Plus Projector U7 137 User Manual

E-21
Connecting Personal Computers and Video Equipment
Connections with the RGB OUT Connector
• The image from the computer connected to the DVI or RGB IN connector is output.
• The image of the connector selected with the input selection function is output.
• If an input other than DVI or RGB is selected with the input selection function, the output does not switch.
• While controlling the personal computer in front of you, the same screen can be projected with the projector. This allows
personal...

E-22
Power Cable Connections and Switching the Power On/Off
D
V
I
STANDBY STATUSSTANDBY STATUSSTANDBY STATUS
There is an order in which the power cable is connected and the power is switched on/off.
Operating
1Connect the AC IN connector of the projector and the power outlet using the supplied power cable.The STANDBY indicator will light in amber, and the unit will enter the standby mode.
Firmly plug in all the way.
To wall outlet
2Switch on the projector powerPress the STANDBY button.
This indicator is...

E-23
Power Cable Connections and Switching the Power On/Off
When [Menu Language Select] is Displayed Upon Switching On the Power
The first time the power is switched on after purchase, [Menu Lan-
guage Select] will be displayed. Follow the procedure described be-
low and select the display language of the projector.
If the image is blurred, turn the focus ring counterclockwise or clock-
wise to focus it. See Page E-26.
1Press the SELECT (
) buttons and align the deep
blue cursor with [English]....

E-24
Power Cable Connections and Switching the Power On/Off
Finishing
1Switch off the power of the connected equipment
2Switch off the power of the projector
Press the STANDBY button.
Warrning
Do not unplug the power cable while the STANDBY indicator is blinking amber. Doing so may shorten the life of the lamp
or damage the projector.
Power OffOK ?
The STANDBY indicator changes to blinking amber and lights a steady
amber after about 90 seconds (when the unit enters the standby mode).
STANDBY STATUS...

E-25
Adjustment of the Projection Screen
Switch on the power of the connected equipment and make the adjustments with the video signal being input to the
projector.
Adjustment of the Projection Screen
2Adjust the projection image to the screen.Check that the screen is set level and vertically.
(1) If the image is shifted to the left or right, move the main unit horizontally. (Align the center of the screen and the center of
the projector lens.)
(2) If the image is shifted vertically, move the image up or...

E-26
Adjustment of the Projection Screen
(
1)
(
1)
RGB IN
RGB OUT
(
2)
3Turn the focus ring and adjust the focus of the screen
Focus ring
Making Adjustments with the Adjusters
Raising the projection image
While viewing the projection image, (1) press and hold
the front adjuster buttons located at the left and right and,
(2) raise the projector to align the image with the screen,
then release your fingers.
Turn the left and right front adjusters for fine adjustment.
Adjust so that there is no shaking of...

E-27
General Operation
This section describes the use of direct operation with the main unit or remote control buttons.
For information about operation using the menu, see Menu Operation Method on Page E-27 and the various items on
Pages E-44 to E-57.
Input Selection
MENU SOURCEAUTO
QUICK
MENU
FREEZEMUTELASER
AUTO
TIMER
VOL
ZOOM
R-CLICK/
CANCEL
QUICK MENU
ENTER
STANDBY
Q
12
34
RGBVIDEO
Note
* When you do not operate source selection, the projector will assume the input selec-
tion condition that was...

E-28
Freezing a Moving Picture
This function is used to stop and view a moving picture. Note that the input
image continues to advance even though the picture there is a still picture
condition.
A press of the FREEZE button changes the screen to a still picture. A
further press returns the screen to a moving picture.
General Operation
MUTELASER
AUTO
TIMER
VOL
ZOOM RGBVIDEO
R-CLICK/
CANCEL
QUICK MENU
ENTER
STANDBY
Q
12
34
FREEZE
Cancelling Video and Audio Temporarily
This function is used to cancel the...

E-29
General Operation
Enlargement of the Image and Video Movement
This function digitally enlarges the personal computer image and video
image.
(1) Press the ZOOM button to enlarge the image.
The zoom display appears when the ZOOM button is pressed.
When the 
 button is pressed, the image is enlarged approximately 2
times, and when the  button is pressed the image is reduced (re-
turning to 1:1).
• Images input from a Digital, Image Viewer or Network cannot be
enlarged.
(No enlargement) (Approximately...

E-30
General Operation
Using the Presentation Timer
Note:
* The timer display is not displayed when a menu or message is displayed or when the “Wireless Projector” setting screen is being projected,
but the timer continues functioning. The timer display is also not displayed when no signals are being input.
* While the presentation timer is being displayed, screen movement will not be possible in the zoom mode.
* Timer key operations cannot be performed when the input is set to “Image Viewer”.
[Timer...