst radio is switched on, press Display button to
change between frequency and normal time. 
						

							9GB   Display backlight
Pressing the Light button will switch on the display
backlight and illuminate the display for approximately
7 seconds.
  Lock switch
The lock switch located on the right side of your radio
is used to prevent unintentional operation.
1. Slide the Lock switch to the up ‘ locked ‘ position,
    the       symbol will appear in the display. The
    Power and all other buttons will be disabled except
    the Light button . This will prevent accidental
    operation when the radio is packed in a suitcase.
    To release the Lock switch, move the switch to the
    down ‘unlocked’ position, the       symbol will be
    removed from the display.
  Earphones
The earphones fitted to your radio are equipped with
an auto wind system to allow for easy storage.
1. Gently pull out the earphones from the right hand
    side of the radio.
2. Slide the Loudspeaker/Headphone switch to the
           position, the loudspeaker will mute.
3. to retract the earphones, slide the switch on the
    rear of the cabinet. Hold onto the earphones while
    they rewind into the cabinet.
4. Slide the Loudspeaker/Headphone switch to the
            position to return to normal operation.